LIGHTING CONTROL MIXER
OPERATING INSTRUCTIONS
STAGE 4824 DMX
STAGE 2412 DMX
P
R
O
R
1
ENGLISH
The STAGE 4824 is a lighting control mixer where 4.600 steps and 96 programmes
can be recorder, suitable for theatres, auditoriums and halls where a lighting professional
control is necessary. Its high back-up allows to keep several stage configurations and
sequences for different events withourt the need to record them each the process is
repeated.
It is also possible to acced to its memory to change parameters and to personalize
each montage.
Memoriza the last position in case of mains cut. Edition of several programmes
simultaneously, able to edit scenes at the same time, chases and sequences of an
independent and simultaneous mode, getting a high quantities of effects from a few
base memories.
Put an stages by audio/crossfader/speedfader...according to act need.
Standar MIDI port (IN,OUT,THRU). Switch TAP Sync to synchronize chase steps and
scenes with programmed sequences. Time control by fader from 0 seconds to 10
minutes..
Display in % or 0-255, to get an exact level of regulation.
Connector DMX OUT XLR-3 pin with configurable polarity.
Out to release smoke machine.
P
R
O
R
Thanks for your reliability on us having acquired a product WORK.
We hope it provides you a long and reliable service.
ENGLISH
2
RECORD
16 86
MODE
SELECT
CHNS SCENES
A DOUBLE
PRESET B
1 - 48 SINGLE PRESET
Begin Programming
Record Enable
1 . Press and hold down the Record button.
2 . While holding down the Record button, tap the Flash button 1,6,6 and 8 in
sequence.
3 . Release the Record button, the Record LED lights up, now you can begin
programming your chase patterns.
NOTE :
The first you turn on your unit, the default setting of the Record Code is Flash
buttons 1, 6, 6 and 8.
Security for Your Programs
To protect your programs from any editing by others, you may change the Record
Code.
1 . Enter current Record Code (Flash buttons 1, 6, 6 and 8).
2 . Press and hold down the Record and Edit buttons at a time.
3 . Wkile holding the Record and Edit buttons, tap the desired Flash button to
enter a new Record Code.
4 . Enter your new Record Code a second time, all channel LEDs and scene
LEDs will flash three times, now the Record Code is changed.
5 . Exit Record mode. Tap the Rec Exit buyyon while pressing and holding dow
the Record button, release the two buttons at a time, the Record mode is
disengaged.
Program Scenes
IMPORTANT
Always remember to exit Record mode when you won't continue your programming,
otherwise you may lose control of your unit.
NOTE :
The second time you enter new Record Code different from that of the first time, the LEDs will not flash, which
means you've failed to change Record Code.
When you've entered a new Record Code the first time, and you want to cancel the new Record Code, you may
press and hold down the Record and Exit buttons at a time to exit.
1 . Record Enable.
2 . Select the 1 - 48 Single mode by tapping the Mode Select
button.This will give you control of all 48 channels as you
program. Be sure that Master A & B are both set at maximum.
(Master A is at its maximum in the fully up posiition, while
Master B is at its maximum in the fully down position)
ENGLISH
3
0
2
4
6
8
10
0
2
4
6
8
10
0
2
4
6
8
10
0
2
4
6
8
10
1
2
RECORD
PAG E
1234
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLASH 25 - 48
RECORD
REC
EXIT
Program Scenes
Create a desired scene using Channel Sliders
1-48 At % or DMX 0, these slider should be
at 0 position, and at 100% or DMX 255, these
sliders should be at 10 position.
3 .
Once the scene is satisfactory, tap the Record
button to program the scene as a step into the
memory.
4 .
Repeat step 3 and step 4 until all desired steps
have been programmed into memory.
You may program up to 1000 steps into
memory.
5 .
Select a chase bank or scene master to store
your program. Tap the Page button to selected
a page (Page 1-4) to store your scenes.
6 .
1 . Record enable.
2 . Push Master A & B to maximum position and Fade slider to top.
3 . Tap the Mode Select button to select 1-48 Single mode.
4 . Push Channel slider 1 to the top position, its LED light at full intensity.
5 . Tap the Record button to program this step into memory.
6 . Repeat steps 4 and 5 until you've programmed Channel slider 1-32.
