Assembly & Installation Instructions:
Solace Electric SOL-E-DT-B
Parts Included
Solace Electric Base
A
Qty: 1 B
Keyboard Platform
Qty: 1
Keyboard Platform
C
Bracket
Qty: 1
D
E
Single Monitor Mount
Qty: 1
M5×10 mm Allen
Head Screws
Qty: 4
M6×12 mm Allen
F
Head Screws
Qty: 4
M5 Allen wrench
G
Qty: 1
M6 Allen wrench
H
Qty: 1
Tools Required
5 mm & 6 mm Allen Wrenches included
#2 Phillips Screwdriver or Drill/Driver
Monitor Mount Kit
M4×24 mm Phillips
I
Head Screws
Qty: 4
M4×12 mm Phiips
J
Optional, Sold Separately
Caution! Do not exceed maximum (payload) weight limit
of 110 lb. This includes monitors, optional monitor brackets
Dual Monitor Bracket Triple Monitor Bracket
and all equipment on both surfaces.
1 Attach Keyboard Platform Bracket to Keyboard Platform
Attach the Keyboard Platform Bracket (C) to the Keyboard Platform (B) using
four 5M×10 mm Allen Head Screws (E) using the 5 mm Allen Wrench (G).
2 Attach Monitor Mount to the Solace Electric Monitor Arm
2.1 Attach the Single Monitor Mount (D) to the Monitor Arm on the Solace
Electric Base (A) using four 6M×12 mm Allen Head Screws (F) using the
6mm Allen Wrench (H).
Note: If you have purchased either the optional Dual Monitor or
Triple Monitor Brackets, attach them in the same fashion.
2.2 For taller users, an additional 3" of height can be achieved by
mounting the Single Monitor Mount (D) in the optional "Top
Mounting" position as shown.
Head Screws
Qty: 4
D
2.1
Monitor Arm
13 mm Spacers
K
Qty: 4
E
B
Shown upside-down
F
Optional Top Mounting
C
Bottom
2.2
A
Optional Triple Monitor BracketOptional Dual Monitor Bracket
1 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Single Monitor Bracket
3 Plug in Solace Electric Base to Wall Power & Raise
3.1 Plug in the Solace Electric Base (A) into 110 V power.
3.2 Raise the unit to its highest level by pressing the UP (+)
arrow until the worksurface reaches its highest level and
stops. The display should read "58" mm.
Note: Go to www.workriteergo.com/instructions and find
Solace Electric Control User Guide for instructions on how
to change from centimeters to inches.
3.2
Up Button
4 Install the Keyboard Platform
3.1
4.1 Unlock the Keyboard Platform Clamps on the bottom of the Worksurface by pivoting down.
4.2 Insert the Keyboard Platform assembly into the channels in the bottom of the Solace Electric Base Worksurface
until the Keyboard Platform Bracket (C) is flush with the front of the Worksurface.
4.3 Lock the Keyboard Platform Bracket in place by pivoting the Keyboard Platform Clamps up.
Unlock From Below
Lock From Below
2 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
5 Mount Monitors to VESA Plate
If possible, use the Monitor Mount screws from your Monitor
to attach your monitor to the VESA plate. Otherwise use the
shortest screws possible from the included hardware kit (I or J)
Use Spacers (K) for recessed monitor mounts.
Note: Mounting on the optional Dual or Triple Monitor Mounts is
performed in the same fashion.
100 mm VESA standard,
use 4 outer corner holes.
75 mm VESA standard,
use 4 inner corner holes.
I
KJ
Important Note: It is strongly recommended to use
the mounting screws provided by the monitor manufacturer
if possible. If longer screws are required, use the shortest
screws possible and Spacers to avoid damage to the monitor.
Single Monitor Shown
6 Consult the User Guide for your Electric Switch
Go to www.workriteergo.com/instructions to find Solace Electric Control User Guide for instructions on how to
set up this product for ideal ergonomic benefit.
3 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
4 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
1500408 Rev B
Loading...