Workrite LOS3-B-M11, LOS3-B-M21 Assembly Instructions

Assembly Instructions: Manual, Single User

CAUTION !

Product is spring loaded and may open with extreme force when screw is removed.

MISE EN GARDE !

Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.

¡

ATENCIÓN !

Éste producto està cargado con resortes y puede abrise con extrema fuerza cuando

se remueve éste tornillo.

Workstation Chassis: LOS3-B-M11-XX-XX-XX-X

Parts Included:

Line of Sight Single

A

User Manual Chassis
Qty: 1

36" model shown

Chassis Hardware Kit: 4435564

Le Top Bracket

B

Qty: 1 C

"-18 Serrated

D

Flange Nut
Qty: 4

⅜-16 x 1" Flange

K

Head Cap Screws
Qty: 4

G

Right Top Bracket

Qty: 1

Lid Stop

Qty: 2

H

⅜" Glides

L

Monitor Mount & Wiring Hardware Kit, Manual: 4435563

VESA Mount

M

Qty: 1

M4 × 10 mm Monitor

P

Screw
Qty: 4

#10 Zinc Washer

S

Qty: 4 T

¼"-20 × ½" Allen, Button

Head Screw
Qty: 2

M4 × 16 mm Monitor

Q

Screw
Qty: 4

Cable Clips

Qty: 3

Cable Ties

U

Qty: 5

Plastic Spacers

O

Qty: 4N

M4 × 25 mm Monitor

R

Screw
Qty: 4

Wire Loom, 1" × 2'

V

Qty: 1

#10-¾" Phillips

Pan Head Screws
Qty: 30

Qty: 4

Foot Kit

Le Foot

I

Qty: 1

Right Foot

J

Qty: 1

Worksurface & Monitor Bay Lid

Worksurface

E

Qty: 1 F

Manual Monitor

Bay Lid
Qty: 1

Optional, Sold Separately

Ganging Brackets, Filler Channels, Back
to Back End Panels, Power System
Components, CPU Holders

CAUTION: Manual Li models are spring loaded
and require extra care until a monitor has been
installed. Follow all warnings and cautions.

✓

Verify That You Have All The Tools Needed For The Assembly

You will need the following tools:
Drill/driver or Phillips screwdriver with #2 tip

" or 4mm Allen wrench

½" Open ended wrench

" Open ended wrench

Product is spring loaded and may open with extreme force when screw is removed.

Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.

Éste producto està cargado con resortes y puede abrise con extrema fuerza cuando

CAUTION !

MISE EN GARDE !

¡

ATENCIÓN !

se remueve éste tornillo.

or

CAUTION!

Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.

MISE EN GARDE !

Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.

¡

ATENCION!

No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.

PUSH HERE TO RAISE OR

LOWER THE MONITOR

Caution: Spring loaded mechanism.

Exercise caution when cycling up or down!

1 of 8 Line of Sight | [phone] | los.workriteergo.com

1 Remove Front and Rear Panels, Set Power Cord Aside

1.1 Remove the Front and Rear Panels from the Chassis (A) by

turning the Panel Locks a quarter turn towards the center
of the panel (inward), then pivot the panels forward to
remove.

If you have Locking Panels, unlock using the included key.

Panel
Lock

Rear
Panel

1.1

1.2 Keep the protective tape around panels and on frame

until assembly is complete to protect finish.

Removable Panel Locking Panel

2 Attach Top Brackets

Attach the Le Top Bracket (B) and Right Top Bracket
(C) to Chassis (A) with the four "-18 Locknuts (D).
Threaded studs on the brackets insert through holes in
the Chassis and are held in place with the Locknuts.

Hardware at actual size

"-18 Serrated Flange Nut

D

A

1.1

Front
Panel

B

D

D

1.2

C

Protective
tape

Threaded
Studs

C

Under Top Bracket

3 Attach Lid Stops to Worksurface

Note: Build Assembly in a large, clean area on carpeting or

moving blankets to prevent damaging Worksurface and Lid.

