MySpot Installation Manual
Right hand tablet Left hand tablet
Assembly instructions for all catalog numbers beginning with:
MS.M.1.LT
MS.C.1.LT
MS.M.1.RT
MS.C.1.RT
(Single chair with a right hand or left hand tablet)
Tools required for assembly:
#2 Phillips screw driver
#3 Phillips screw driver
Slotted screw driver
3/16” hex wrench
6mm hex wrench
5/16” open end wrench
Hammer
Needle nose pliers
Power screw driver (optional)
8/9/2010 Page 1 of 30
Parts required to assemble (1) chair:
(1) – Internal back panel
(21-1/8”H x 24-1/2”W)
(2) – Internal end panels
(21-1/16”H x 22-1/2”W)
(1) – Outer back cover panel
(21-3/16”H x 24-1/2”W)
(2) – End left face cover panels
(21-3/16”H x 22-1/2”W)
8/9/2010 Page 2 of 30
Parts required to assemble (1) chair (continued):
(2) – End right face cover panels
(21-3/16”H x 22-1/2”W)
(1) – Left front leg
(2-1/4”SQ x 24-3/16”H)
(2) – Back legs
(2-1/4”SQ x 26-1/2”H)
(1) – Right front leg
(2-1/4”SQ x 24-3/16”H)
8/9/2010 Page 3 of 30
Parts required to assemble (1) chair (continued):
LH OR RH
(1) - Left hand or right hand tablet assembly
(1) – Seat support beam
(24-7/8”L)
8/9/2010 Page 4 of 30
(1) – Bottom panel
(23-5/8” x 24-3/8”)
Parts required to assemble (1) chair (continued):
(1) – Back cushion
(1) – Seat cushion
(2) – Arms
(6”W x 29”L)
(3) – Arm plates (4” x 4”)
(1) – Arm standoff (1-1/4”DIA x 2-1/4”H)
(1) – Z-bar (21-3/16”L)
8/9/2010 Page 5 of 30
Hardware required to assemble (1) chair (shown actual size):
(4) 1/4-20 x 3/4” pan head machine screws – zinc (part# 1001501)
(4) 5/16-18 x 1” flat head socket cap screws – black (part# 26797)
(2) 5/16-18 x 3” flat head socket cap screws – black (part# 1001771)
(1) 5/16-18 x 4” flat head socket cap screw – black (part# 26786)
(16) #12 x 3/4” flat head wood screws – zinc (part# 26791)
(10) #10 x 1-1/4” flat head wood screws – black (part# 1001591)
(4) #10 x 1-1/2” flat head wood screws – black (part# 1001592)
(6) #12 x 5/8” pan head wood screws – black (part# 4300-1738)
8/9/2010 Page 6 of 30
Hardware required to assemble (1) chair (shown actual size) (continued):
(20) #14 x 3/8” shoulder screws – zinc (part# 26794)
(18) Cam pins – nickel (part# 29989)
(18) Cams – zinc (part# 29988)
(10) Figure-8 fasteners – zinc (part# 1001663)
(3) 5/16-18 barrel nuts – zinc (part# 1001741)
8/9/2010 Page 7 of 30
8/9/2010 Page 8 of 30
1 (2) #10 x 1-1/4” (2) Figure-8
Screw (2) Figure-8’s into the predrilled holes in
the bottom edge of the internal back panel.
1 2
8/9/2010 Page 9 of 30
2 (4) 1/4-20 x 3/4"
Attach the Z-bar onto the inside of the internal back panel.
1 2
8/9/2010 Page 10 of 30
3 (12) Cam pins
Screw (6) cam pins into each back leg.
1 2
8/9/2010 Page 11 of 30
4 (2) 5/16-18 x 3” (2) Barrel nuts
Attach an arm plate to each back leg as shown
to make a right and a left back leg assembly.
1 2
LEFT
RIGHT
8/9/2010 Page 12 of 30
5 (6) Cams
Fasten the back legs to the internal back panel.
1
2
3
4
8/9/2010 Page 13 of 30
6 (8) #10 x 1-1/4” (8) Figure-8
Screw (4) Figure-8’s into the predrilled holes in
the bottom edge of the internal end panels.
1 2
8/9/2010 Page 14 of 30
7 (6) Cams
Fasten the internal end panels to the back legs.
1
2
3
4
8/9/2010 Page 15 of 30
8 (6) Cam pins
Screw (3) cam pins into each front leg.
1 2
8/9/2010 Page 16 of 30
9L (For chairs with a left hand tablet)
Attach the left hand tablet assembly to the left front leg.
1 2
8/9/2010 Page 17 of 30
9R (For chairs with a right hand tablet)
Attach the right hand tablet assembly to the right front leg.
1 2
8/9/2010 Page 18 of 30
10L (For chairs with a left hand tablet) (1) 5/16-18 x 4”
Attach an arm standoff and an arm plate to the right front leg.
(1) Barrel nut
1 2
8/9/2010 Page 19 of 30
10R (For chairs with a right hand tablet) (1) 5/16-18 x 4”
Attach an arm standoff and an arm plate to the left front leg.
(1) Barrel nut
1 2
8/9/2010 Page 20 of 30
11 (6) Cams
Fasten the front legs to the internal end panels.
(All steps from this point forward show a chair
with a left hand tablet. The same steps are used
for a chair with a right hand tablet.)
1
2
3
4
8/9/2010 Page 21 of 30
12 (4) 5/16-18 x 1”
Attach the seat support beam to the front legs.
1 2
8/9/2010 Page 22 of 30
13 (20) Shoulder screws
Screw (4) shoulder screws into each end cover panel
and the back cover panel.
1 2
(2) LEFT (1) BAC
K
(2) RIGHT
8/9/2010 Page 23 of 30
14
Fasten the end cover panels to the internal end panels.
1 2 3
Turn the figure-8’s to hold the cover
panels in place.
8/9/2010 Page 24 of 30
15 (6) #12 x 5/8”
Fasten the bottom panel to the support beam
and the z-bar.
(FRONT)
(BACK)
8/9/2010 Page 25 of 30
16 (16) #12 X 3/4"
Fasten the arms to the arm plates.
1
2
(OUTSIDE)
(INSIDE)
8/9/2010 Page 26 of 30
17
Fasten the seat cushion to the back panel with
the clips and D-rings.
8/9/2010 Page 27 of 30
18 (4) #10 x 1-1/2”
Fasten the back cushion to the back panel.
8/9/2010 Page 28 of 30
19
Fasten the back cover panel to the internal back panel.
1 2 3
Turn the figure-8’s to hold the cover
panels in place.
8/9/2010 Page 29 of 30
20
To level the tablet (some parts have been hidden for clarity):
1. Loosen the (7) screws that attach the tablet base to the tablet plate.
2. Turn the set screws clockwise to raise the end of the tablet farthest from the leg. (see arrows)
3. Tighten the (7) screws that attach the tablet base to the tablet plate.
8/9/2010 Page 30 of 30
21
Assembly is complete. Adjust glides as needed.
Loading...