isgl h
En
SCAN 812 DMX
User Manual
ENGLISH
R
P
R
O
Thanks for your reliability on us having acquired a product WORK.
We hope it provides you a long and reliable service.
SCAN 812 DMX. Console for scanners control with protocol of comunication
USITT DMX 512.
Possibility to control until 12 scanners of 16 channels each one.
Transfer and performance time control in order to be able to make flexible the
programmes edition.
Simultaneous edition of several chases beig able to generate a great quality
off effects.
TAP-SYNC button to be able to generate times asincronous according to the
program needs.
Internal microphone.
XLR-3 pins connector
MIDI control.
It memorizes the last state of edition in case of mains cut, returning to the
execution state to return of the same.
1
Program Enable
Programming Scenes
SCANNER BUTTONS 1-12
MIDI / REC
When the power is turned on, this unit enters Manual mode
automatically.
Press the Program button for three seconds to activate Program
mode, a fast blinking light in the Segment Display next to PROG.
Indicates its selection.
1 .
Enter Program mode.
Press the Scanner button to turn on its fader control, which
2 .
is indicated by lit LED.
You may select several scanners at a time by tapping of these
Scanner buttons, so you can assign several fixtures at a time
with this unit.
Create a desired scene using the faders. The DMX value is
3 .
0 when the fader is fully down(bottom) and 255 when it is fully
up(top).
If necerssary, you may tap the Page Select button to control
4 .
the second set of 8 DMX channels.
ENGLISH
SCENE BUTTONS 1-8
PROGRAM
Scene Editing
5 .
Once the scene is satisfactory, tap the MIDI/Rec button to
program this scene into memory.
Tap the Bank Up/Down button to select the bank you want to
6 .
store your scene into. There are total 30 bank you can select,
you may store up to 8 scenes into each bank.
Tap the Scene button to store your scene, all LEDs and the
7 .
Segment Display will flash three times briefly indicating this
operation, then the Segment Display will show the bank and
the scene.
Repeat steps 3-7 until all desired scenes have been
8 .
programmed into memory. Tap the Scanner button again to
turn off its fader control.
To assing another scanner (fixture), you may tap the
corresponding Scanner button to turn on its fader control, the
you may begin your programming again.
9 .
If you wish not continue your programming, press and hold
down the Program button for three seconds to exit Program
mode, the blinking light in the Segment Display goes out
indicating this selection.
BANK
SCANNER BUTTONS 1 - 12
BANK
SCENE BUTTONS 1-8
1 . Program enable.
Tap the Bank Up/Down button to select the bank that contains
2 .
the scene you wish to edit.
Select the sceneyou want to edit tapping its Scene button.
3 .
4 .
Use the Faders to make your desired adjustments.
2
Scene Editing
ENGLISH
MIDI / REC
Scanner Copy
SCANNER
5 .
Once you've made your changes, tap the MIDI/Rec button
Tap the Scene button that corresponds to the scene you're
6 .
editing. This will overwrite the exited scene.
NOTE:
Be sure to select the same scene in steps 3 and 6, otherwise
you may accidentally record over an exited scene.
This function allows you to copy the setting of one scanner
to another.
1 .
Press and hold down the Scanner button you want to copy.
2 . While holding the Scanner button, tap the Scanner button
you want to copy to.
SCENE
SCANNER
Scene Copy
BANK
BANK
SCENE
1 . Program enable.
2 . Tap the Bank Up/Down button to select the bank that contains
the scene you wish to copy.
3 . Select the scene you want to copy by tapping its Scene button.
4 . Tap the Bank Up/Down button to select the bank you wish to
copy the scene to.
5 . Tap the MIDI/Rec button.
6 . Tap the Scene button you wish copy the scene to.
SCENE
MIDI / REC
Delete a Scene
SCENE
1 . Tap the desired Scene button to select the scene you
wish to delete.
2 . Press and hold down the Auto/Del button.