G

E

H

3.2

3.1

F

3.1 Place Worksurface (E) and Monitor Bay Lid (F) upside down on
floor. Slide Monitor Bay Lid (F) into cutout in Worksurface (E).

3.2 Attach both Lid Stops (G) with eight #10-¾" Phillips Pan Head
Screws (H).

Hardware at actual size

#10-¾" Phillips Pan

H

Head Screws

2 of 8 Line of Sight | [phone] | los.workriteergo.com

4 Flip Chassis Upside Down Onto Worksurface

4.1 Place the Worksurface and Monitor Bay Lid

upside down on the floor and slide the Monitor

Monitor
Bay Hinge

Bay Lid into the cutout in the Worksurface.

4.2 Flip the Chassis assembly upside-down onto the
bottom of Worksurface

Use at least two people to flip over and position

the Chassis.

4.3 Align Chassis assembly so holes in Top Brackets
line up with pre-drilled holes in Worksurface and
holes in Monitor Bay Hinges line up with pre­drilled holes in Monitor Bay Lid.

Worksurface

5 Mount Chassis Assembly to Worksurface and Monitor Bay Lid

5.1 With Chassis Assembly correctly positioned on Worksurface, attach

Chassis Assembly to Worksurface with eight #10-¾" Phillips Head Screws
(H), four screws per Top Bracket (B & C).

4.2

4.3

Monitor
Bay Lid

4.1

5.2 Note: Chassis models over 48" have a Center Support which requires two

#10-¾" Phillips Head Screws (H) into the Center Support.

5.3 Attach Monitor Bay Lid to both Monitor Lid Hinges with two
#10-¾"Phillips Head Screws (H) per hinge at the forward location. You will
finish installing the hinges in Step 10 when workcenter is right side up and
you can more easily access the two other hinge screw holes.

Note: Monitor Bay Lid will
have approximately .2" of
clearance around the cutout in
the Worksurface when properly
installed.

Hardware at actual size

#10-¾" Phillips Pan

H

Head Screws

H

5.1

C

Center Support on
models over 48" wide

H

5.2

H

H

B

Two screws H
per hinge at
forward locations

H

5.3

H

5.4

Lid Stay

Attach to Worksurface Attach to Monitor Bay Lid

5.4 Attach the Lid Stay to the Monitor Bay Lid with two #10-¾" Phillips Pan Head Screws (H)
(see Adjustment Procedure, Step 11).

3 of 8 Line of Sight | [phone] | los.workriteergo.com

6 Attach Feet and Glides

CAUTION !

Product is spring loaded and may open with extreme force when screw is removed.

MISE EN GARDE !

Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.

¡

ATENCIÓN !

Éste producto està cargado con resortes y puede abrise con extrema fuerza cuando

se remueve éste tornillo.

6.1 Attach Le Foot (I) and Right Foot (J) from
the inside, bottom of Chassis using four
⅜-16×1¼" Flat Head Socket Cap Screws (K).
Note that the Le Foot will be on the right and
vice versa with the Chassis is upside down.

6.2 Screw in the four Glides (L) into the feet
approximately half way. You will level the
Workcenter once it has been flipped right side up.

Hardware at actual size

⅜-16 x 1" Flange Head Cap Screw

K

7 Flip Workcenter Over

J

6.1

K

6.2

L

6.1

I

K

K

K

Flip over the assembled Workcenter with at least
two people.

8 Remove Safety Screw

Remove the Safety Screw from the top of the Monitor Li with a #2 Phillips
screwdriver. Remove, but retain the screw in case you need to ship the
Workcenter without a monitor in the future.

CAUTION: The Monitor Li is spring loaded! Removing the Safety Screw
unlocks the mechanism allowing the Monitor Li to raise.

CAUTION!

Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.

MISE EN GARDE !

Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.

¡

ATENCION!

No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.

Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.