7 . Tap the Page button causing Page 1 LED lights.
8 . Tap the Flash button 25 whle holding down the Record button, all LEDs will flash
indicating you've programmed the chase into memory.
7 . Press a Flash button between 25-48 while
holding down the Record button. All LED will
flash indicating the scenes have been
programmed into memory.
8 .
You can continue programming or exit.
To exit Program mode, tap the Exit button
while holding down the Record button, the
Record LED should go out.
EXAMPLE : Program a 16 steps chase with channel 1 - 32 at full in sequence into Flash button 25 of Page 1
ENGLISH
4
PAG E
1234
EDIT
MODE
SELECT
CHNS SCENES
A DOUBLE
PRESET B
1 - 24 SINGLE PRESET
0
2
4
6
8
10
0
2
4
6
8
10
EDIT
FLASH 25 - 48
PAG E
1234
0
2
4
6
8
10
0
2
4
6
8
10
EDIT
FLASH 25 - 48
Edit Enable
Record enable.
1 .
Use the Page button to selected the page the
program you wish to edit is on.
2 .
4 .
Press and hold down the Edit button.
Tap the Mode Select button to select.
3 .
CHNS SCENES
Edit Programs
Erase a Program
Tap this button twice
While holding down the Edit button, tap the
Flash button that corresponds to the program
you wish to edit.
5 .
Release the Edit button, the relevant scene
LED should light indicating you are in the Edit
mode.
6 .
Record enable.1 .
2 .
Use the Page button to select the page the
program you wish to erase in on.
3 .
White holding down the Edit button, tap the
Flash button(25-48) twice.
4 .
Release the two buttons, all LEDs flash,
indicating the program is erased.
ENGLISH
5
RECORD
14 32
RECORD
REC
CLEAR
STEP
DELETE
RECORD
REC
EXIT
Erase All Programs
Clear a Scene or Scenes
Delete a Step or Steps
1 . Press and hold the Record button.
2 . Tap the Flash button 1, 4, 2 and 3 in sequence while holding the Record button.
All LEDs will flash, indicating all programs stored in memory have been erase.
1 . Record enable.
2 . Record a scene or scenes.
3 .
If you are not satisfied with the scene or scenes, you may tap the
Rec Clear button while pressing and holding the Record button,
all LEDs will flash, indicating the scenes have bee cleared.
1 . Enter the Edit mode.
2 . Tap the Step button to scroll to the step you wish
to delete.
3 .
Tap the Delete button when you reach to the step you
wish to delete, all LEDs will flash briefly indicating the
deletion of the step.
4 . Continue steps 2 and 3 until all the unwanted step have been deleted.
5 .
Tap the Rec Exit button while pressing and holding down the Record
button, the Scene LED goes out, indicating the exit of Edit mode.
ENGLISH
6
Insert a Step or Steps
STEP
INSERT
MODE
SELECT
RECORD
Modify a Step or Steps
UP
STEP
0
2
4
6
8
10
0
2
4
6
8
10
UP
1 . Record a scene or scenes you wish insert.
2 . Be sure you're in CHNS SCENE and
Enter the Edit mode.
3 .
Tap the Step button to scroll to the step which
you wish to insert before. You may read the step
from the Segment Display.
4 .
Tap the insert button to insert the step you've
created before, all LEDs will flash, indicating
the step is inserted.
Exit Edit mode.
5 .
1 .
Enter Edit mode.
2 .
Tap the Step button to scroll to the step you wish to modify.
3 .
Press and hold the Up button if you want to
raise the intensity.
If you want to lower the intensity, press and
hold down the Down button.
4 . While holding down the Up or Down button, tap the Flash
button correponding to the DMX channel of the scene you
wish to modify until you reach the desired intensity value
read from the Segment Display. Then you may tap the Flash
button until you are satisfed with the new scene.
5 .
Repeat steps 2,3 and 4 until all the steps have been modified.
6 .
Exit Edit mode.
