Wooyoung Telecom HL700M User Manual

U s e r’s Refere n c e

WOO YOUNG Telecom CO.,LTD.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or tele­vision reception, with can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one more of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not

expressly approved by the grantee or manufacturer could void the users
authority to operate such equipment.

Appendix A. Specifications

The specification of this monitor is subject to be changed without notice to improve perfor­mance.

Panel

Display
Resolution

Frequency

Sync Signal

Connectors

Tilting Degree (U/D)

Plug&Play

Power

Power Management

Environmental
Consideration

Dimensions

Weight

TFT active matrix

17 inch

337.92mm 270.336mm

0.264mm 0.264mm

8-bit (16,777,216 colors)
1280 1024@60Hz
1280 1024@75Hz

31.5~80KHz

56~75Hz
TTL, P. or N.

D-Sub 15pin connector

Speaker Input / Headphone Output (Audio Cable)

24pin Digital Cable

Audio Cable

RCA Cable

S-Video Cable

External TV Box(HL700MT Only)

-3 ~20 Degree

VESA DDC 1/2B

90~265VAC

Adapter DC 12V, 4.16A

VESA DPMS
0~40 C (32 F~104 F)
90% less

416mm(W) 409mm(H) 186mm(D)

5.2kg

3kg

Type

Pixel Pitch

Display Color

Basic

Maximum

Horizontal

Vertical

Input

Output
Consumption

Standby mode

Temperature

Humidity
Outside
Monitor

Carton

Size

1

Contents

1. Before Setting up 3

Brief Specification of LCD Monitor

3

In multimedia Model, added the below functions

3

Precautions

4

2. Items 6

3. Setting up the LCD monitor 8

Where is a good place to position the monitor? 8
Check before connecting the power cord and the signal cable !! 8
Monitor’s connectors (HL700A) 9
Monitor’s connectors (HL700M / MT) 10
Connecting Your LCD Monitor 11
Plug & Play 12
Warm-up Time 12

4. Adjusting The Monitor 13

The Function Control Buttons (HL700A) 13
How to use the Hot Key. (HL700A) 13
The Function Control Buttons (HL700M / MT) 14
How to use the Hot Key. (HL700M / MT) 14
Main OSD Menu 15
BRIGHTNESS/CONTRAST 15

2

POSITION &CLOCK/PHASE 16
COLOR 17
OSD MENU ADJUSTMENT & INPUT SOURCE 17
SETUP MENU 18
Input Source 18
Video1, Video2 19

5. Appendix 20

Appendix A. Specifications 20
Appendix B. 15-pin D-Sub Connector 21
Appendix C. 24-pin DVI Connector 22
Appendix D. DPMS Power Saving Mode 23

6. Troubleshooting 24

3

Before setting up

1

Resolution : 17.0 inch SXGA (1280 X 1024@75Hz)
Color display : 16,777,216 colors
DPMS (Display Power Management Signaling)
OSD (On Screen Display)
Auto Configuration : Hot key
Speaker [L + R : 3W + 3W = 6W (max)]
DDC 1/2B : Plug & Play

This is 17.0 inch TFT-LCD monitor. Before setting up the LCD Monitor, please read
this manual to help your understanding of the LCD Monitor.

Brief Specification of LCD Monitor

DVI(Digital Video Interface)
Composit video input
Composit Audio input
S-Video input
TV(HL700MT Only)

In Multimedia Model, added the below function:

According to PC system, DDC 1/2B may not be supported. If you meet Error
message,check your video card which compatibility with DDC. If you eant to know

more information, please contact our service center.

Notice

4

Do not use Ketone type material (ex.
Acetone), Ethyl Alcohol, Toluene, Ethyl
Acid or Methyl chloride, to clear the panel.
It might permanently damage the panel.

90V~265V

Check the voltage corresponds to the
local electrical supply before connecting
the AC power cord.

Never use the damaged AC power cord.

Keeps it away from stoves, heaters,
fireplaces and other sources of heat
and magnets.

Don’t put your LCD monitor in a location
with high humidity and dust.
Temperature : 0~40。C
Humidity : 90% less

Place the LCD monitor on a solid sur­face. If dropped, the screen can be
damaged easily.

Precautions

5

Don’t touch the screen with a acute nail
and pin

The LCD monitor can be damaged easi­ly by shock.

The LCD monitor consists of electrical
devices.
If the LCD monitor is damaged, contact
immediately our service center.

Don’t use your LCD monitor under
direct sunlight.

If you don’t use the LCD monitor for a
long time, unplug the LCD monitor.