While holding down the Auto/Del button, tap the Scene
button that stores the scene you wish to delete.
When a programmed scene is deleted, all DMX channel
in this scene is set to 0.
AUTO/DEL
SCENE
3
Delete all Scenes
PROGRAM
BANK
Bank Copy
BANK
This function will reset all DMX channel to 0 output.
1 . With the power off, press and hold down the Program and
Bank Down buttons at a time.
2 . Apply power again, all scenes should be cleared.
1 . Program enable.
2 . Tap the Bank Up/Down button to select the bank you wish
to copy.
3 . Tap the MIDI/Rec button.
4 . Tap the Bank Up/Doown button to select the bank you wish
copy to.
5 . Tap the Music/Bank Copy button, all LEDs and the Segment
Display will flash three times briefly indicating the function
has been completed.
ENGLISH
MIDI / REC
MUSIC/BANK COPY
6 . Press the Program button for three seconds to exit
Programming mode.
Programming Chase
You must program scenes before you can program chases, this
function allows you to store up to 240 scenes into one chase.
CHASE BUTTONS 1-6
1 . Program enable.
2 . Tap the Chase button to select the chase to program. Each
time you can select a chase only.
3 . Select a desired scene from the bank that has stored
scenes.(described in Programming Scenes).
MIDI / REC
4 . Tap the MIDI/Rec button.
5 . Repeat steps 3-4 until you've reached your desired effect.
You may record up to 240 scenes into a chase.
Program a bank of scenes into a Chase
BANK
MUSIC/BANK COPY
1 . Program enable.
2 . Select the chase using Chase buttons 1-6.
3 . Use Bank Up/Down button to select the bank that contains
the scenes you wish to copy.
4 . Tap the Music/Bank Copy button.
5 . Tap the MIDI/Rec Copy button, all LEDs and the Segment
Display button causing a highlight next to STEP, the first digit
in the Segment Display shows the chase and the next three
digits show its step.
MIDI / Rec Copy
4
Add a Step
ENGLISH
TAP SYNC/DISPLAY
1 . Program enable.
2 . Select the chase you wish to add a step to.
3 . Tap the Tap Sync/Display button causing a highlight next to
STEP, the firt digit in the Segment Display shows the chase
and the next three digits shows its step.
4 . Tap the Bank Up/Down button to scroll to the step you wish
BANK
to add a step after.
MIDI / REC
5 . Tap the MIDI/Rec button, the Segment Display will read the step one higher than before.
For example, if you want to insert a step between step 3 and step 4, and you scroll to step
3, when you tap the MIDI/Rec button, the Segment Display will read step 4.
6 .
Tap the Tap Sync/Display button again, the Segment Display shows the current chase, scene and bank.
Create a desired scene and record it as a new step or select a programmed scene you wish to add into this chase.
Hints : You may tap the Tap Sync/Display button to change the display mode between and the bank.
Tap the MIDI/Rec button again, all LEDs and the Segment Display will flash three times briefly indicating the new step has
7 .
been inserted into this chase.
Delete a Step
1 . Program enable.
2 . Select the chase that contains the step you wish to delete.
TAP SYNC/DISPLAY
AUTO/DEL
Delete a Chase
CHASE Button 1-6
3 . Tap the Tap Sync/Display button causing the Segment Display
shows the steps.
4 . Tap the Bank Up/Down button to scroll to the step you wish
to delete.
5 . Tap the Auto/Del button to delete the step, all LEDs and the
Segment Display will flash three times briefly indicating that
the step has been deleted.
1 . Select the chase you wish to delete.
Press and hold down the Auto/Del button.
2 .
Tap the Chase button while holding down the Auto/Del
button, all LEDs and the Segment Display will flash three
times briefly indicating this chase has been deleted.
BANK
AUTO/DEL
CHASE
5
Delete all Chases
AUTO/DEL
BANK
Running Scenes
Manual Mode
SCENE
1 . With the power off, press and hold down the Auto/Del and Bank Down buttons same time.