ENGLISH
7
Running Chase Programs
PAGE
1234
MODE
SELECT
CHNS SCENES
A DOUBLE
PRESET B
1 - 24 SINGLE PRESET
0
2
4
6
8
10
0
2
4
6
8
10
MASTER
MIN
MAX
MAX
MIN
A
B
Running a Program To Audio
AUDIO
0
2
4
6
8
10
0
2
4
6
8
10
AUDIO LEVEL
Running a Program With the Speed Slider
SPEED
.1 SEG
.2 S
.5 S
1 S
2 S
5 S
10 S
30 S
1 MIN
2 MIN
5 MIN
MINS
SHOW
MODE
.1 SEG
MINS
SHOW
MODE
10 MIN
1 MIN
2 MIN
5 MIN
20 S
10 S
5 S
2 S
1 S
.5 S
1 . Tap the Mode Select button select
mode indicated
by the red LED.
CHNS SCENES
2 . Tap the Page button to select the correct
page the program you wish to run is located.
3 .
Push Master Slider B to its maximum position
(fully down).
4 .
Move the desired Channel slider (25 - 48) (* 13 - 24) to its
maximum position to trigger the program, and the program
will fade in depending upon current fade time.
You may press and hold down the relevant Flash button
(25 - 48) (* 13 - 24) to trigger the program.
5 .
Move the Channel slider to adjust output of the current
program
1 .
Use built-in microphone or plug the audio soude
into the RCA Audio jack.
2 .
Select your program as described above.
3 .
Tap the Audio button until its LED lights, indicating
Audio mode is active.
4 .
Use the Audio Level slider to adjust the music
sensitivity
5 .
To reurn to normal mode, tap the Audio button a
second time causing its LED goes out, the Audio
mode is disengaged.
1 .
Be sure the Audio mode is disengaged, thast is, the
Audio LED goes out.
2 .
Select your program as described above.
3 .
Move the Speed slider to the SHOW MODE position
( the bottom), then tap the Flash button (25 - 48)
(*13 - 24) while pressing and holding down the Rec
Speed button, the corresponding program will not run
with the Standard beat any longer.
4 .
Now you may the Speed Slider to select your desired
speed
The step 3 is not necessary if the selected program is
not recorded with Standard Beat.
NOTE:
AUDIO
0
2
4
6
8
10
0
2
4
6
8
10
REC SPEED
FLAHS 25 - 48
(*FLAHS 13 - 24)
ENGLISH
8
Running a Program WitH the Standard Beat
PARK
SINGLE CHASE
MIX CHASE
RECORD
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLAHS 5 ó 10
Setting MIDI IN
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLAHS 1
0
2
4
6
8
10
0
2
4
6
8
10
FLAHS 1 - 16
SPEED
.1 SEG
.2 S
.5 S
1 S
2 S
5 S
10 S
30 S
1 MIN
2 MIN
5 MIN
MINS
SHOW
MODE
.1 SEG
MINS
SHOW
MODE
10 MIN
1 MIN
2 MIN
5 MIN
20 S
10 S
5 S
2 S
1 S
.5 S
Be sure the Audio is disengaged. Tap the Mode
Select button to select
mode.
CHNS SCENES
1 .
Tap the Park button to select Mix Chase mode,
the LED lights indicating this selection.
2 .
Select your program as described above.
3 .
Move the Speed slider until the Segment Display
reads your desired value.
4 .
5 . While pressing and holding down the Rec Speed button,
tap the Flas button (25 - 48) (*13 - 24) that stores the program.
6 . The program will then run with the set time or beat when
engaged.
7 .
Repeat steps 4 and 5 to set a new beat time.
Change the Speed Mode between 5 Minutes and 10 Minutes
0
2
4
6
8
10
0
2
4
6
8
10
REC SPEED
FLAHS 25 - 48
(*FLAHS 13 - 24)
1 .
Press and hold the Record button.
2 .
Tap the Flash button 5 or 10 three times while
holding down the Record button.
3 .
The 5 MIN or 10 MIN should light up indicating
the Speed slider is set to run in the 5 or 10
minute mode.
Tap this button
three times
Tap this button
three times
1 .
Tap the Flash button 1 three times while
holding down the Record button, the
Segment Display reads "CHI" indicating
MIDI IN channel setup is available.