6

Items

LCD MonitorUser Manual

2

How to fold stand

If you need to fold stand for movimg. please refer to the below picture.
To fold stand, you must down lever, and you can fold stand.

Notice

7

Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.

Notice

15-pin D-Sub Signal Cable

Audio Cable RCA Cable

S-Video Cable

DC Adapter

24pin Digital Cable(Option)

External TV Box (HL700MT Only)

8

Setting up the LCD monitor

3

Place the LCD monitor on a solid and flat surface. If dropped, the screen can be dam­aged easily.

Turn off the PC power before connecting the power cord and signal cable to the LCD
monitor.

Where is a good place to position the monitor?

Check before connecting the power cord and the signal cable !!

9

Monitor’s connectors (HL700A)

1

3

4

2

PC 15-pin D-Sub Signal Cable

DC Adaptor

Audio Cable

External Speaker

DC12V

PC AUDIO IN

SPK OUT

No.

Cable connectionsName

10

PC VIDEO

1 DVI Digital Video Cable(option) 6 AUDIO(R) Audio output(R) (Red)

2PC

15-pin D-Sub Signal Cable

7 AUDIO(L) Audio output(L) (White)

3 DC12V

DC Adapter

8 VIDEO1 DVD/VCR Cable (Yellow)

4

PC AUDIO IN

Speaker Cable 9 Ext.

External TV Box (HL700MT Only)

5 SPK OUT External Speaker Cable 10 VIDEO2

S-Videl Cable

No. Name Cable connections No. Name Cable connections

Monitor’s connectors (HL700A)

11

Connecting your PC system

1. Connect the 15-pin D-Sub Signal Cable from PC to No.1.

2. If you use a speaker, connect the Audio Cable from PC to No.3.

3. If you use a headphone and earphone, connect the Headphone Cable from PC to
No.4.

Connecting Your LCD Monitor

Connecting your PC system

1. Connect the 15-pin D-Sub Signal Cable from PC to No.2.

2. If you have a DVI compliant video graphics adaptor, connect Digital Video Cable from

PC to No.1.

3. If you use a speaker, connect the Audio Cable from PC to No.4.

4. If you use a headphone and earphone, connect the Headphone Cable from PC to

No.5.

Connecting your AV(DVD, VIDEO, CAMCODER) & TV

1. Connect the DVD/VCR Cable from PC to No.6, No.7 and No.8.

2. Connect the external TV box cable to NO.9.

3. Connect the S-Video cable to NO.10.

FCC RF
INTERFERENCE STATEMENT

NOTE :

This equipment tas been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment renerates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to redio commuications. Operation of this equipment in a residential
area is likely to cause hamful interference in which case the will be required to correct the
interference at his own expense.

For HL700A

For HL700M /MT

12

The adoption of the new VESA Plug and Play solution eliminates complicated and
time consuming setup. It allows you to install your monitor in a Plug and Play compati­ble system without the usual hassles and confusion. Your PC system can easily identi­fy and configure itself for use with your display. This monitor automatically tells the PC
system its Extended Display Identification Data (EDID) using Display Data Channel
(DDC) protocols so the PC system can automatically configure itself to use the flat
panel display.

All LCD monitors need time to become thermally stable whenever you turn on the
monitor after letting the monitor be turned off for a couple of hours. Therefore, to
achieve more accurate adjustments for parameters, allow the LCD monitor to be
warmed up for at least 20 minutes before making any screen adjustments.

Plug & Play

Warm-up Time

Connecting for TV

Connect the external TV Box to Monitors Ext. jack
Connect the antenna cable to the external TV Box from wall antenna jack same as the

below the picture

13

Adjusting The Monitor

4

MUTE AUTO MENU SELECT VOLUME

The Function Control Buttons (HL700A)

How to use the Hot Key. (HL700A)

Sound Mute On/Off button.

MUTE

You can adjust brightness or contrast as not key. When display
adjust menu, you can adjust with Left/Right button arrow button.

When you push the Left/Right button, you can adjust the
volume.

VOLUME

OSD menu On/Off button.

MENU

When you push Auto button, this will optimize image quality automati­cally.

AUTO

Power On/Off toggle button.

Menu select button.

SELECT

14

MUTE AUTO/SELECT MENU MODE VOLUME

The Function Control Buttons (HL700M / MT)

How to use the Hot Key. (HL700M / MT)

Sound Mute On/Off button.

MUTE

You can adjust brightness or contrast as not key. When display
adjust menu, you can adjust with Left/Right button arrow button.

When you push the Left/Right button, you can adjust the
volume.