2 .
Apply the power again.
1 . When the power is turned on, this unit enters Manual mode automatically.
2 . Make sure Auto trigger and Music trigger indicators in the Segment Display are both off.
3 . Use the bank Up/Down button to select the bank that contains the scenes you wish to run.
4 . Tap the Scene button to select the scene to run.
ENGLISH
Auto Mode
BANK
SPEED FADE TIME
Music Mode
This function allows you to run a bank of programmed scenes in a sequential loop.
1 . Tap the Auto/Del button to activate Auto mode.
AUTO/DEL
A highlight nex t AUTO TI¡RIGGER will indicate Auto mode.
2 . Use the Bank Up/Down button to select a bank of scenes to run
3 . After selecting the bank of scenes you wish to run, you can use the Speed slider(or Tap
Sync/Display button) and Fade Time slider to adjust the scenes to your desired effect.
Hints:
The Tap Sync button is used to set the speed by tapping the button
several times, the last two taps will define the speed with a
AUTO/DEL
maximum of 10 minutes. Tap Sync will override any previous
setting of the Speed slider unless the slider is moved again.
4 . Tap the Auto/Del button again to exit Auto mode.
MUSIC BANK COPY
1 . Tap the Music/Bank Copy button to activate Music mode.
A highlight next to MUSIC TRIGGER indicates Music Mode.
2 . Use the Bank Up/Down button to select the bank that holds
the scenes you wish to run. The scenes you've selected will
chase in a sequential order according to the music rhythms
detected by the built-in microphone
3 . Tap the Music/Bank Copy button again to exit Music mode.
BANK
6
Running Chases
ENGLISH
Manual Mode
BANK
Auto Mode
You must program scenes before you can run chases.
1 . When the power is turned on, this unit enter Manual mode automatically.
2 . Select your desired chase by tapping one of the six Chase buttons. A second tap of this button
will deactivate this function.
3 . Use the Speed slider (or Tap Sync button) and Fade Time slider to adjust the current scenes
to your desired effects.
4 . Use the Bank Up/Down button to scroll through the chase to run all banks of scenes.
AUTO/DEL
CHASE BUTTONS 1-6
Music Mode
MUSIC/BANK COPY
1 . Tap the Auto/Del button to activate Auto mode. A highlight nex to
AUTO TRIGGER will indicate Auto mode.
2 . Select yor desired chase by tapping one of the six Chase buttons.
A second tap of this button will desactivate this function.
3 . Use the Speed slider (or Tap Sync) and Fade Time slider to adjust
the chase to your desired effects.
You may select several chases at a time, the chases will run in
sequence that you select the chases.
1 . Tap the Music/Bank Copy button to activate Music mode. A
highlight in the Segment Display next to MUSIC TRIGGER will
indicate Music mode.
2 . Select your desired chase by tapping one of the six Chase
buttons, the chase will be triggered by the music rhythms.
You may select several chases at a time.
SPEED FADE TIME
CHASE BUTTONS 1-6
MIDI Operation
MIDI Channel Setting
1 . Press and hold down the MIDI/Rec button for three seconds,
the last two digits of the Segment Display will flash to indicate
MIDI channel setting is ready.
MIDI/REC
2 . Use the Bank Up/Down button to select the DMX channel 01-
16 to assign to MIDI channel.
3 . Press and hold down the MIDI/Rec button for three seconds
to store your setting and to deactivate MIDI setting.
If you wish to give up your setting, tap any other button (except
Bank Up/Down buttons) to exit MIDI mode.
7
BANK
Implementation
This unit receives Note On signals, which enables to run 15 bank (01-15) of scenes and 6 chases of scenes. In addition, blackout function can
be activated by MIDI signal.