2 . Tap the Flash button numbered from 1-16
to assing MIDI IN channel 1-16, the relevant
channel LED lights indicating MIDI IN
channel is set
ENGLISH
9
Setting MIDI OUT
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLAHS 2
0
2
4
6
8
10
0
2
4
6
8
10
FLAHS 1 - 16
Exit MIDI Setting
RECIBIR ARCHIVOS MIDI
RECORD
REC
EXIT
Sending MIDI File Dump
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLAHS 3
0
2
4
6
8
10
0
2
4
6
8
10
RECORD
FLAHS 4
Implementation
Tap this button
three times
Tap the Flash button 2 three times while
holding down the Record button, the
Segment Display reads "CHO" indicating
MIDI OUT channel setup is available.
1 .
Tap the Flash button numbered from 1-16
to assing MIDI OUT channel 1-16, the
relevant channel LED lights indicating MIDI
OUT channel is set.
2 .
Press and down the Record
button. While holding down
the Record button tap the
Rec Exit button to exit MIDI
setting.
Tap this button
three times
Tap the Flash button 3 three
times while holding down
the Record button, the
Segment Display reads "IN"
indicating the controller is
ready to receive MIDI file
dump.
Tap this button
three times
Tap the Flash button 4 three times
while holding down the Record
button, the Segment Display reads
"OUT" indicating the controller is
ready to send a file.
During file dump, all other operations will not function,
Functions will automatically return when the file dump is
completed.
File dump will be interrpted and stop if occur or power
failure.
NOTE:
During receiving and sending MIDI data, all MIDI scenes and channels being run will automatically paused
if there is no response within 10 minutes.
During receiving and sending file dump, the controller will automatically search for or send Device ID
of 55H(85), a file named DC2448 with an extension of "BIN(SPACE)".
File dump allows this controller to send its MIDI data next unit or other.
ENGLISH
10
Implementation
Close Loop Mode
Open Loop Mode
Brief of Main Functions
NOTE
Decimal
22 - 69
70 - 117
118
119
120
121
122
123
124
125
126
NUMBER
Hex
(16H-45H)
(46H-75H)
(76H)
(77H)
(78H)
(79H)
(7AH)
(7BH)
(7CH)
(7DH)
(7EH)
VELOCITY
Program Master
channel light
FUNCTION
Turn On or Off program 1-48
activate Channel 1-48
FULL-ON
DARK
HOLD
Turn On or Off AUDIO
CHNS < > SCENES
DOUBLE PRESET Mode
SINGLE PRESET Mode
Step
BLACK OUT
NOTE Nº
22 - 69
70 - 93
94
95
96
97
98
99
100
101
102
STAGE 4824 STAGE 2412
There are two types of file dump mode described as below :
Program Master
channel light
VELOCITY
FUNCTION
Turn On or Off program 1-48
activate Channel 1-24
FULL-ON
DARK
HOLD
Turn On or Off AUDIO
CHNS < > SCENES
DOUBLE PRESET Mode
SINGLE PRESET Mode
Step
BLACK OUT
Reverse the direction of all the scenes. Press the ALL REV Button, all the scenes should change their directions.
Reverse the chasing direction of all the programs with speed control. Press the Chase Rev Button.
Reverse the chasing direction of all the programs with standar beat. Press the Beat Rev Button.
Reverse chasing direction of any program. Press and hold down the Rec One Button, then press down the Flash Button correspondin to
your desired program and release together.
The amount of time it will take for the dimmer to go from zero output to maximum output, and vice verse.
Fade time is adjusted through the Fade Time Slider, which varies from instant to 10 minutes.
The Tap Sync button is used to set and synchronize the chase rate (the rate at which all scenes will sequence) by taping the button several
times. The chase rate will synchronize to the time of the last two taps. The LED above the Step Button will flash at the new chase rate. The
chase rate may be set anytime whether or not a program is running.
Tap Sync will override any previous setting of the speed slider control until the slider is moved again.
Use of Tap Sync in setting a standard beat is the same with speed control slider.
RECEIVER
CONTROLLER
MIDI IN
MIDI OUT
MIDI IN
MIDI OUT
RECEIVER
MIDI IN
MIDI OUT
MIDI IN
MIDI OUT
CONTROLLER
Master Slider control provides proportional level control over all channels and scenes with the exception of the Flash Buttons. For example:
Whenever the Master slider control is at minimum all stage outputs will be at zero excepte for any resulting from a Flash Button or FULL
ON Button.
If the Master is at 50%, all outputs will be at only 50% of the setting of current channel or scenes except for any resulting from a Flash Button
or FULL ON Button.
