NexSentry™, QuadraKey™, NexKey™, KeyMate™, 2Smart™, and DigiReader™ are trademarks of
WSE.
ProProx™, ISOProx™, DuoProx™, and Corporate 1000™ are trademarks of HID Corporation.
Teflon™ is a trademark of the DuPont Corporation.
Printed in the U. S. A.
iiP/N 6600025, Rev . D
DigiReader Series WSE
Проектирование. Монтаж. Продажа. - http://vskd.ru
LIMITED WARRANTY
WSE warrants to the original user the equipment manufactured by WSE as described herein to be free
from defects in material and workmanship for a period of one year from the date of purchase by such user
or fifteen (15) months from the date of shipment from the factory, whichever is sooner (command key/
magnetic stripe card warranties differ, see below*), provided:
IWSE has been notified within such period by return of any alleged defective equipment, free and
clear of any liens and encumbrances to WSE or its authorized dealer at the address specified,
transportation prepaid;
I Ithe equipment has not been abused, misused or improperly maintained and/or repaired during
such period;
I I Isuch defect has not been caused by ordinary wear and tear;
IVsuch defect is not a result of voltage surges/brownouts, lightning, water damage/flooding, fire,
explosion, earthquakes, tornadoes, acts of aggression/war, or similar phenomena;
Vaccessories used as integral to WSE systems have been approved by WSE (e.g., coaxial
cables, batteries, etc.);
VIthe equipment has been installed, the installation supervised or installation tested by an
authorized WSE dealer.
WSE shall, at its option, either repair or replace, free of charge, the equipment found, upon WSE’s
inspection to be so defective, or if agreed upon, to refund the purchase price, less a reasonable allowance
for depreciation, in exchange for the equipment.
WSE MAKES NO OTHER WARRANTY, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE
DURATION OF THE EXPRESSED WARRANTY AS SET FORTH ABOVE.
WSE’S MAXIMUM LIABILITY HEREUNDER IS LIMITED TO THE PURCHASE PRICE OF THE EQUIPMENT.
IN NO EVENT SHALL WSE BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, INCIDENTAL OR
SPECIAL DAMAGES OF ANY NATURE ARISING FROM THE SALE OR USE OF THE EQUIPMENT.
Some states do not allow limitations on incidental or consequential damages or on how long an implied
warranty lasts, so the above limitations may not apply. This warranty gives specific legal rights; however,
other rights which vary from state to state, may pertain.
Digital command key and magnetic stripe card warranties vary, according to the particular card used. See
the product literature.
The information in this manual is believed to be accurate and reliable. However, WSE assumes no
responsibility for any errors that may appear. Possession of this manual does not imply the granting of
licenses to make or sell equipment or software constructed according to descriptions provided.
P/N 6600025, Rev. D iii
DigiReader Series
Проектирование. Монтаж. Продажа. - http://vskd.ru
FEDERAL COMMUNICATIONS COMMISSION RADIO
FREQUENCY INTERFERENCE STATEMENT
This device complies with part 15, sub-part C of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
Regulatory labels are not attached at the factory. They are included in the ship-kit with
the PC-board and must be applied visibly to the enclosure (if purchased), or (if not)
to the back of the PC-board.
ivP/N 6600025, Rev . D
DigiReader Series WSE
Проектирование. Монтаж. Продажа. - http://vskd.ru
T able of Contents
COPYRIGHTAND TRADEMARK INFORMA TION .............................................................................................. ii
LIMITED WARRANTY ........................................................................................................................... iii
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT ................................. iv
The DigiReader Series is a family of Digital Proximity Readers (DigiReaders). (Graphic representations of the DigiReader Series —not to scale— are shown in figure 1, below, and figure 2, on page
5.) DigiReaders are bi-directional security devices that read digital credentials, (from either side of
the sensor), at ranges from 1 to 20 inches (2½ to 51 cm), depending upon the model and the
environmental conditions. DigiReaders are used with the NexSentry 4100, 4102, 4104, Star I and
Star II (4100 Series), SE818SC and SE422 Access Control Units (ACUs), with the ACUs either
operating as stand-alone devices or operating in conjunction with a StarGaze, a NexSentry Manager
(NSM), a NexSentry Command Center (NSCC), (an SE6000), or an SE5850, WSE Access Control
Host System. Connection between a DigiReader and an ACU is over the WSE proprietary S-Net
interface or over a Wiegand interface to a Wiegand ACU. (The Wiegand data can be either 26- or
34-bit Wiegand standard.) (Also included in the DigiReader Series is a keypad-only reader, the
DR4200K, which is the only family member available with the analog 818SX ACU.)
