Workrite RISE-2E-3044-X, RISE-2E-4674-X, RISE-2E-7694-X Assembly And Installation Instructions

Assembly & Installation Instructions:
Rise Quiet 2-Leg Electric Workcenter
RISE-2E-3044-X, RISE-2E-4674-X, RISE-2E-7694-X

Two Leg Frameset, Components & Hardware

A

Legs

Qty: 2

Feet

B

Qty: 2 C

Frameset

Qty: 1 E

Side Bars

Qty: 2

Switch

Qty: 1D

3.5 mm × 16 mm Phillips

F

Head Wood Screw
Qty: 2

Power Supply*

G

Qty: 1

*A second Power Supply may be added
to this system as a separate purchase.

Silence Kit 1 Cable Mgt. Kit 1Collision Detection System (CDS) Kit

20 mm Foam Washers

K

Qty: 12 N

16 mm Steel Washers

L

Qty: 6

#8 × 1" Phillips Pan

M

Head Wood Screws
Qty: 6

Hardware Kit 1

-18 × " Button Head

T

Socket Cap Screws
Qty: 4

-18 × 1" Flat Head Socket

U

Cap Screws
Qty: 8

Power Supply Bracket

Qty: 1 J

Collision Detection

Sensor
Qty: 1

#8 × ½" Self Tapping

O

Phillips Head Screws
Qty: 2

#8 × ¾" Phillips Pan

P

Head Wood Screw
Qty: 1

-20 × " Flat Head

V

Phillips Screws
Qty: 4

#8 × 1" Phillips Pan Head

M

Wood Screws
Qty: 8

Leg Cable

I

Qty: 1H

" P-Clips

Qty: 6

#6 × ⅝" Phillips Flat

S

Head Wood Screw
Qty: 6

Round Bumpers

X

Qty: 2

#10 × 2½" Phillips Pan

W

Head Wood Screws

Qty: 6

Round Bumpers

X

Qty: 8

Power Cable

Qty: 1

" P-Clips

Q

Qty: 2R

" P-Clips

R

Qty: 6

#6 × ⅝" Phillips Flat

S

Head Wood Screw
Qty: 8

Square Bumpers

Y

Qty: 2

Zip Ties

Z

Qty: 2

Round Plugs

D

Qty: 24D

Required & Sold Separately

Worksurface

Note: If you are assembling a 3-Leg Frameset, use instructions in the Third Leg Framset for complete assembly
instructions.

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 12

WARNING: Maximum loading of frameset is 265 lb. (120 kg.). Maximum load includes the weight of the table top

itself, any equipment placed upon it, and any equipment suspended or hanging under it. Loading should be evenly distributed over table
surfaces.

Rise 2-Leg

V = 120 VAC, 60 Hz

3.2 A maximum with single power supply
Duty cycle: 1 minute on/ 9 minutes o.

IMPORTANT SAFETY INSTRUCTIONS:

When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Rise Quiet Frameset.

DANGER: To reduce the risk of electric shock, always unplug this Rise Quiet Frameset from the electrical outlet before cleaning.

CAUTION-RISK OF ELECTRIC SHOCK. This unit may have two power cords. Unplug both cords before moving or servicing this

furnishing.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Unplug from outlet (or outlets if equipped with a second power supply) before putting on or taking o parts, moving or servicing.

2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.

3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.

4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into
water. Return the furnishing to a service center for examination and repair.

5. Keep all cords away from heated surfaces.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, remove plug from outlet (or outlets if equipped with a second power supply).

9. Each Rise Quiet Frameset intended to support an equipment payload capacity of 265 lb. (120 kg.).

SERVICING OF DOUBLE-INSULATED PRODUCTS

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double­insulated product, nor is a means for grounding to be added to the product. Servicing a double-insulated product requires extreme care and
knowledge of the system, and is to be done by a qualified service personnel. Replacement parts for a double-insulated product must be identical
to the parts they replace. A double-insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol
(square within a square) is also able to be marked on the product.

FOR COMMERCIAL USE ONLY

SAVE THESE INSTRUCTIONS

Verify that you have all the hardware and tools needed for the assembly

✓

Check your cartons against the list above to verify that you have all the parts needed.

