Wrought Studio W000611157 Assembly Instruction

Page 1
Chair
Hardware:
Component:
5
6
3
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through thi s leaflet and then follow the simple step-by-step instructions.
2. Owing to the size and weight of the chair, we recommend t hat it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approximat e assembly time: 25 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
5. Assemble all components loosely until advised t o tighten. Depending on use, it may be necessary to tighten the components from time to time, so please save t he tools that have been provided.
6. Please keep all fitting out of reach of children.
A. Bolt M8x60mm x 10
B. Flat Washer M8 x 10
C. Allen Wrench x1
1 Back Cushion x1 2 Seat Cushion x1 3 Back Frame x1 4 Left Arm x1
5 Right Arm x1 6 Seat Frame x1 7 Leg x4
Page 1 of 5
Page 2
HARDWARE
INSIDE
8
6
7
6
7
7
7
FRONT
BACK
Chair
STEP 1:
Please take the compressed Seat Cushions (2), Back Cushions (1), all Legs and hardwares bag from the bottom of Seat Frame (6). Carefully remove plastic packaging of the compressed Seat Cushions (2) and Back Cushions (1). Being carefully not to cut through to them. Place compressed Seat Cushions (2) and Back Cushions (1) on a flat surfac e in a well ventilated room and allow 48 hours for expansion. Due to the unique properties of the compressed Seat Cushions (2) and Back Cushio ns (1), dimensions after expansion will vary slightly; this is normal and will not affect the performance of your chair.
STEP 2:
Please put Sofa Frame (6) on a carpeted or padd ed surface. Insert Leg (7) to the bottom of Frame (6) and tight by hand in the direction of the arrow as shown. Repeat the same steps for the other 3 pieces of Leg (7).
Page 2 of 5
Page 3
A
x 4x 4
B
x 1
C
A
x 4x 4
B
x 1
C
4
FRONT
BACK
A
C
B
4
5
6
FRONT
BACK
Chair
STEP 3:
Attach Left Arm (4) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat Washers (B) as shown. Tighten Bolts (A) by using Allen Wrench (C) fully as shown.
Hardware & Tools required
STEP 4: Attach Right Arm (5) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pi eces of Flat Washers (B) as shown.
Tighten Bolts (A) by using Allen Wrench (C) fully as shown.
Hardware & Tools required
Page 3 of 5
Page 4
A
x 2
x 2
B
x 1
C
4
5
6
3
4
4
5
FRONT
BAC
K
Chair
STEP 5:
Slide the two cl ips of Back Frame (3) to the c lips of the side of the Left Arm (4), Right Arm (5) by hand in the direction of the arrow as shown.
STEP 6:
Insert 2 pieces of Bolts (A) with 2 pieces of Flat Washers (B) into the pre-drilled holes on Seat Frame (6) . Use Allen Wrench (C) to tighten Bolts (A) clockwise until secure.
Hardware & Tools required
Page 4 of 5
Page 5
6
2
1
Chair
STEP 7:
Put Back Cushion (1) and Seat Cushion (2) to the assembled chair as shown. Assembly is complete. Your Chair is ready to be used now!
Page 5 of 5
Page 6
SOFA USER GUIDELINE
This product makes a long journey to reach you and the cushion is compressed, please reshape the cushion to restore to its original beauty before using, steps as follows:
1.Carefully remove the plastic packing and put the cushion on a flat surface in a well ventilated room and allow 48 hours for expansion.
3.Press the back cushions with both hands from front side.
2.Press the back cushions with both hands from side edge.
4.Restoring action is complete,you can put it to the assembled sofa now.
Loading...