Product is spring loaded and may open with extreme force when screw is removed.

Éste producto està cargado con resortes y puede abrise con extrema fuerza cuando

CAUTION !

MISE EN GARDE !

¡

ATENCIÓN !

se remueve éste tornillo.

Top of Monitor Li

Under Workcenter

4 of 8 Line of Sight | [phone] | los.workriteergo.com

9 Raise Monitor Li

9.1 Li Lid fully open.

9.2 Press down on "PUSH HERE" label on top of the Manual Lis.

CAUTION! Spring loaded mechanism! Take care during

the first time Monitor Arm is activated. With no monitors in
the Monitor Mount, the mechanism is FULLY LOADED and
will spring up with maximum force.

9.1

Monitor Bay
Lid Handle

9.2

PUSH HERE TO RAISE OR

LOWER THE MONITOR

Caution: Spring loaded mechanism.

Exercise caution when cycling up or down!

Monitor Li

10

Complete Monitor Bay Lid Attachment

Finish attaching Monitor Bay Lid to both
Monitor Lid Hinges with two remaining
#10-¾" Phillips Head Screws (H) per hinge.

Note: Monitor Bay Lid will have
approximately .2" of clearance around the
cutout in the Worksurface when properly
installed. You may need to loosen the Hinge
Screws to adjust and re-tighten.

Hardware at actual size

#10-¾" Phillips Pan

H

Head Screws

11

Adjust Monitor Bay Lid-Stay Resistance

Use " or 4mm Allen wrench to turn
Adjustment Screw clock-wise until lid closes
soly and completely when released.

Previously installed
in Step 5.3

H

9.2

Adjustment Screw

" Allen wrench

If lid doesn't close completely, turn
Adjustment Screw counter-clockwise
slightly until lid closes soly and completely
when released.

5 of 8 Line of Sight | [phone] | los.workriteergo.com

12

Mount VESA Compatible Monitor to Monitor Li

Note: You will need to mount the monitors in order to determine
the correct installation height and counterbalance weight.
Remove the monitor from the factory mount if necessary, and
retain the screws that came with the monitor for Step 12.1.

12.1

or

Q

P

R

12.1 Attach VESA Plate (M) to the back of your VESA compatible
Monitor with Spacers (O), Screws (P, Q,R) and Washers (S) or use
the screws that came with your monitor. Always use the shortest
screws possible, so you do not damage your monitor.

12.2 Attach the VESA Bracket Monitor Assembly as high as possible
on the Monitor Li using two ¼"-20 × ½" Button Head Screws (N)
and the " Allen wrench.

Hardware at actual size

¼"-20 × ½" Button Head Screw

N

M4 × 10 mm Monitor Screws

P

M4 × 16 mm Monitor Screws

Q

M4 × 25 mm Monitor Screws

R

Attach VESA Bracket

Monitor Assembly

Important Note: It is strongly recommended to use

the mounting screws provided by the monitor manufacturer
if possible. If longer screws are required, use the shortest
screws possible to avoid damage to the monitor.

M

VESA compatible
monitor

" Allen wrench

N

12.2

13

Set Counterbalance Weight

Note: You will need to establish an equilibrium between
the weight of the monitor with Ballast Plates and the liing
force of the Monitor Li. Ballast Plates are best reached
from under the worksurface.

Remove the Wing Nut. With the
monitor installed, remove ballast
plates until the monitor fully
raises when the Monitor Li is
engaged.

Replace the Wing Nut to secure
in place.

Ballast Plate

6 of 8 Line of Sight | [phone] | los.workriteergo.com

Wing Nut

Under Worksurface

14

Install Power Distribution Options for Your Configuration

With the Workcenter built, you will now need to add your power options for your specific configuration. Follow
the instructions that came with the Power System Options to complete your configuration.

If you did not purchase the Power Track or Power Bar, skip to Step 15.