You will also need the following tools:

Drill/driver with #2 Phillips head bit
" Allen bit for drill/driver
or " Allan Wrench (Z) provided

If you do not have a Workrite pre-drilled worksurface, you will also need:

⅛" drill bit
Tape measure

An electric Drill/Driver is
recommended over hand
tools for this installation.

2 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Layout Components in Assembly Area

1

Assemble near final installation location. Once the Workcenter is built it requires at least two people to li and
move into place. You'll need a large and clean area to assemble. Check your packaged contents against the parts
list on page 1 to verify that you have all the parts needed.

If you have a Workrite Pre-Drilled Worksurface, it may be easiest to assemble on the bottom of the worksurface,
using the pre-drilled holes as a guide.

Place Legs (A), Feet (B), Framesets (C) and Side Bars (D) on the floor or bottom of your worksurface.

Set the Switch (E), Collision Detection Sensor (N) packaged separately, and Power components (G,H,I & J) within
easy reach.

Carefully unpack and arrange all hardware.

Note! You will have many pieces in common and some VERY SIMILAR parts in the Silence Kit, Collision Detection
Kit,Cable Management and Hardware Kit. Use caution!

A

A

D

C

I

B

B

G

Two Leg Frameset Hardware CDSSwitch

K

L

M

Q

R

S

DD

J

D

H

E

T

U

V

M

W

X

Y

F

O

P

R

S

X

N

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 12

Z

2

Attach Side Bars & Bumpers to Underside of Framesets

Attach Side Bars (D) to Frame Assembly with

a

¼-20 × ⅝" Flat Head Phillips Cap Screws (V).

Hardware at actual size

-20 × " Flat Head

V

Socket Cap Screw

Apply the six Round Bumpers (X) at mount

b

location on the Frameset as shown. Apply
the Square Bumper (Y) at the Joining Bracket
location just to the side of the center hole.

Hardware at actual size

Round Bumpers

X

Hardware at actual size

Square Bumpers

Y

a

To avoid stripping the threads, always insert and make
the first few turns of the screw BY HAND with the provided
Allen wrench, ensuring it is in straight.

V

C

D

X

Y

b

Joining Bracket

4 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Attach Framesets to Legs

3

Flip the Framset over so the Bumpers and Side Bars
will rest on the Worksurface.

Loosen the Joining Bracket on the Frameset at

a

locations shown with the Allen head bit or wrench.

NOTE! Loosen frameset but do not disassemble!

Move the internal Joining Brackets out of the way to

b

allow attachment of legs. Keep frameset loose.

With frameset Joining Bracket still

c

loose, attach the two legs to the
frameset using eight -18 × 1" Flat
Head Socket Cap Screws (U).

Hardware at actual size

-18 × 1" Flat Head

U

Socket Cap Screw

Joining Bracket

A

a

A

c

a
b

U

C

c

Joining Bracket

Make sure Framseset is oriented
with "knee saver" area towards user

To avoid stripping the threads, always
insert and make the first few turns
of the screw BY HAND with provided
Allen wrench, ensuring it is in straight.

4

Attach Feet to Legs

Attach both Feet (B) To Legs (A) using four -18 × " Button
Head Socket Cap Screws (T). Make sure to use the correct
BUTTON HEAD Screws!

Note: Make sure the longer section of the foot will face the front
of the desk.

Tighten Securely.

Hardware at actual size

-18 × " Button Head

T

Socket Cap Screw

Make sure longer end of
foot is facing front of desk

U

T

B

Side Bar (D)
facing down

A

CAUTION! Be sure to use the correct
hardware for this step!

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 12

Expand Framesets to Correct Length

5

With Legs & Feet secure but the frameset Joining

a

Bracket still loose, extend the frameset out towards
the edge of the worksurface.

If you have a Workrite pre-drilled Worksurface:
Align frameset holes with pre-drilled holes in the

b

undersides of the worksurface.

Adjust Joining Brackets so center bracket hole aligns

c

with the center hole location.

Proceed to Step 6.

If you have a non- Workrite top:

Align frameset parallel with the back of the

b

worksurface.

