Workrite Poise™–Dual
Assembly Instructions
Clamp and Grommet Mounts
#1500141 - Rev A
Workrite Poise–Dual™ Installation Instructions
Important Safety Instructions
Read and understand all these safety
instructions before using this product.
Do not mount the clamp base or the grommet base on an unstable surface
(any surface that will not hold the base rmly).
For safety reasons, the internal gas-strut of the Workrite Poise–Dual™ is
pre-adjusted at the factory to the lowest force for the prevention of arm
body recoil during installation.
IMPORTANT SAFETY PRECAUTION:
During installation, beware that the arm body can move suddenly when
attaching or detaching the LCD monitor to the Swing. WHEN CHANGING
THE LCD MONITOR, ALWAYS RE-ADJUST THE GAS STRUT TO THE LOWEST
FORCE SETTING. Without this adjustment, the arm will move suddenly upward when the monitor is removed.
Do not attempt to disassemble, service or modify the product yourself.
Use only a slightly damp cloth to clean the Arm surface. Never use ammable solvents like alcohol, benzene, thinner, etc.
Table of Contents
List of Parts .................................................................................................. 3
Step 1: Verify that you have all the hardware and tools needed for the assembly ... 4
Step 2: Attach Clamp Base to Work Surface ...................................................... 4
Step 3: Attach Grommet Base to Work Surface .................................................. 5
Step 4: Attach Monitor Arms to Monitors .......................................................... 5
Step 5: Attach Pivot Base and Arms ................................................................. 6
Step 6: Vertical Movement Adjustment ............................................................. 7
Step 7: Ball-joint Adjustment for Tilt Action ...................................................... 7
Step 8: Final Touches: Cable Management ........................................................ 8
2 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Poise–Dual™ Installation Instructions
List of Parts, grouped by carton
For model #: PA2000-C-_
Clamp Base
A
Qty: 1
Base Cushion
C
Qty: 1
M2.5 Hex Wrench
E
Qty: 1 F
B
M5 Hex Wrench
D
Qty: 1
Button head cap screw
M8 X 1.25 X 15mm
Qty: 2
Clamping Bracket
Qty: 1
14" Pole
M
Qty: 1
Cable manager
N
Velcro® strips
Qty: 2
Plastic Spacer 30mm
P
OD, 18.5 mm ID
Qty: 2
Button-head Cap
R
Threaded Bolt M8 X
1.25 X 70mm
Qty: 2
Dual Mount Clamp
O
Qty: 1
Pivot Pins 55mm
Q
Qty: 2
Set Screws
S
M5 X .8 X 10mm
Qty: 2
OR
For model #: PA2000-G-_
Grommet Base
G
Qty: 1
M8 Washer
I
Qty: 1
M8 X 1.25
K
Wing Nut
Qty: 2
M5 Hex Wrench
D
Qty: 1
U-Bracket
H
Qty: 1
M8 X 1.25 X
J
130mm Thread Rod
Qty: 1
Base Cushion
L
Qty: 1
M2.5 Hex Wrench
E
Qty: 1
M8 Disc Spring
T
Washer 23mm OD,
8.2 mm ID
Qty: 2
Assembled Arm
V
Qty: 2*
End Cap
W
Qty: 2*
Round-head screw
Y
M4 X 0.7 X 6mm
Qty: 8*
Flat M8 Washer
U
16mm OD
Qty: 2
Round-head screw
X
M4 X 0.7 X 10mm
Qty: 8*
Plastic Holding Tabs
Z
Qty: 16*
* Note that there are two of these cartons.
Quantities given show total from both cartons.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3
Workrite Poise–Dual™ Installation Instructions
Verify that you have all the hardware and tools needed for the assembly
1
Check your cartons against the list on page 2 to verify that you have all the parts needed.
You will also need the following tools:
#3 tip Phillips screwdriver
Clamp Base Only: Attach Clamp Base to Worksurface
2
For Grommet Base please skip to Step 3.
Attach the base cushion to the underside of the
a
base.
Attach 14” pole to base, securely tighten 4 set
b
screws (already in place).
Attach the clamping bracket to worksurface with 2
c
button-head cap screws. (See note below.) Use the
upper set of holes on the bracket for work surfaces
between ½" and 1¼" thick, and use the lower set for
work surfaces between 1¼" and 2¼" thick.
Tighten the clamping bracket until it is rmly
d
clamped to the work
surface.
Skip to step 4.
F
d
b
M
E
a
C
c
A
B
If there is not enough clearance to t the assembled base between
the back of the worksurface and the wall, place the clamp base on the
desk edge before attaching the clamping bracket from below.
4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Poise–Dual™ Installation Instructions
Grommet Base Only: Attach Grommet Base to Work Surface
3
Remove the center hole from the base cush-
a
ion, then attach it to the underside of the base,
aligning the hole in the base with the hole in the
protector. Thread the M8 Thread Rod into the
bottom of the base.
