Workrite Willow Dual Assembly Instructions
WillowTM Dual Assembly Instructions
M4 8mm Screw M4 12mm Screw
M4 16mm Screw Spacer
M4 8mm Screw M4 12mm Screw
M4 16mm Screw Spacer
M4 8mm Screw M4 12mm Screw
M4 16mm Screw Spacer
M4 16mm Screw Spacer
M4 8mm Screw M4 12mm Screw
M4 16mm Screw Spacer
Plastic Cap 7/32” Allen Wrench
1/8” Allen Wrench
Steel WasherPlastic Pivot Washer
M4 8mm Screw M4 12mm Screw
M4 16mm Screw Spacer
1/8” Allen Wrench
Steel WasherPlastic Pivot Washer
Important Safety Instructions
Read and understand all these safety instructions before using the product.
Do not mount the Desk Base of the Willow Arm on an unstable surface or any surface that could not mount the Desk
Base rmly.
During installation, beware of the recoil of the Willow Arm body when attaching or detaching the monitor to the Willow
Arm. To prevent damage or injury when changing the monitor, always raise the Arm to its highest position before the
monitor is detached. The Willow Arm can support monitors from 1 to 14 pounds.
Do not attempt to disassemble, service or modify the product.
Use only a slightly damp cloth to clean the Willow Arm surface. Never use ammable solvents like alcohol, benzene,
thinner, etc. on the product.
Parts grouped by package
Willow Arms Assembly
A
Qty: 1
Quick Release
B
Bracket
Qty: 2
M4x18 Phillips
C
Screws
Qty: 8
M4x12 Phillips
D
Screws
Qty: 8
M4x8 Phillips
E
Screws
Qty: 8
10mm Plastic
F
Pivot Cover Cap
G
3/16" Allen
H
Desk Base
I
Spacers
Qty: 8
Qty: 1
Wrench
Qty: 1
Qty: 1
Upper Clamp
J
Bracket
Qty: 1
Lower Clamp
K
Bracket
Qty: 1
¼" x 20 x ⅜"
L
Phillip Flat
Head Screws
Qty: 2
Plastic
T
Pivot
Washer
Qty: 1
Pivot
W
Pin
Qty: 1
⅜" x 16 x 3½"
M
Hex Bolt
Qty: 1
Plastic
N
Clamp Knob
Qty: 1
Plastic
O
Clamp Pad
Qty: 1
7/32" Allen
U
Wrench
Qty: 1
⅜” x 16 x 3½”
X
Button Head Allen
Cap Screw
Qty: 1
OR
WA2200-G-S only WA2200-C-S only
⅜” x 16 x 4½"
P
Threaded Stud
Qty: 1
⅜" Steel
Q
Washer
Qty: 1
⅜" x 16
R
Hex Nut
Qty: 1
U-Bracket
S
Qty: 1
⅛" Allen
V
Wrench
Qty: 1
⅜” Steel
Y
Washer
Qty: 1
#1500183 - Rev A
Verify that you have all the hardware and tools needed for the assembly
Check your packages against the parts list
on page 1 to verify that you have all the
parts needed.
Assemble Base
1
Clamp Mount: WA2200-C-S only
Assemble Clamp - Thread Hex Bolt (M) through Knob (N)
a
and Upper Clamp Bracket (J) and tighten securely. Press
the Plastic Clamp Pad (O) onto the end of the Bolt.
Mount Lower Clamp Bracket (K) to Desk Base (I) with
b
Screws (L) and tighten using a #3 Phillips Screw Driver.
Put Desk Base assembly onto work surface then slide
c
teeth of Clamp into Bracket slots. Use the highest slots
possible for best clamping. Turn knob to tighten.
You will also need the following tools:
#3 tip Phillips screwdriver
OR
Grommet Mount: WA2200-G-S only
Drill bolting hole in worksurface if needed. Put Desk Base (I)
a
directly on the bolting hole of worksurface and insert and tighten
the ⅜" x 16 x 4½" threaded Stud (P).
Place the U-Bracket (S) onto the Threaded Stud with the at bottom
b
of the U facing down.
a
O
J
N
M
b
I
K
L
c
I
P
a
Bolting
hole >⅜"
b
Place the ⅜" Steel Washer (Q) followed by the ⅜" x 16 Hex Nut (R)
c
onto the Threaded Stud and tighten securely.
2
Attach Willow Arms to Desk Base
Insert Pivot Pin (W) into Desk Base Assembly (I).
a
Put Plastic Pivot Washer (T) over Pivot Pin.
b
Put Arm Assembly (A) onto Pivot Pin.
c
Place Steel Washer (Y) onto Button Head Allen Bolt (X) and
d
install into the Arm assembly and base. Tighten with 7/32" Allen
Wrench (U) – be sure the arm is snug but rotates freely.
Tighten Set Screw in back of Desk Base with ⅛" Allen Wrench
e
(V).
Snap Pivot Cover Cap (G) into top of Arm Assembly.
f
e
R
c
G
U
Q
S
f
d
X
A
Y
c
T
W
b
a
I
V
2 Workrite Ergonomics 800.959.9675 www.workriteergo.com
Loading...