VOLUME

OSD menu On/Off button.

MENU

When you push Auto button, this will optimize image quality automati­cally.

AUTO/SELECT

Power On/Off toggle button.

Menu select button.

MODE

Notice :

Notice : In MENU, the button is “SELECT”function

15

When you push the menu button, you can see below main OSD menu.

Brightness : Changes the overall light intensity of the images being displayed.
Contrast : Changes the ratio of light intensity between the brightest white and dark-

est black.
You can adjust brightness/contrast values that you want by this hot key.
Gamma : Change the gamma value.

Main OSD Menu

BRIGHTNESS/CONTRAST

MAIN MENU

BRIGHTNESS/CONTRAST

COLOR
POSITION
OSD
SETUP
EXIT

BRIGHTNESS / CONTRAST

BRIGHTNESS 50

CONTRAST
GAMMA

EXIT

Adjusting Gamma Value is useful in case of game or movie screen.

Notice

MAIN MENU

BRIGHTNESS/CONTRAST
COLOR
POSITION
OSD
SETUP
EXIT

16

MAIN MENU

BRIGHTNESS/CONTRAST
COLOR

POSITION

OSD
SETUP
EXIT

POSITION

HORIZONTAL 50

VERTICAL
CLOCK
PHASE

EXIT

CLOCK/PHASE

When image is not clear, you can use clock/phase menu.
PHASE/ CLOCK : Although ‘Auto Adjustment’ automatically finds the optimum val-

ues of Clock and Phase parameters as well as image position, it
may be necessary for you to adjust those parameters manually.
It is recommended for you to use ‘Auto Adjustment’ first. If the
adjustment results are not satisfactory, then use Clock and
Phase adjustment features to get the best adjustment results.
Bear in mind that Clock and Phase adjustment may change the
width of the image and affect image position as well. If the image
is clear while out of center by a couple of pixels, use image posi­tion to center the image.

POSITION & CLOCK/PHASE

POSITION

Changes the location of the image.
H-Position : Moves to the Left/Right
V-Position : Moves to the Bottom/Top

If image is not clear (noise), you can adjust Clock/Phase.

Notice

17

COLOR

The tone of color can be changed form bluish white to reddish white.
Color1 - Blue type
Color2 - Red type
RED, GREEN, BLUE - You can adjust red, green and blue values that you want.

MAIN MENU

BRIGHTNESS/CONTRAST

COLOR

POSITION
OSD
SETUP
EXIT

COLOR

COLOR1 COLOR2

RED 50

GREEN
BLUE

EXIT

OSD MENU ADJUSTMENT & INPUT SOURCE

Sets the OSD menu display position.
OSD Position : Moves the OSD menu to the horizontal or vertical direction.
OSD TIME : Shows the OSD TIME displays from 5 to 60sec.
LANGUAGE : Select language in OSD menu.

MAIN MENU

BRIGHTNESS/CONTRAST
COLOR
POSITION

OSDT

SETUP
EXIT

OSD

OSD POSITION

OSD TIME 30 SEC

LANGUAGE

ENGLISH

EXIT

18

SETUP MENU

Auto balance : Automatic adjust color (white level) for various input source’s white

level.
Input source : display input signal.
Information : display monitor’s information.
Recall : Discards current setting and replaced all paramotors with the factory

default values.

Input Source (HL700M / MT)

INPUT SOURCE : Selects input signal.
(PC DIGITAL VIDEO1 VIDEO2 TV)

MAIN MENU

BRIGHTNESS/CONTRAST
COLOR
POSITION
OSD

SETUPT

EXIT

SETUP

AUTO BALANCE SELECT

INPUT SOURCE PC

INFORMATION

SELECT

RECALL

SELECT

EXIT

The mode button can adjust Input Source by hot key.

In this case, the mode change time spend 2~3sec.

Notice

19

The mode button can adjust Input Source by hot key.

In this case, the mode change time spend 2~3sec.

Notice

VIDEO1, VIDEO2 (HL700M / MT)

MAIN MENU

BRIGHTNESS / CONTRAST

COLOR

CHANNEL
SETUP
EXIT

COLOR

SHARPNESS

COLOR
TINT
EXIT

BRIGHTNESS / CONTRAST : Increase or decreases the
light intensity of the screen / increase or decrease the
ratio of the light intensity between the brightest white and
the darkest black.
COLOR : Refer to below color menu.
CHANNEL : Refer to below channel menu.

(TV installation)
SETUP : Refer to OSD menu adjustment.
EXIT : Finish the current status.

