WORLD TECH ELITE 33061, ECHO Instruction Manual

ITEM NO. 33061

2

14

TABLE OF CONTENTS

INTRODUCTION

SAFETY & PRECAUTIONS

DRONE DIAGRAM

TRANSMITTER DIAGRAM

INSTALLING THE TRANSMITTER BATTERY

INSTALLING THE DRONE BATTERY

CHARGING THE DRONE BATTERY

SYNCING THE DRONE TO THE TRANSMITTER

TRANSMITTER LCD INTERFACE

FLIGHT CONTROLS

LIVE FEED CAMERA APP OPERATION

USING THE DRONE CAMERA

ADJUSTING THE TRIM

SPECIAL ACTIONS

POST FLIGHT

LOW VOLTAGE ALARM PROTECTION

REPLACING THE ROTORS

TROUBLESHOOTING

BATTERY DISPOSAL WARNINGS

NOTES:

3

3

4

4

5

5

6

7

7

8

9

FLIGHT CONTROLS - AUTOPILOT:TAKE OFF/LANDING

7

9

9

10

11

12

11

12

13

13

ATTACHING THE DRONE CAMERA

ATTACHING THE SMART PHONE CRADLE 5

ATTACHING THE SMART PHONE

5

3

INTRODUCTION

SAFETY & PRECAUTIONS

Thank you for purchasing this amazing World Tech Toys product. This drone is designed for outdoor
flight. Please carefully read the entire manual before operating this drone and keep it for reference in
the future.

1. Important Instructions

2. Safety Instructions

3. Flight Environment

3. Attention Before Flying

1) This product is not a toy. It is a precision piece of equipment with integrated mechanical
technologies, electronic, aero dynamics and radio frequencies. To avoid accidents, the
operator must read these instructions carefully, prior to operation. If operated incorrectly,
serious physical injury and/or property loss may occur.

2) This product is suitable for operators with previous hobby flying experience, age 14 and up.

3) Only fly in a safe environment that is legal for remote control flying.

4) We are not responsible for the operation and control of this device and related safety
responsibilities.

1) The minimum recommended flying area is 25ft x 25ft x 15ft.

2) Be sure that the transmitter and drone batteries are fully charged.

3) Be sure that the throttle is at its lowest position to avoid premature flight.

4) Always turn on the drone first, then turn on the transmitter. Incorrect operation may result in
failure and the possible influencing of other devices in area.

5) Ensure that all plugs and wires are secure and in place as they may loosen over time.

The inside of this drone is integrated with precision electronic and mechanical parts. Avoid
contact with water and wet environments as it may result in parts breakdowns and accidents
may occur.

1) Always operate far away from obstacles and crowds. This drone has uncertain flying speeds
and conditions which present potential danger. Fly away from people, animals, high buildings,
high voltage wiring, etc. To ensure a safe and fun flying environment avoid bad weather
conditions like wind, rain, and thunder.

2) Avoid high temperatures. This drone is made of metal, plastic, electronic components and
other materials. Keep away from any heat source and avoid using in high temperatures to
prevent transformation and broken parts resulting from the heat.

4

DRONE DIAGRAM

TRANSMITTER DIAGRAM

*Speed Control Modes:

• Low Speed: Transmitter beeps once.

• High Speed: Transmitter beeps twice.

NOTE: Drone starts in the Low Speed Mode.
Press the HIGH SPEED GEAR button to toggle.

Rotor

Landing Skids

HD Picture/Video Camera

Landing
Skids

LED

Lights

BOTTOM OF DRONE

Power

Switch

Battery
Compartment

Left/Right Trim Adjustment

Smart Phone

Cradle

Power Switch

A Return

Camera

Power Indicator

Auto Pilot

Rudder

HD Picture/Video

Camera Mount

Throttle

Video

Camera Fine

Tuning

Speed Control

Follow Me

Orbit

GPS Switch

Forward/Backward
Trim Adjustment

5

Battery Cover

4 AA Batteries

(NOT INCLUDED)

First remove the battery cover by sliding down. Next
install 4 AA batteries with the correct polarity. Finally
replace the battery cover.

Align the connectors of the battery pack to
the drone, then slide the battery pack into the
drone until a click is heard.

CAUTION:

1. Make sure the batteries are
installed with the correct polarity.

2. Do not mix old and new batteries.

3. Do not mix different types
of batteries.

INSTALLING THE TRANSMITTER BATTERY

INSTALLING THE DRONE BATTERY

Power Switch

Make sure the power switch on the battery
pack is in the OFF position and the drone is
free of debris.

ATTACHING THE SMART PHONE CRADLE

Align the Smart Phone Cradle with the
opening on top of the remote and slide in.

To attach smart device, pull up on the black
handle on top of the cradle and insert device
between foam protectors.

Battery
Compartment

ATTACHING THE SMART PHONE