Wyrestorm EX-70-H2X v1 Quick Start Manual
4K UHD HDCP 2.2 HDBaseT 5-Play Extender Set with 2-way PoH,
Ethernet, IR and RS-232 (4K: 70m/230ft | 1080p: 100m/328ft)
EX-70-H2X v1
Quickstart Guide
In the Box
1x EX-70-H2X Transmitter
1x EX-70-H2X Receiver
1x 12V DC 2A Power Supply (US/UK/EU)
2x 2-pin Screw Down Phoenix Connectors
2x 3-pin Screw Down Phoenix Connectors
2x Wide-band IR Emitters
2x Wide-band IR Receivers (30-50KHz)
4x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI
or
HDBaseT
Cat5e/6/6a
HDMI
IR Emitter
IR Emitter
IR Receiver
HDMI Source
UHD/4K Display
12 DC 2A
Power Supply
EX-70-H2X Transmitter (TX)
EX-70-H2X Receiver (RX)
IR to Control System
CAB-IR-LINK (Sold Separately)
KEY
HDMI
HDBaseT Cat5e/6
IR TX and RX
Power
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while devices
are powered on may cause damage. WyreStorm recommends powering off
devices before disconnecting these connections.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Refer to the Installation Guide and other documentation on the
product page for additional information.
Installation
Before Beginning
• WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about the product.
• Verify that all items are included in the packaging per the In the Box list.
Pre Wire
1. Run a Cat5e/6/6a cable from the transmitter location to the receiver
location. Terminate the cable per the HDMI/HDBaseT Wiring section.
2. (Optional) If using 3rd party IR emitters or connecting blocks at either
the transmitter or receiver, run the wire and terminate per the IR TX
(Emitter) Wiring section.
3. (Optional) If using RS-232 pass-through, run the wire and terminate per
the RS-232 Wiring section.
4. (Optional) If using 3rd party IR receivers at either the transmitter or
receiver, run the wire and terminate per the IR RX (Receiver) Wiring
section.
Transmitter Installation
1. Connect an HDMI source to the HDMI In on the transmitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT Out.
4. (Optional) Connect the 3-pin connector to the RS-232 port on the
transmitter and the opposite end to a port on a control system.
5. If using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the DC 12V jack.
Receiver Installation
1. Connect the HDMI Out on the receiver to an input on the display using
an HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT In.
4. (Optional) If using RS-232 pass-through, connect the 3-pin connector
to the RS-232 port on the receiver and the opposite end to a port on the
device being controlled.
5. If not using PoH to power either the transmitter or receiver, connect the
included 18V DC 1A power supply to the 18V DC 1A jack on the either
device.
Copyright © 2016 WyreStorm Technologies | wyrestorm.com
EX-70-H2X V1 Quickstart Guide | 161102
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Note: The following information applies to version 1 of this product as identied by v1 after the model number on the product label.
Front Panel (TX/RX) Rear Panel (TX/RX)
SET (TX)
3 Position Dipswitch
Used to enable/disable long cable mode
and congure RS-232 port operation. See
Transmitter Set Switch for operation.
RS-232 Mode (RX)
Used to congure RS-232 port operation. See
Receiver RS-232 Mode for operation.
EDID
3 Position Dipswitch
Used to set EDIDs to correct resolution
conflicts between the source and the display.
See EDID Settings for operation.
Power LED
Solid: The transmitter is powered On
Off: The transmitter is powered Off
Status LED
Flashing: The transmitter is operating
normally.
Off: The transmitter is Not operating
normally.
HDCP LED
Solid: Audio and Video signal is HDCP
protected.
Flashing: Audio and Video signal is not HDCP
protected.
Off: No Audio and Video signal.
LINK LED
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
Power In
5.5mm Screw Down Barrel Jack
2-pin Phoenix Connecter
Connect to the included 18V DC 1A power
supply to the transmitter. A power supply
is not required on the receiver as it will be
powered using PoH. See Power Supply Wiring
for important information.
HDBT Out (TX)
HDBT In (RX)
8-pin RJ-45 female | 10/100 Mbps autonegotiating
Connect the transmitter HDBT Out to receiver
HDBT In using the cable created in Pre Wire
step 1.
HDMI In (TX)
HDMI Out (RX)
19-pin type A HDMI female digital video/
audio: Supports HDMI and DVI/D (requires
adapter-not included). Limited to 297MHz
pixel clock
IR TX/RX
3.5mm (1/8in) Mono Plug
IR TX: Connect to the supplied IR emitter to
control a local device from the remote display
location via HDBaseT.
IR RX: Connect to the supplied IR receiver to
send IR to the remote display via HDBaseT.
See IR Wiring.
RS-232
3-pin Screw Down Phoenix Connector
Used to send and receive RS-232 signals to/
from the source location via HDBaseT and
rmware updates. See RS-232 Wiring.
Ethernet
8-pin RJ-45 female | 10/100 Mbps autonegotiating
Connect to a Local Area Network or network
device for Ethernet pass-through via
HDBaseT.
Copyright © 2016 WyreStorm Technologies | wyrestorm.com
EX-70-H2X V1 Quickstart Guide | 161102
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
2 of 4
EX-70-H2X Transmitter (TX)
EX-70-H2X Receiver (RX)
A B C D E F
EX-70-H2X Transmitter (TX)
EX-70-H2X Receiver (RX)
A B C D E F
Loading...