SHARPNESS : Make image of the VIDEO/TV looked

sharper.
COLOR : Adjust color intensity of the VIDEO/TV.
TINT : Adjust a color tone of the VIDEO/TV.
SETUP : Refer to OSD menu adjustment.

MAIN MENU

COLOR

CHANNEL

AIR/CATV
AUTO CHANNEL
MANUAL CHANNEL
EXIT

AIR/CATV : Select AIR or CATV.
AUTO CHANNEL : Search the channel automatically.

(SELECT button

button : select channel

SELECT button (ADD/DEL))
MANUAL CHANNEL : Search the channel manually.
FINE : Adjust image quality of the TV.

CHANNEL

20

Appendix

5

Appendix A. Display Modes

Mode

VGA

SVGA

XGA

SXGA

640 X 480

720 X 400

800 X 600

1024 X 768

1280 X 1024

Resolution

31.468

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

Pixel Clock

Frequency(MHz)

Sync

Polarity(H/V)

31.468

35.000

37.500

37.879

48.077

46.875

48.363

56.476

60.023

70.087

59.940

66.670

75.000

60.300

72.188

75.000

60.004

70.000

75.029

28.322

25.175

30.240

31.500

40.000

50.000

49.500

65.000

75.000

78.750

-/+

-/-

-/-

-/-

+/+

+/+

+/+

-/-

-/-

+/+

21

Appendix B. 15-pin D-Sub Connector

Input signal : Analog RGB
15-pin D-Sub connector

15pin D-Sub Signal Cable

Pin No.

1

3

4

2

Analog Red Input

Analog Green Input

Analog Blue Input

Ground

5

Pin No.

6

8

9

7

10

DDC Ground

Signal Name

Analog Red Ground

Analog Green Ground

Analog Blue Ground

No Connect

Sync Ground

Signal Name

Pin No.

11

13

14

12

15

Ground

DDC Data

Horizontal Sync

Vertical Sync

DDC Clock

Signal Name

22

Appendix C. 24-pin DVI Connector

Input signal : Digital
24-pin DVI connector

24pin Digital Cable

Pin No.

TMDS DATA2-

TMDS DATA2+

DGND

NC

Pin No.

NC

Signal Name

TMDS DATA1-

TMDS DATA1+

DGND

NC

NC

Signal Name Pin No.

TMDS DATA-

TMDS DATA+

DGND

NC

NC

DDC CLOCk +5V POWER DGND

DDC DATA AGND TMDS CLOCK+

Analog vertical Sync

NC TMDS CLOCK-

Signal Name

23

This monitor has a built-in power management system called DPMS Power Saving
Mode. This system saves energy by switching your monitor into a low-power mode
when it has not been used for a certain period of time. The available modes are “ON”,
“Standby”, “Suspend”, and “OFF”.

Appendix D. DPMS Power Saving Mode

ON

State

Stanby

mode

Stanby

mode

OFF

Active

H-sync

Inactive

Active

Inactive

Active

V-sync

Active

Inactive

Inactive

Active

RGB

Signal

Blanked

Blanked

Blanked

Power

Consumption

Under

40Watt

Less

than

5Watt

-

Recovery

Time

Green

Amber

Amber

Amber

LED Color and

Operting status

Within

2Sec

24

Troubleshooting

6

What you see

Ensure that the power cord is firmly connected and the LCD
monitor is on.

“out of range” message.

“No signal input” message.

Screen is blank and power indictor
is off.

Check the maximum resolution and the frequency of the
video adaptor.

Compare these values with the data in the Display Modes
Timing Chart.

Ensure that the signal cable is firmly connected to the PC
or video sources.

Ensure that the PC or video sources are turned on.

The image is too light or too dark.

Adjust the Brightness and Contrast.

Refer to the Brightness/Contrast

The image color is not good.

Adjust the Color

Refer to the Color

Image is not centered on the
screen.

Executes Auto Configuration.

Screen is blank and power indicator
light is steady amber or blinks.

The monitor is using its power management system.

Move the computer’s mouse or press a key on the key­board.

Image is not stable and may
appear to vibrate.

Check that the display resolution and frequency from your
PC or video board is an available mode for your monitor.
On your computer check : Control Panel, Display, Settings

Note : Your monitor supports multiscan display functions

within the following frequency domain:

Horizontal frequency : 31~80KHz

Vertical frequency : 56~75Hz

Maximum refresh rate : 1280 x 1024 @75Hz

Suggested Actions

WOO YOUNG Telecom CO.,LTD.

h t t p : / / w w w . w y t . c o . k r

P/N : 97E9500117