WORLD TECH ELITE 33054, Rezo Instruction Manual
INSTRUCTION MANUAL
ITEM NO. 33054
2.4GHz 4.5CH RC RACING QUADCOPTER
TABLE OF CONTENTS
INTRODUCTION
SAFETY & PRECAUTIONS
DRONE DIAGRAM
TRANSMITTER DIAGRAM
INSTALLING THE TRANSMITTER BATTERY
INSTALLING THE DRONE BATTERY
CHARGING THE DRONE BATTERY
PREFLIGHT PREP / SYNCING THE DRONE TO THE REMOTE
CHANGING THE DRONES SHELL
FLYING THE DRONE - SPECIAL FUNCTIONS
ADJUSTING THE TRIM
POST FLIGHT
REPLACING THE ROTORS
RACING RINGS ASSEMBLY
RACING RINGS ASSEMBLY CONTINUED
3
3
4
4
5
5
5
6
6
8
FLYING THE DRONE 7
9
10
10
11
12
LANDING PADS ASSEMBLY
TROUBLESHOOTING
12
NOTES: 13
13
2
INTRODUCTION
SAFETY & PRECAUTIONS
Thank you for purchasing this amazing World Tech Toys product. This drone is suitable for indoor and
outdoor flight. Please carefully read the entire manual before operating this drone and keep it for
reference in the future.
1. Important Instructions
2. Safety Instructions
3. Flight Environment
4. Attention Before Flying
1) This product is not a toy. It is a precision piece of equipment with integrated mechanical
technologies, electronic, aero dynamics and radio frequencies. To avoid accidents, the
operator must read these instructions carefully prior to operation. If operated incorrectly,
serious physical injury and/or property loss may occur.
2) This product is suitable for operators with previous hobby flying experience, age 14 and up.
3) Only fly in a safe environment that is legal for remote control flying.
4) We are not responsible for the operation and control of this device and related safety
responsibilities.
1) The minimum recommended flying area is 25ft x 25ft x 15ft.
2) Be sure that the transmitter and drone batteries are fully charged.
3) Be sure that the throttle is at its lowest position to avoid premature flight.
4) Always turn on the drone first, then turn on the transmitter. Incorrect operation may result in
failure and the possible influencing of other devices in the area.
5) Ensure that all plugs and wires are secure and in place as they may loosen over time.
The inside of this drone is integrated with precision electronic and mechanical parts. Avoid
contact with water and wet environments as it may result in parts breakdowns and accidents
may occur.
1) Always operate far away from obstacles and crowds. This drone has uncertain flying speeds
and conditions which present potential danger. Fly away from people, animals, high buildings,
high voltage wiring, etc. To ensure a safe and fun flying environment avoid bad weather
conditions like wind, rain, and thunder.
2) Avoid high temperatures. This drone is made of metal, plastic, electronic components and
other materials. Keep away from any heat source and avoid using in high temperatures to
prevent transformation and broken parts resulting from the heat.
3
DRONE DIAGRAM
TRANSMITTER DIAGRAM
Power Light
Power Button
Flip Stunt ModeSpeed Modes
Turn Left/Right Trim
Ascend/Descend
(Turn Left/Right)
Forward / Backward
(Move Left / Right)
Forward / Backward Trim
Move Left / Right Trim
4
Headlight
BOTTOM OF DRONE
FRONT
BACK
Battery
Compartment
Rotor
Shell
Power
Switch
Rotor Guards
Landing Skids
Red LED
Lights
Green LED
Lights
Landing
Skids
Battery Cover
4 AA Batteries
(Not included.)
First remove the screw on
the battery cover and then
remove the battery cover
itself. Next, install 4 AA
batteries with the correct
polarity. Finally, replace the
battery cover and screw it
in place.
CAUTION:
1. Make sure the polarity of the
batteries are correctly installed.
2. Do not mix old and new
batteries.
3. Do not mix different types
of batteries.
INSTALLING THE TRANSMITTER BATTERIES
INSTALLING THE DRONE BATTERY
CAUTION WHILE CHARGING:
Do not charge with the batteries still installed. Do not charge the battery unsupervised. Do not immediately
charge after use. Do not overcharge the battery. Ideal charge time is 45-60 minutes. Overcharging can cause
a catastrophic failure. Always charge on dry and ventilated areas away from any heat source or flammable
materials. Always use the original USB charging cable provided. Promptly change and replace old or defective
batteries.
Battery Type Battery Specification Usage Duration Charge Time
BATTERY PACK SPECIFICATIONS
LiPo Battery 3.7V 380mAh Flight Duration 6 - 7 minutes Charging Time 45 -60 minutes
5
1 3
Connect the batteries power cable
to the drones power port as shown.
Test the drone by flipping the power
switch toward the front of the drone
body. The LED lights should turn on.
Make sure the drone is turned off by
flipping the switch on the side of the
drone towards the drones rear.
CHARGING THE DRONE BATTERY
Completely remove the battery from
the drone by sliding it out toward the
rear of the drone.
Connect the battery pack to the
included USB charger then plug the
USB to any powered USB port. The
USB Charger LED light will turn on
during charging and will turn off
once charging is complete.
Make sure the drone is turned off by
flipping the switch on the side of the
drone toward the rear. Disconnect
the battery power cable from the
drone power port as shown.
Insert the battery from the rear of
the drone into the space under the
drone shell. Make sure the battery
power cable is sticking out of the
back of the drone.
3
2
1
2
Loading...