DR4201
CAUTION 1.
CAUTION 2. The information in this manual is not intended to conflict with the building codes,
P/N 6600025, R
DR4205K/DR4200K
DR4203
Figure 1: The Different DigiReader Models (Not to Scale)
Read this manual carefully before attempting to wire in place a DigiReader.
The warranty is void if damage occurs to the unit as a result of incorrect
wiring.
electrical codes, fire codes, or safety codes required for any given installation.
In all cases, the prevailing building codes must take precedence.
DigiReaders emit a low-level 140-kHz field. When a digital credential (card, KeyMate™, DuraTag™,
etc.) is placed in this field, a digital chip embedded in the credential uses the field’s energy for
activation. Once activated, the credential responds by broadcasting a 70-kHz signal, modulated
with a credential-specific code sequence, back to the reader. The reader receives this signal and
converts it to a digital code which is then sent to the ACU, (the Controller). The Controller identifies
the digital credential according to its code and makes either an access granted or an access denied
decision, based on credential information stored in the Controller's database or the host system's
database.
The DR4205K has a keypad on the face of the DigiReader. The keypad is used to enter the user’s
Personal Identification Number (PIN). The DR4205K keypad version can be configured for credentialonly use, or keypad-only use, or both, from the ACU DOOR Command. If the S-Net Reader Type
entry is set to DKR, the credential use will be activated for that door; set to NONE, the credential
use for that door will be de-activated; (– this is true for all DigiReaders except the DR4200K). For
the same door/reader combination, if the VIP Enable is set to Yes or No, the keypad portion will be
activated or de-activated, respectively.
DigiReader Series
The DR4200K is a keypad-only reader look-alike of the DR4205K, activated from the ACU DOOR
Command by setting VIP Enable (for that door) to Yes.
LED (AND BEEPER) OPERATION
LED (AND BEEPER) (S-NET OPERATION)
All DigiReaders have a single three-color (red-amber-green) LED controlled by the Access Control
Unit (ACU) to which the DigiReader is attached. Figure 2 shows the location of the LED on each
of the DigiReader models.
With the DigiReader on line to an ACU and with power applied, (the ready state), the DigiReader's
LED will be a constant red. When a DigiReader is configured to read digital credentials only (with
no keypad part of the DR4205K or VIP2 or DR4200K activated for the same door), a valid credential
will produce a momentary amber LED, followed by a green LED for the door unlock time or until the
door is closed following the credential-holder's access; (the LED will then return to the constant red).
With a keypad also activated, the amber LED will continue until either both the valid digital credential
and valid PIN, in either order, have been read/entered, producing the green unlock time LED, or until
the PIN grace period has been exceeded, producing the red LED. With only the keypad activated,
a valid PIN will produce the momentary amber, the unlock green and the return to the constant red.
4 P/N 6600025, REV. D
DigiReader Series
Проектирование. Монтаж. Продажа. - http://vskd.ru
The complete operational characteristics (LED and beeper behavior) for a DigiReader with or without
keypad, or with the keypad only used, are shown, (respectively), in Tables 2, 2A and 2B, below.
LED
LED
LED
LED
DR4205K/DR4200K
DR4201
DR4203
Figure 2: LED Locations for the Different DigiReader Models
NOTE: In each WSE security management system, the TUNE command (or its equivalent) is used
to specify LED and beeper behavior when a valid key is presented.