Wyrestorm EX-70-G2 User Manual
4K UHD HDBaseT Extender Set
with HDCP 2.2 & 2-way PoH
EX-70-G2
Quickstart Guide
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Identifying Product Versions
This product was released in 2 different versions which contain different
chassis designs and feature sets. The differences are identied throughout
this document in order to make installation and use easier. Versions can
be identied by a v# after the model number on the product chassis model
number sticker. Note that version 1 of this product may not contain a v1 after
the product while all version 2s will contain a v2 after the model number.
In the Box
1x EX-70-G2 Transmitter
1x EX-70-G2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
1x IR Emitters
1x IR Receivers
2x 3‐pin Screw Down Male Phoenix Connectors
4x Mounting Brackets (2x for TX | 2x for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI Source
HDMI Display
IR to Control System
CAB-IR-LINK (Sold Separately)
18V DC 1A
Power Supply
IR Emitter
HDMI
EX-70-G2 Transmitter (TX) EX-70-G2 Receiver (RX)
HDBaseT
Cat6/6a/7
IR Receiver
IR Emitter
HDMI
KEY
HDMI
HDBaseT Cat5e/6/6a
IR TX and RX
Power
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
1 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
Front Panel (TX/RX) Rear Panel (TX/RX)
EX-70-G2 Transmitter
EX-70-G2 Receiver
Power LED
Status LED
HDCP LED
LINK LED
A B C D
Solid: The receiver is powered On
Off: The receiver is powered Off
Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
Solid: HDCP content is present.
Flashing: HDCP content is not present.
Off: No signal.
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
EX-70-G2 Transmitter
A B C ED
EX-70-G2 Receiver
5.5mm Screw Down Barrel Jack
Connect to the included 18V DC 1A power
supply to the transmitter or receiver. A power
Power Input
HDBT In
HDBT Out
IR TX/RX
supply is not required on the other end as it
will be powered using PoH.
See Power Supply Wiring for important
information.
8-pin RJ-45 female
Connect the transmitters HDBT Out to
receivers HDBT In.
IR TX - 3.5mm (1/8in) Mono Jack: Connect
to the supplied IR emitter to control a local
device from the remote display location via
HDBaseT.
IR RX - 3.5mm (1/8in) Stereo Jack: Connect
to the supplied IR receiver to send IR to the
remote display location via HDBaseT.
See IR TX/RX Guidelines for more
information.
RS-232 1x RS-232: 3-pin Phoenix (v2 chassis only)
HDMI In (TX)
HDMI Out (RX)
19-pin type A HDMI female
Supports HDMI and DVI/D (requires adapter not included).
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
2 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
Loading...