Wyrestorm MX-0404-H2, MX-0606-H2 Quick Start Manual
4x4 or 6x6 4K HDMI Matrix Switcher
with HDCP 2.2 Encryption
MX-0404-H2 | MX-0606-H2
Quickstart Guide
In the Box
1x MX-0404-H2 or MX-0606-H2 Matrix Switcher
1x Handheld IR Remote
1x IR Receiver (38kHz)
1x AC Power Cord with EU Plug
1x AC Power Cord with US Plug
1x AC Power Cord with UK Plug
1x USB to DB9 RS-232 Cable
2x Mounting Brackets
1x Quickstart Guide
Basic Wiring Diagram
KEY
HDMI
HDBaseT / Ethernet
IR / RS-232
Power
HDMI from
source
HDMI to
display
HDMI to
display
HDMI from
source
RS-232 to Control System
LAN
Cat5/5e/6
AC Mains
UHD Display
UHD Display
UHD Source
UHD Source
IR Receiver
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI connections while
the matrix is powered on. Doing so may cause damage to the units or
connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Before Beginning
• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
• Verify that all items are included in the packaging per the In the Box
list.
Pre Wire
1. (Optional) If using IR receivers or an IR control system, run the wire
and terminate per the IR Ext (Receiver) Wiring section.
2. (Optional) If using RS-232 to control the matrix, run the wire and
terminate per the RS-232 Wiring section.
Installation
1. Connect an HDMI source to the HDMI In on the Matrix using an
HDMI cable from a high quality brand such as WyreStorm Express.
Repeat for additional HDMI sources.
2. Connect a display device to Output 1 using an HDMI cable from
a high quality brand such as WyreStorm Express. Repeat for
additional displays.
3. (Optional) Using the included IR receiver, connect the 3.5mm (1/8in)
stereo plug to the matrix IR Ext port. If using a control system,
connect an IR out port on the control system to the IR Ext port on
the matrix using the WyreStorm CAB-IR-LINK or the cable created
in Pre Wire step 1.
4. (Optional) Using the cable created in Pre Wire step 2, connect the
9-pin DB9 Female connector to the RS-232 port on the matrix and
the opposite end to a port on a control system.
5. Connect the supplied AC power cord and power on the matrix.
6. Congure EDIDs per the EDID Settings section.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-H2 | MX-0606-H2 Quickstart Guide | 160722
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Pure HDMI 4x4 or 6x6 matrix switch with support for full 4K resolutions and HDCP 2.2.
Front Panel
Rear Panel
Source/Output
Selection
Displays the source input number currently selected for the corresponding output number.
MX-0404-H2: 1-4
MX-0606-H2: 1-6
IR Sensor Receives IR signals from included handheld IR remote or attached emitter from IR control system for matrix control.
Source/Output
Navigation
Left/Right: Output Selection
Up/Down: Input Selection
Enter: Conrm Selection
Power Switch
Up: Power On matrix
Down: Power Off matrix
Power In
IEC 3-prong
Connect to 100~240V AC 50/60Hz using the included IEC power cord.
HDMI In
19-pin type A HDMI female:
MX-0404-H2: 1-4
MX-0606-H2: 1-6
Supports HDMI and DVI/D (requires adapter-not included). Limited to 600MHz pixel clock.
LAN
8-pin RJ-45 female | 10/100 Mbps auto-negotiating
Connect to a network router or switch for accessing the Web UI or control via an IP based control system.
RS-232
9-pin DB9 Female
Connect to an RS-232 control system to control the matrix or a PC for testing and rmware updates. See RS-232
Wiring.
HDMI Out
19-pin type A HDMI female:
MX-0404-H2: 1-4
MX-0606-H2: 1-6
Supports HDMI and DVI/D (requires adapter-not included).
IR Ext
3.5mm (1/8in) Stereo Jack
Connect to an Included IR receiver or control system to control the operation of the matrix.
See IR Ext (Receiver) Wiring.
EDID
3 Position Dipswitch:
Used to set EDIDs to correct resolution conflicts between the source and the display.
See EDID Settings.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-H2 | MX-0606-H2 Quickstart Guide | 160722
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
2 of 4
Loading...