If the Master is at full all outputs will follow the unit setting.
Master A always controls outputs of channels. Master B controls the program or a scene except in Double Preset Mode.
Master Slider
Tap Sync Button:
Fade Time
Reverse the direction of the scene
ENGLISH
11
Single Mode
Modo Duble Preset
Mix Mode
All programs will run in sequential order starting in the order of program number.
The Segment Display will read the running program number.
All programs will be controlled by the same Speed Slider.
Press the MODE SELECT BUTTON and select "CHNS < > SCENES".
Press the PARK BUTTON to select MIX CHASE MODE. A red LED will indicate this selection.
Will run all programs synchronously.
All programs can be controlled by the same SLIDER SPEED, or each programs speed may be controlled individually. (See Speed Setting).
Press the MODE SELECT BUTTON and select "CHNS <> SCENES".
Press the PARK BUTTON to select MIX CHASE MODE. A yellow LED will indicate this selection.
The 3-Digit Segment Display is used to display intensity percentage or absolute DMX value.
To change between percentage and absolute value. Press and hold the Shift Button. While holding down the Shift button press the % or
0-255 Button to switch between percentage and absolute values.
If the Segment Display reads, for example, "076", it means a percentage value 76%. If the Segment Display reads "076", it means the
DMX value 76.
Blind function takes channels temporally out from a chase, when the chase is running, and gives you manual control over the channel.
Press and hold the Blind Button and tap the relative Flash Button you want temporarily take out of the chase.
To return to normal chase again press and hold the Home Button and push the Flash Button you want to return normal chase.
In CHNS < > SCENES Mode, press down the button you can change the chasing mode of programs between Single Mode and Mix Mode.
In Double Preset Mode, pressing down this button is equal to pushing Master Slider B to the top.
In Single Preset Mode, this button could temporally record current output, with Master Slider B to adjust.
The ADD/KILL Button changes the mode of the flash buttons. Normally the flash buttons are in Add mode, whereas pressing any flash
button will not kill other scenes, allowing multiple scenes to be on at a time.
The Kill mode is activated by pressing the Add/Kill button and illuminating the LED above it. Pressing any flash button will kill other active
SCENE or Program.
In Kill Mode, the killed program does not stop running but can not output.
Press Mode Select Button to enter A double Preset Mode.
In this mode, Channel Slider 1 - 24 (* 1 - 12) and channel sliders 25 - 48 (* 13 - 24) both control Channel 1 - 24 (* 1 - 12).
Master A controls channel Slider 1 - 24 (* 1 - 12) while Master B controls Channels Sliders 25 - 48 (* 13 - 24).
In this Mode, no scene could be recorded.
Dimmer Display
Blind and Home
Park
Add - Kill
Example
Enter the Double Preset Mode.
Push Channel Slider 1 to 6 to the and move Channel Sliders 19 to 24 to the maximum.
Move Master A and B to the same level and push them to the same direction, you will get a scene.
Technical Specifications
Power Input
DMX Output
MIDI Signal
Audio Input
Fuse (internal)
Weight
DC 12 - 20 V. 500 mA. min.
3 pin female XLR
5 pin standard Interface
100 mV - 1 Vpp.
Fo. 5A 250V 5x20 mm
7,2 K. (* 4,6)
To retain your programs from loss, this unit must be powered not lees than two hour every month.
The Segment Display shows "LOP" if the voltage is too low.
Attention!
ENGLISH
12
STAGE 4824 DMX
1
2
3
4
5
6
7
16
17
18
19
20
21
22
23
242526
27
28
29
30
31
33
32
8
9
10
11
12
13
14
15
34
264 mm.
711 mm.
Preset A LEDs
Cannel Sliders 1 - 24
Flash Buttons 1 - 24
Preset B LEDs
SCENE LEDs
Channel Sliders 25 - 48
Flash Buttons 25 - 48
Dark Button
Down/Beat Rev
Mode Select/Rec Speed
Up/Chase Rev
Page Button
Delete/Rev One
Segment Display
Insert / % ó 0-255
Edit / All Rev
Add o Kill / Rec exit
Record / Shift
Master A Button
Park Button
FRONT
Show the current intensity of the relevant channel number from 1 to 24.