Position frameset 7.2" from rear of Worksurface and

c

extend frameset until the Side Bars (D) are about

1.5"–2" from the ends of the top.

Adjust Joining Brackets so center bracket hole is

d

centered between framesets.

Proceed to Step 7.

Note: Avoid trip or tip hazards!
For uniquely shaped, non-standard
worksurfaces, it is the installers
responsibility to position the
worksurface to minimize extended
overhangs and position feet fully
under the worksurface.

Adjust Joining Brackets
so middle hole aligns
with screw location.

c

a

b

Adjust Joining
Brackets so middle
hole is centered.

d

D

D

b

1.5"– 2"

7.2"

c

6 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Attach Frameset to Workrite Pre-Drilled Worksurface

6

If you do not have a Workrite Pre-drilled Worksurface, skip to Step 7.

With Frameset positioned correctly from Step 5, carefully li Frameset (C) to place the Power Supply Bracket (H)

a

under the Frameset at location shown.

Carefully li the Frameset to place seven 20 mm Foam Washers (K) at all frame mount locations UNDER the

b

frameset as shown. Be sure to keep frameset aligned with pre-drilled holes.

Attach the Side Bars (D) to the worksurface using four of the 16 mm Steel Washers (L), four 20 mm Foam Washers

c

(K) and four #8 × ¾" Pan Head Phillips Wood Screws(M).

Attach the Frameset assembly with two 16 mm Steel Washers (L), three Foam Washers (K) and three of the

d

longer  × 2⅛" Flat Head Phillips Wood Screws (W). NOTE: No 16 mm Steel Washers (L) and only one BOTTOM
Foam Washer (K) are used in the Joining Bracket center frame location.

With frame securely fastened to the worksurface, re-tighten the Joining Brackets loosened in Setp 3a.

e

Proceed to Step 8.

W

e

K

M

L

K

K

L

C

c

W

e

C

K

c

C

d

D

K

c

K

located between

frameset and worksurface

Hardware at actual size

#8 × ¾ Phillips Pan Head

L

Wood Screw

NOTE
Attaches Side Bars (D) to Worksurface.

Hardware at actual size

#10 × 2½" Phillips Pan Head Wood Screws

V

a

Joining Bracket
location, bottom Foam
Washer (J) only.

Retighten

e

Hardware at actual size

20 mm Foam Washers

K

H

K

located
between frameset
and worksurface

b

NOTE
Attaches Frameset (C) to Worksurface.

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 12

7

1.5"– 2"

1

3

4

5

6

7

2

9

10

11

12

8

>¾"

Attach Frameset to Non- Workrite Top

With Frameset positioned correctly from Step 5, use a ⅛" drill bit to drill pilot holes in the seven frameset

a

mounting locations shown.

You may wish to mark your drill bit so you do not drill any more than ¾" deep to avoid damaging your
worksurface top. Do not drill all the way through worksurface!

With frame set positioned over pilot holes, li Frameset (C) to place the Power Supply Bracket (H) under the

b

Frameset at location shown.

With frame set positioned, li Frameset (C) to place twelve 20 mm Foam Washers (K) at all frame mount

c

locations UNDER the frameset. Be sure to keep frameset aligned with pilot holes.

Attach the Side Bars (D) to the worksurface using four of the 16 mm Steel Washers (L), four 20 mm Foam Washers

d

(K) and four #8 × 1" Pan Head Phillips Wood Screws(M).

Attach the Frameset (C) with two 16 mm Steel Washers (K), four Foam Washers (J) and three of the longer  ×

e

2⅛" Flat Head Phillips Wood Screws (V). NOTE: No 16 mm Steel Washers (K) and only one BOTTOM Foam Washer
(J) are used in the Joining Bracket center frame location.

Mark

d

a

Mark drill bit so you do not

>¾"

2

3

1

4

5

6

7

drill through your top

W

W

e

K

M

L

K

K

D

c

K

L

e

C

C

c

K

c

H

C

b

K

located between

frameset and worksurface

8 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Joining Bracket
location, bottom Foam
Washer (K) only.

K

located between

frameset and worksurface

8

Attach Collision Detection Sensor to Frameset and
Worksurface

Attach the two Round Bumpers (X) to the contact surface of the

a

Collision Detection Sensor (N).

