MySpot Installation Manual
Assembly instructions for all catalog numbers beginning with:
MS.M.2.39
MS.C.2.39
(Double seat with right hand and left hand tablets and with a 39” high back panel)
Tools required for assembly:
#2 Phillips screw driver
#3 Phillips screw driver
Slotted screw driver
5/32” hex wrench
3/16” hex wrench
6mm hex wrench
5/16” open end wrench
Hammer
Needle nose pliers
Power screw driver (optional)
8/9/2010 Page 1 of 35
Parts required to assemble (1) unit:
(1) – Back panel
(38-3/4”H x 68-3/4”W)
(2) – Outer back cover panels
(31-9/16”H x 31-7/8”W)
(2) – Inner back cover panels
(22-3/16”H x 31-7/8”W)
8/9/2010 Page 2 of 35
Parts required to assemble (1) unit (continued):
(2) – Internal end panels
(21-1/16”H x 22-1/2”W)
(2) – End right face cover panels
(21-3/16”H x 22-1/2”W)
(2) – End left face cover panels
(21-3/16”H x 22-1/2”W)
(1) – Seat support beam
(64-1/8”L)
8/9/2010 Page 3 of 35
Parts required to assemble (1) unit (continued):
(1) – Left front leg
(2-1/4”SQ x 24-3/16”H)
LH RH
(1 each) - Left hand and right hand tablet assembly
(1) – Left arm
(6”W x 28-1/2”L)
(1) – Right front leg
(2-1/4”SQ x 24-3/16”H)
(1) – Right arm
(6”W x 28-1/2”L)
8/9/2010 Page 4 of 35
Parts required to assemble (1) unit (continued):
(2) – Bottom panels
(23-5/8” x 27-3/8”)
(1) – Center table
(14-5/8”W x 25”D)
(2) – Back cushions
(2) – Z-bars (21-3/16”L)
8/9/2010 Page 5 of 35
(2) – Seat cushions
(4) – Pin-fast brackets
Hardware required to assemble (1) unit (shown actual size):
(8) 1/4-20 x 3/4” pan head machine screws – zinc (part# 1001501)
(4) 5/16-18 x 1” flat head socket cap screws – black (part# 26797)
(2) 1/4-20 x 85mm (3-3/8”) decorative head bolt – black (part# 26506-BLK)
(8) #12 x 3/4” flat head wood screws – zinc (part# 26791)
(14) #10 x 1-1/4” flat head wood screws – black (part# 1001591)
(2) #10 x 1-1/2” flat head wood screws – black (part# 1001592)
(8) #8 x 5/8” pan head wood screws – black (part# 1001742)
(18) #12 x 5/8” pan head wood screws – black (part# 4300-1738)
8/9/2010 Page 6 of 35
Hardware required to assemble (1) unit (shown actual size) (continued):
(4) #12 x 1” pan head wood screws – black (part# 1001739)
(32) #14 x 3/8” shoulder screws – zinc (part# 26794)
(12) Cam pins – nickel (part# 29989)
(2) Cam pins – nickel (part# 1000336)
(2) 1/4-20 barrel nut – steel (part# 20434)
(12) Cams – zinc (part# 29988)
(2) Cams – black (part# 1000335)
8/9/2010 Page 7 of 35
Hardware required to assemble (1) unit (shown actual size) (continued):
(14) Figure-8 fasteners – zinc (part# 1001663)
(4) Lock clips – black plastic (part# 1000611)
8/9/2010 Page 8 of 35
8/9/2010 Page 9 of 35
1 (6) #10 x 1-1/4” (6) Figure-8
Screw (6) Figure-8’s into the predrilled holes in
the bottom edge of the back panel.
1 2
8/9/2010 Page 10 of 35
2 (8) 1/4-20 x 3/4"
Attach the Z-bars onto the inside of the internal back panel.