15

Install Optional Accessories for Your Configuration

With the monitors and power components installed, you will now need to add your optional accessories
like Worksurface Grommets, Remote Controls and CPU Holders. Follow the instructions with the Optional
Accessories to complete this step.

16

Install Technology for Your Configuration

With all Line of Sight components installed, you will now need to install all the technology components to
complete your system. Install all computers, peripherals like keyboards and mice, and network cabling to
complete your installation according to the manufacturers specifications and your specific application.

17

Manage Cabling

With monitors and technology installed, you'll want to
start considering all the cabling requirements.

T

U

Note: It is critical that no wires interfere with the travel
of the Monitor Li. Use Cable Clips (T) for single wires
(mouse & keyboard) and Cable Ties (U) for multiple wires
to fasten all cabling securely out of the way of all moving
Monitor Li components.

Use the Wire Loom (V) to
manage all user cables
routing from the keyboard
tray to the CPU. This may
include keyboard, mouse,
monitor and data cables.

18

Remove Protective Tape & Replace Front and Rear Panels

18.1 Remove the protective tape on the Panels and Chassis

18.2 Reattach your front and rear panels. You now have a

complete Workcenter. Finish building all Workcenters
before proceeding to final room assembly.

To CPU

18.1

Remove

Keyboard tray
cable access

V

18.2

Monitor Li

Remove

Front & Rear

Panels

7 of 8 Line of Sight | [phone] | los.workriteergo.com

Chassis

19

Assemble Final Room Configuration

With all individual Workcenter Built and electrical installed, arrange Workcenters according
to your final room configuration. You will need at least two people to move a Workcenter.

Adjust the Glides (L) on the bottom of the Feet to assure each Workcenter is level and stable in its final location.

Note: It is critical that you follow all warnings and cautions when you get to final assembly. Consult the
instructions that came with your electrical components and follow all cautions and warnings carefully!
Configurations with shared power must conform to code and include use of Ganging Brackets for Side to Side
configurations or Back to Back Filler Plates for Back to Back configurations.

Final assembly will include testing of electrical components and functioning of all Monitor Lis.

✓ Cleaning Instructions

Laminate Worksurfaces:

For everyday cleaning, wipe the surface with a damp cloth or sponge. Use a spray cleaning agent sparingly
if necessary (suggested spray cleaning agents are indicated below). Do not pour water directly onto the
worksurface. Wipe completely dry with a so rag using a straight line motion.

• Worksurfaces may need occasional dusting. To keep the surface in ideal condition, use a non-oily furniture
spray.

• Diicult stains such as coee can be removed using a mild cleaning detergent and a so bristled (non-metallic)
brush. Do not scrub surfaces with too much force, otherwise the surface could lose its finish.

• Stubborn stains that resist any of the above cleaning methods may require the use of undiluted household
bleach. Apply a very small amount of bleach (approximately ¼-capful) to the stain and let stand no longer than
two minutes. Rinse thoroughly with warm water and wipe dry. WARNING: Prolonged exposure of the laminate
surface with bleach will cause discoloration.

• Ensure to always rinse laminate surfaces aer cleaning. Even a small amount of cleaning residue can result in
permanent discolorations.

• Recommended Laminate Worksurface cleaning agents:

· Non-abrasive spray cleaning agents: Dawn, Fantastik, Windex, Lysol

· Furniture spray: Pledge

· Stain removers: Lestoil, Clorox

Painted steel parts:

• Clean surfaces regularly with damp cloth

• If necessary, use a spray cleaning agent (e.g. Fantastik) sparingly. Wipe completely dry with a so rag using a
straight line motion.

• Lightly brush both vertical and horizontal surfaces to prevent dust build-up

Polished chrome feet:

• The feet can be polished when they become dull with Aluminum polish (e.g. Flitz or Mothers Mag Polish) with
special attention to keep polish from painted surfaces. Follow manufacturers instructions for best results.

8 of 8 Line of Sight | [phone] | los.workriteergo.com

#1500380 Rev B