Attach 14” pole to base, securely tighten 4 set
b
screws (already in place).
Place the base on the work surface, centering it
c
over a bolting hole from 3/8” to 3” in diameter.
Position the U-Bracket and Small Washer onto
d
the M8 Thread Rod and secure the bracket by
tightening the Wing Nut.
b
E
M
Proceed to step 4.
Attach Monitor Arms to Monitors
4
Place monitor carefully on a clean, at
surface, face down.
G
L
a
c
J
H
I
K
d
Attach the monitor arm to the back of the
monitor with four screws, using a Phillips-
head screwdriver (not included). Use the
mounting screws provided by your monitor manufacturer if available. Otherwise,
use the screws provided that best ts
your monitor.
Use the outer holes for a
100mm mount, or the inner holdes for a
75mm mount.
Repeat for the second monitor.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5
X or Y
V
Workrite Poise–Dual™ Installation Instructions
Attach Pivot Base and Arms
5
Place the pivot pins and the large plastic spacers onto the dual mount clamp.
a
Place the dual mount clamp assembly onto the pole with the ratchet handle facing the back. Posi-
b
tion the mount so that the top of it is approximately 7” from the desk for a 15” monitor, 8” for a
17” monitor or 9” for a 19” monitor. Tighten the dual mount using the ratcheting handle. Pull the
handle out to release and rotate to allow for additional turns to tighten.
Attach one assembled monitor arm to the dual mount clamp. Position the arm horizontally and test
c
the height range to be sure it is correct for your monitor. If not, remove the arm and move the dual
mount clamp accordingly. Then replace the arm. Attach the second arm to the dual mount clamp.
Remove the monitor arms before
adjusting the clamp height to avoid
scratching the nish of the pole.
Secure the monitor arms by placing the small at washer on the 70mm threaded bolt, followed by
d
the larger disc spring washer, with the concave side facing away from the bolt head (down), and
then placing the bolt with the washers into the hole on the end of the monitor arm, tightening with
the M5 hex wrench. Tighten to a light friction so that the arm can turn, but not too loosely.
Install and tighten the set screws in the dual mount with the M2.5 hex wrench to lock the 70mm
e
bolts.
Press the end caps onto the ends of the monitor arms, covering the 70mm bolts.
f
f
W
R
d
U
T
V
c
Q
P
S
O
a
e
b
6 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Poise–Dual™ Installation Instructions
Loosen
Tighten
Tension
screw
90°
Adjustment
Screw
Vertical Movement Adjustment
6
If your monitor is too light or too heavy for the factory-set tension,
the arm will raise or lower too easily (or even on its own). If this is the
case, you need to adjust the vertical movement.
Set the monitor arm at a 90° angle and locate the adjustment screw on
a
the top of the arm joint.
If the arm tends to rise, turn the adjustment screw clockwise using the
b
M5 hex wrench, decreasing tension until the arm reaches a stable, balanced adjustment.
If the arm tends to drop, turn the adjustment screw counterclockwise
c
using the M5 hex wrench, increasing tension until the arm reaches a
stable, balanced adjustment. With too much tension on the arm, the
arm will tend to rise.
To prevent damage to the arm,
remove the hex wrench after
adjustment.
a
b
c
7
Adjustment for Tilt Action
If the monitor doesn’t hold its tilt position or
is too hard to tilt, adjust the screw directly
behind the LCD screen with the M5 Allen
wrench provided (clockwise to tighten,
counter-clockwise to loosen).
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7
Workrite Poise–Dual™ Installation Instructions
Workrite
Ergonomics
Strip
Strip
Final Touches: Cable Management
8
Thread monitor cables through Cable Mount located on underside of Forearm.
a
Place Holding Tabs in center slot as shown and slide into place along Mount track. Use four tabs on
each side.
Secure attached hook and loop strips around monitor
b
cables, again leaving enough slack at both ends of the
arm for full movement of the arms.
Attach the monitor cables to the pole and secure with the
c
Velcro® straps, again leaving enough slack between the
extension arm and the pole for full movement of the arm.
S
a
b
O
Replacement Part Numbers
6400443: Poise Arm W/O Base Type 1/5-15 Lb Graphite
6400441: Poise Arm W/O Base Type 1/5-15 Lb Silver
6400444: Poise Arm W/O Base Type 2/10-22 Lb Graphite
6400442: Poise Arm W/O Base Type 2/10-22 Lb Silver
6400364: Dual Arm Pole Mount – Graphite
6400363: Dual Arm Pole Mount – Silver
SASP-B: Pole 14” W/Cover Cap – Black
6400365: Pole 14” W/Cover Cap – Silver
SACB-B: SA Clamp Base Kit, Graphite
SACB-S: SA Clamp Base Kit, Silver
SAGB-B: SA Grommet Base Kit, Graphite
SAGB-S: SA Grommet Base Kit, Silver
c
8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Loading...