These 24 sliders are used to control and / or program the intensities of
channels 1 - 24.
These 24 buttons are used to brind an individual channel, to full intensity.
Show the current intensity of the relevant channel numbered from 25-48.
Light when relevant scenes are active.
These 24 sliders are used to control and / or program the intensities of
channels 25 - 48.
The 24 buttons are used to bring an individual channel, to full intensity.
They also are used for programming.
This button is used to momentarily black out overall output.
DOWN functions to modify a scene in edit mode; BEAT REV is used to
reverse the chasing direction of a program with regular beat.
Each tap will activate the operating mode in the order: CHNS / SCENES,
Double Preset.
Rec Speed: Set the speed of any of the programs chasing in Mix mode.
Up is used to modify a scene in Edit mode.
Chase Rev is to reverse the chasing direction of scene under Speed
Slider control.
Tap to select pages of secenes from Page 1 - 4.
Delete any step of a scene in Edit mode.
Chase Rev is to reverse the chasing direction of any program.
Show the current activity or programming state.
Insert is to add one step osteps into a scene.
% or 0 - 255 is used to change display value cycle between % and 0-255
17
18
19
20
Edit is used to activate Edit mode.
All Rev is to reverse the chasing direction of all programs.
In Add mode, multiple scenes or Flash button will kill any other scenes
or programs.
In Kill mode, pressing any Flash button will kill any other scenes or
programs.
Rec Exit is used to exit from Program or Edit mode.
Record is used to activate Record mode or program a step.
Shift functions only used with other buttons.
Brings channel 1 - 12 to full of current setting.
Used to select Single / Mix Chase, bring Channel 13 - 24 to full current
setting, or momentarily program a scene into Master B slinder, depending
on the current mode.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FRONT
Blind Button
Home Button
Tap Sync Button
Full On Button
Black Out Button
Fade Time Slider
Speed Slider
Audio Level Slider
Fog Machine Button
Hold Button
Step Button
Audio Button
Master Slider A
Master Slider B
21
22
23
24
25
26
27
28
29
30
31
32
33
34
This button is used to maintain curret scene.
This button is used to go to next step when the Speed Slider is
pushed to the button or in Edit mode.
Activates audio sync of chase and audio intensity effects.
This slider controls overall output of all channels.
This slider controls the chase of all programs.
This function takes the channel out of the chase of a program in
CHNS / SCENE mode.
This button is used to deactivate the Blind.
Repeatedly tapping this button establish the chase speed.
This function bring overall output to full intensity.
This button is used to kill all output with exception for that resulting
from Flash and Full On.
Used to adjust the Fade Time.
Used to adjust the chase speed.
The slider controls the sensitivity of the Audio input.
ENGLISH
13
STAGE 4824 DMX
36
35
42
41
40
3938
37
85 mm
482 mm.
1
2
3
4
5
6
7
16
17
18
19
20
21
22
23
242526
27
28
29
30
31
33
32
8
9
10
11
12
13
14
15
34
264 mm.
REAR
FRONT
FRONT
STAGE 2412 DMX
Preset A LEDs
Cannel Sliders 1 - 12
Flash Buttons 1 - 12
Preset B LEDs
SCENE LEDs
Channel Sliders 13 - 24
Flash Buttons 13 - 24
Dark Button
Down/Beat Rev
Show the current intensity of the relevant channel number from 1 to 12.
These 12 sliders are used to control and / or program the intensities of
channels 1 - 12.
These 12 buttons are used to brind an individual channel, to full intensity.
Show the current intensity of the relevant channel numbered from 13-24.
Light when relevant scenes are active.
These 12 sliders are used to control and / or program the intensities of
channels 13 - 24.
The 24 buttons are used to bring an individual channel, to full intensity.
They also are used for programming.
This button is used to momentarily black out overall output.
DOWN functions to modify a scene in edit mode; BEAT REV is used to
reverse the chasing direction of a program with regular beat.
1
2
3
4
5
6
7
8
9
Mode Select/Rec Speed
Up/Chase Rev
Page Button
Delete/Rev One
Segment Display
Insert / % ó 0-255
Edit / All Rev
Add o Kill / Rec exit
Record / Shift
Master A Button
Park Button
Each tap will activate the operating mode in the order: CHNS / SCENES,
Double Preset.