BANK NOTE Nº FUNCTION
Bank 1 00 to 07 Turn on or off Scenes 1-8 of Bank 1
Bank 2 08 to 15
Bank 3 16 to 23
Bank 4 24 to 31
Bank 5 32 to 39
Bank 6 40 to 47
Bank 7 48 to 55
Bank 8 56 to 63
Bank 9 64 to 71
Bank 10 72 to 79
Bank 11 80 to 87
Bank 12 88 to 95
Bank 13 96 to 103
Bank 14 104 to 111
Bank 15 112 to 119
120
Chase 2
Chase 3
Chase 4
Chase 5
Chase 6
121
122
123
124
125
126 BLACKOUT
Turn on or off Scenes 1-8 of Bank 2
Turn on or off Scenes 1-8 of Bank 3
Turn on or off Scenes 1-8 of Bank 4
Turn on or off Scenes 1-8 of Bank 5
Turn on or off Scenes 1-8 of Bank 6
Turn on or off Scenes 1-8 of Bank 7
Turn on or off Scenes 1-8 of Bank 8
Turn on or off Scenes 1-8 of Bank 9
Turn on or off Scenes 1-8 of Bank 10
Turn on or off Scenes 1-8 of Bank 11
Turn on or off Scenes 1-8 of Bank 12
Turn on or off Scenes 1-8 of Bank 13
Turn on or off Scenes 1-8 of Bank 14
Turn on or off Scenes 1-8 of Bank 15
Turn on or off Chase 1Chase 1
Turn on or off Chase 2
Turn on or off Chase 3
Turn on or off Chase 4
Turn on or off Chase 5
Turn on or off Chase 6
ENGLISH
Technical Specifications
Power Input
DMX Output
MIDI Signal
Audio Input
Weight
Finally, we want to remember you that:
- Keep the set far from the humidity and avoid that any kind of liquids fo into it. If this occurs
being the mixer switches on, switch it off immediately from the mains.
- Place the mixer away from excessive heat and from direct sunlight.
- Avoid to accumulate dust, above all in the connectors and in the cooling grilles.
- Prevent that metallics objects enter into the mixer.
- If the mixer or the protecting fuses burn out, replace by ones with the same value. Under
no cirumstance, try repair a fuse.
DC 9 - 12 V. 5 00 mA. min.
3 pin female XLR
5 pin standard interface
By built-in microphone
2,5 Kg
- If you set up the mixer in a rack, be sure that it disposes of an air renovation grille.
8
USN CONNECTION ABLE
FROM 2006 VERSION
2
Scene Buttons
Press the scene buttons to load or stored your scenes. There are maximum of
240 programable scenes.
10
11
3
4
5
6
7
8
9
Segment Display
Bank Buttons(Up/Down)
Chase Buttons(1-6)
Program Button
MIDI/Rec Button
Auto/Del Button
Music/Bank Copy
Blackout Button
Tap Sync/Display
Shows the currnt activity or programming state.
Press the Up/Down buttons to select a bank 30 banks.
Used to select your programmed chase consisting a maximum of 240 scenes.
Used to activate Program mode.
Used to control MIDI operation or to record programs.
Used to activate Auto mode or to delete scenes and chases.
Used to activate Music mode or to create scenes and chase programs.
Used to disable channel output.
Used to create a standard beat or to change the values display between % and 255.
12
13
14
15
Fade Time Slider
Speed Slider
Page Select Button
Faders
TRASERA REAR
16
17
18
MIDI IN
USB Light Connector Allows a USB DJ work light to be plugged into it.
DMX Out
Used to adjust the Fade Time. Fade Time is the amount of time it takes for a fixture
(scaner) to move from one position to another, for the dimmer to fade in or fade out.
Used to adjust the speed at which the scenes will chase.
Used to select faders for the fixture between Page A (1-8) and Page B (9-16)
This faders are used to control intensity of channel 1-8 or channel 9-16 depending
upon the selected page.
Receives MIDI data.
This connector sends your DMX value to the DMX fixture or DMX pack.
19
DC Input
DC +9-12 V. 5 00 mA min.
10
Equipson, S.A.
www.equipson.es
support@equipson.es
Loading...