Wyrestorm EX-70-H2 Quick Start Manual & User Manual
HDBaseT 4K UHD Extender Set with 1-way PoH
and Bidirectional IR & RS-232 (70m/230ft)
EX-70-H2
Quickstart Guide
In the Box
1x EX-70-H2 Transmitter
1x EX-70-H2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
2x 3-pin Screw Down Phoenix Connectors
2x Wide-band IR Emitters
2x Wide-band IR Receivers (30-50KHz)
4x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI Display
HDMI
HDMI
IR Emitter
IR Emitter
IR Receiver
18V DC 1A
Power Supply
IR to Control System
CAB-IR-LINK (Sold Separately)
EX-70-H2 Transmitter (TX)
EX-70-H2 Receiver (RX)
4K/UHD HDMI Source
KEY
HDMI
HDBaseT Cat5e/6/6a
IR TX and RX
Power
HDBaseT
Cat5e/6/6a
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while devices
are powered on may cause damage. WyreStorm recommends powering off
devices before disconnecting these connections.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Detailed installation and conguration information may be found in
the download tab located on the product page.
Installation
Before Beginning
• WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about the product.
• Verify that all items are included in the packaging per the In the Box list.
Pre Wire
1. Run a Cat5e/6/6a cable from the matrix location to the receiver location.
Terminate the cable per the HDMI/HDBaseT Wiring section.
2. If using 3rd party IR emitters or connecting blocks at either the
transmitter or receiver, run the wire and terminate per the IR TX (Emitter)
Wiring section.
3. (Optional) If using RS-232 pass-through, run the wire and terminate per
the RS-232 Wiring section.
4. (Optional) If using 3rd party IR receivers at either the transmitter or
receiver, run the wire and terminate per the IR RX (Receiver) Wiring
section.
Transmitter Installation
1. Connect an HDMI source to the HDMI In on the transmitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT Out.
4. (Optional) Connect the 3-pin connector to the RS-232 port on the
transmitter and the opposite end to a port on a control system.
5. If using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the 18V DC 1A jack.
Receiver Installation
1. Connect the HDMI Out on the receiver to an input on the display using
an HDMI cable from a high quality brand such as WyreStorm Express.
2. (Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the IR TX port.
3. Connect the cable created in Pre Wire step 1 to the HDBT In.
4. (Optional) If using RS-232 pass-through, connect the 3-pin connector
to the RS-232 port on the receiver and the opposite end to a port on the
device being controlled.
5. If not using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the 18V DC 1A jack.
Copyright © 2016 WyreStorm Technologies | wyrestorm.com
EX-70-H2 Quickstart Guide | 160803
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Front Panel (TX/RX) Rear Panel (TX/RX)
Power LED
Solid: The receiver is powered On
Off: The receiver is powered Off
Status LED
Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
HDCP LED
Solid: HDCP content is present.
Flashing: HDCP content is not present.
Off: No signal.
LINK LED
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
RS-232 Mode
Switches the mode for the RS-232 port.
Normal: RS-232 HDBaseT pass-through.
Update: RS-232 rmware update.
Power Input
5.5mm Screw Down Barrel Jack
2-pin Phoenix Connecter
Connect to the included 18V DC 1A power
supply to the transmitter. A power supply
is not required on the receiver as it will be
powered using PoH. See Power Supply Wiring
for important information.
Status LED
8-pin RJ-45 female | 10/100 Mbps autonegotiating
Connect the transmitter HDBT Out to receiver
HDBT In using the cable created in Pre Wire
step 1.
HDCP LED
IR TX - 3.5mm (1/8in) Mono Jack: Connect
to the supplied IR emitter to control a local
device from the remote display location via
HDBaseT.
IR RX - 3.5mm (1/8in) Stereo Jack: Connect
to the supplied IR receiver to send IR to the
remote display location via HDBaseT.
See IR Wiring for more information.
LINK LED
19-pin type A HDMI female
Supports HDMI and DVI/D with adapter
RS-232 Mode
3-pin Phoenix Connector
Used to transmit RS-232 over HDBaseT to
the remote location and for rmware updates.
See RS-232 Wiring for more information.
Copyright © 2016 WyreStorm Technologies | wyrestorm.com
EX-70-H2 Quickstart Guide | 160803
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
2 of 4
EX-70-H2 Transmitter
EX-70-H2 Receiver
A B C D E
EX-70-H2 Transmitter
EX-70-H2 Receiver
A B C D E
Loading...