Place the bumpers down, contacting the worksurface and position on Frameset (C) as shown. Attach Collision

b

Detection Sensor (N) to worksurface with one #8 × ¾" Phillips Head Wood Screw (P).

Attach the Collision Detection Sensor (N) to the Frameset (C) using the two #8×¾" Self Tapping Screws (O). You

c

will need to apply pressure with the screw in place to make the "bit" of the screw drill into the frame then catch
to attach and hold secure.

Note: For larger framesets, it may be necessary to mount the Collision Detection Sensor at an alternative
location on the frame, closer to the switch location.

X

N

P

b

Improper installation of the Collision
Detection System may result in false
collision incidents. Please follow
instructions closely.

Alternative location

a

C

N

c

CDS mount location

Hardware at actual size

#8 × ½" Self Tapping

O

Phillips Head Screw

Hardware at actual size

#8 × ¾" Phillips Pan

P

Head Wood Screw

9

Install Switch

Install your Switch (E) using two 3.5mm×16 mm
Pan Head Screws (F).

If you have a Workrite pre-drilled Worksurface:

Locate the pre-drilled holes near the front edge of
the Worksurface and attach.

If you have a non-Workrite top:
Align the switch with the front edge of the top, use a
⅛" drill bit to drill pilot holes using the Switch holes
as a guide and attach.

O

c

Use Self Tapping Screws
to drill into frame.

F

E

C

N

Do not drill all the way through worksurface!

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 9 of 12

Alternative location

Route and Connect Cables

10

Connect Switch (E) to closest Leg (A).

a

Connect Leg Cable (I) from one Leg (A) to the other Leg (A).

b

Connect Collision Detection Sensor (N) to Switch (E).

c

A

E

Connect Power Supply cable (G) to closest Leg (A).

d

Plug Power Cord (J) into the Power Supply (G).

e

a

A

c

N

I

b

d

To Leg (A)

G

J

To Power

G

J

Plug in

e

10 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

J

G

A

11

Attach Cables to Worksurface With P-Clips

Attach the P-Clips (Q & R) with #6 ×
⅝" Phillips Head Wood Screws (S) at
convenient locations to keep cables
up and out of the way being sure to
rout the cables through the Clips prior
to attaching to the underside of the
worksurface.

Note: the larger " P-Clips
(Q) are used on the Leg Cables
(I) in locations 6 & 7 and the
smaller " P-Clips (R) are
used on all other cables.

1

2

6

3

4

R

5

7

Q

I

Insert Round Plugs

12

Insert the Round Plugs
(DD) into corrosponding
Frameset holes as shown.

DD

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 11 of 12

13

Put Workcenter Upright and Plug In Power Cord

Turn the workcenter over into an upright position. Use at least two people to flip

a

over and position the workcenter.

Plug the Power Cord (J) into the power outlet.

b

a

J

Flip Workcenter on
its SIDE or BACK so
you do not damage
the switch.

Adjust Leveling Guides

14

If necessary, adjust leveling guides on table feet to level the worksurface.

15

Initialize Legs

Aer all components are connected, and the power cord has been plugged
in, the Legs need to be initialized.

Press and hold the UP and DOWN arrows on the Switch for at least 8 seconds.

a

Release both buttons and immediately press the DOWN arrow. The display will show three dashes and a home

b

icon in the lower le of the display as the worksurface moves to its lowest position.

b

You must complete this
initialization step or your
workcenter will NOT
function properly!

Once the worksurface stops moving, release the button and the three dashes will be replaced with the height

c

reading. The Legs are initialized and the Workcenter is ready to use.

Download the Rise Programmable Control User Guide

16

To get the full ergonomic benefit of this Workcenter, download the Rise Programmable User Guide. It contains
detailed information on set up and programming of your Rise Workcenter Programmable Control.

http://workriteergo.com/support/rise-control

Cleaning Instructions

✓

To clean the legs, apply cleaner to a so cloth.

Suggested cleaners: Windex or Formula 409.
Do not use solvents and do not saturate or spray cleaners directly onto workcenter base.

Parts & Accessories

✓

Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf for
replacement parts.

12 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

#1500359 - Rev B