1 2
8/9/2010 Page 11 of 35
3 (8) Shoulder screws
Screw (4) shoulder screws into both inner back cover panels.
1 2
8/9/2010 Page 12 of 35
4
Fasten the inner back cover panels to the back panel.
1 2 3
8/9/2010 Page 13 of 35
5 (8) #8 x 5/8” (4) Lock clips
Attach (2) lock clips under each inner back cover panel.
1 2 3 4
8/9/2010 Page 14 of 35
6 (2) Cam pins (6) Cam pins
Screw (3) cam pins into each back panel post and screw
(2) cam pins into the brass inserts in the back panel.
1 2
8/9/2010 Page 15 of 35
7 (8) #10 x 1-1/4” (8) Figure-8
Screw (4) Figure-8’s into the predrilled holes in
the bottom edge of the internal end panels.
1 2
8/9/2010 Page 16 of 35
8 (6) Cams
Fasten the internal end panels to the back panel posts.
1
2
3
4
8/9/2010 Page 17 of 35
9 (6) Cam pins
Screw (3) cam pins into each front leg.
1 2
8/9/2010 Page 18 of 35
10L
Attach the left hand tablet assembly to the left front leg.
1 2
8/9/2010 Page 19 of 35
10R
Attach the right hand tablet assembly to the right front leg.
1 2
8/9/2010 Page 20 of 35
11 (6) Cams
Fasten the front legs to the internal end panels.
1
2
3
4
8/9/2010 Page 21 of 35
12 (4) 5/16-18 x 1”
Attach the seat support beam to the front legs.
1 2
8/9/2010 Page 22 of 35
13 (16) Shoulder screws
Screw (4) shoulder screws into each end cover panel.
1 2
(2) LEFT (2) RIGHT
8/9/2010 Page 23 of 35
14
Fasten the end cover panels to the internal end panels.
1 2 3
Turn the figure-8’s to hold the cover
panels in place.
8/9/2010 Page 24 of 35
15 (10) #12 x 5/8”
Fasten the bottom panels to the support beam
and the z-bars.
(FRONT)
(BACK)
8/9/2010 Page 25 of 35
16 (4) #12 x 5/8"
Attach (2) Pin-fast brackets to the back panel.
8/9/2010 Page 26 of 35
17 (2) Cams (2) #10 x 1-1/2"
Fasten the center table to the back panel and
to the seat support beam.
5
1 2
3 4
(Turn cams)
8/9/2010 Page 27 of 35
18 (4) #12 x 5/8"
Attach a Pin-fast bracket to each arm.
1
2
3
(RIGHT)
(LEFT)
8/9/2010 Page 28 of 35
19 (4) #12 x 1” (8) #12 x 3/4"
Fasten the arms to the arm plates and the back panel posts.
1 1
2
2
8/9/2010 Page 29 of 35
20 (2) 1/4-20 x 85mm (2) Barrel nuts
Bolt the Pin-fast brackets to the back panel posts.
1 2
8/9/2010 Page 30 of 35
21 (8) Shoulder screws
Screw (4) shoulder screws into both outer back cover panels.
1 2
8/9/2010 Page 31 of 35
22
Fasten the outer back cover panels to the back panel.
1 2 3
Turn the figure-8’s to hold the cover
panels in place.
8/9/2010 Page 32 of 35
23
Fasten the seat cushions to the back panel with
the clips and D-rings.
8/9/2010 Page 33 of 35
24
Fasten the back cushions to the back panel with
the clips and D-rings.
8/9/2010 Page 34 of 35
25
To level the tablet (some parts have been hidden for clarity):
1. Loosen the (7) screws that attach the tablet base to the tablet plate.
2. Turn the set screws clockwise to raise the end of the tablet farthest from the leg. (see arrows)
3. Tighten the (7) screws that attach the tablet base to the tablet plate.
8/9/2010 Page 35 of 35
26
Assembly is complete. Adjust glides as needed.
Loading...