Rec Speed: Set the speed of any of the programs chasing in Mix mode.
Up is used to modify a scene in Edit mode.
Chase Rev is to reverse the chasing direction of scene under Speed
Slider control.
Tap to select pages of secenes from Page 1 - 4.
Delete any step of a scene in Edit mode.
Chase Rev is to reverse the chasing direction of any program.
Show the current activity or programming state.
Insert is to add one step osteps into a scene.
% or 0 - 255 is used to change display value cycle between % and 0-255
17
18
19
20
Edit is used to activate Edit mode.
All Rev is to reverse the chasing direction of all programs.
In Add mode, multiple scenes or Flash button will kill any other scenes
or programs.
In Kill mode, pressing any Flash button will kill any other scenes or
programs.
Rec Exit is used to exit from Program or Edit mode.
Record is used to activate Record mode or program a step.
Shift functions only used with other buttons.
Brings channel 1 - 12 to full of current setting.
Used to select Single / Mix Chase, bring Channel 13 - 24 to full current
setting, or momentarily program a scene into Master B slinder, depending
on the current mode.
10
11
12
13
14
15
16
Power Switch
DC Input
MIDI Thru / Out / In
DMX Out
DMX Polarity Select
Audio Input
Remote Input
Fog Machine Connector
REAR
DC 12-20V. 500 mA. mín.
35
36
37
38
40
41
42
This switch turming on or off of the power.
MIDI ports for connection to a sequencer or MIDI device.
This connector sends your DMX value to the DMX fixture or DMX
pack.
Used to select DMX polarity.
Black Out and Full On may be controlled by remote control using
a standard 1 / 4" stereo jack.
This RCA accepts a line level audio input signal ranged from 100mV
to 1Vpp.
39
ENGLISH
14
Blind Button
Home Button
Tap Sync Button
Full On Button
Black Out Button
Fade Time Slider
Speed Slider
Audio Level Slider
Fog Machine Button
Hold Button
Step Button
Audio Button
Master Slider A
Master Slider B
21
22
23
24
25
26
27
28
29
30
31
32
33
34
This button is used to maintain curret scene.
This button is used to go to next step when the Speed Slider is
pushed to the button or in Edit mode.
Activates audio sync of chase and audio intensity effects.
This slider controls overall output of all channels.
This slider controls the chase of all programs.
This function takes the channel out of the chase of a program in
CHNS / SCENE mode.
This button is used to deactivate the Blind.
Repeatedly tapping this button establish the chase speed.
This function bring overall output to full intensity.
This button is used to kill all output with exception for that resulting
from Flash and Full On.
Used to adjust the Fade Time.
Used to adjust the chase speed.
The slider controls the sensitivity of the Audio input.
36
35
42
41
40
3938
37
85 mm
REAR
REAR
Power Switch
DC Input
MIDI Thru / Out / In
DMX Out
DMX Polarity Select
Audio Input
Remote Input
Fog Machine Connector
DC 12-20V. 500 mA. mín.
35
36
37
38
40
41
42
This switch turming on or off of the power.
MIDI ports for connection to a sequencer or MIDI device.
This connector sends your DMX value to the DMX fixture or DMX
pack.
Used to select DMX polarity.
Black Out and Full On may be controlled by remote control using
a standard 1 / 4" stereo jack.
This RCA accepts a line level audio input signal ranged from 100mV
to 1Vpp.
39
Finally, we want to remember you that:
- Keep the set far from the humidity and avoid that any kind of liquids fo into it. If
this occurs being the mixer switches on, switch it off immediately from the mains.
- Place the mixer away from excessive heat and from direct sunlight.
- Avoid to accumulate dust, above all in the connectors and in the cooling grilles.
- Prevent that metallics objects enter into the mixer.
- If the mixer or the protecting fuses burn out, replace by ones with the same value.
Under no cirumstance, try repair a fuse.
- If you set up the mixer in a rack, be sure that it disposes of an air renovation grille.
EQUIPSON S.A.
POLIG. IND. LA ERMITA. NAVE K 1
TELF. 34 961 795 915
FAX 34 961 795 886
46439 EL ROMANI - SOLLANA
( VALENCIA - ESPAÑA )
E-MAIL: equipson@equipson.com
WEB: http://www.equipson.com
Loading...