Page 1
http://www.woosim.com
MODEL WSP-i250
(2inch Industrial Printer)
Rev. 1.0
WOOSIM SYSTEMS Inc.
#501, Daerung Technotown 3th,
448, Gasan-Dong, GeumChun-Ku,
Seoul, Korea
Tel : +82-2-2107-3700
Fax : +82-2-2107-3707
URL: http://www.woosim.com
All specifications are subjected to change without notice
Page 2
WSP-i250 Rev. 1.0
http://www.woosim.com
2
¦ Copyright
WSP-i250 2inch Industrial printer operator’ s man u al.
Copyright ⓒ2011 by Woosim Systems Inc.
All rights reserved.
The information contained in this manual is the p roperty of Woosim
Systems Inc .
And may not be reproduced in whole or in par t without the prior written
permission o f Woosim Systems Inc.
¦ Trademark
a registered trademark of Woosim Systems Inc.
All other trademark are t he properties of their respective companies.
¦ Caution
Some semiconductor devices are easily dam ag ed by static electric ity . You
should turn the printer “OFF”, before you connect or removed the cable on
the rear side, in order to guard the printer against the static electricity.
If the printer is damaged by the static electricity, you should turn the
printer “OFF”
¦ Notice
The contents of this manual are subject to change without notice.
Page 3
WSP-i250 Rev. 1.0
http://www.woosim.com
3
¦
Introduction
The WSP-i250 is the ideal so lution for Mo b ile banking system , Retail,
point of sales, Credit card Transaction, other traveling and mobile
computing etc.
The general features of WSP-i250 printer are as follows:
u Compact size (92.12×140.56×59.75mm)
u Light weight (406.5g) for true mobility [standard]
u Very silent printing thru direct thermal printing method
u High speed (80mm/sec, MAX)
u High resolution(203dpi : 8dots/mm).
u UART(RS-232C or TTL), Bluetoo t h Ver2.1 + EDR, USB[option]
Wireless LAN (IEEE802.11b/g)[option] interface
u Support Graphic LCD(128×32dots) with Blue LED Backlight
u Support Magnetic Stripe Reader [option]
u Support Smart Card Module [option]
u Support text and graphic printing
u Intutive LED’s indicate P o w er (o n/ o f f), Error
u Easier paper roll loading by CLAMSHELL design
u One touch paper cover
u Printer door open & Paper-out sensor
u Easier maintenance with self-diagnostic.
u In field programming – Update Firmware, Download Fonts and Logos
u Water-resistant construction.( IP54 – Certified )
u Microsoft Windows XP/VISTA/7/CE/Linux/Android compatible.
u Flow control : Software (XON/XOFF)
※ Hardware flow control not supported in printer.
u Free fall: 1.5 meter onto concrete
u Agency Approvals
Page 4
WSP-i250 Rev. 1.0
http://www.woosim.com
4
¦
Operating Precautions
Please follow the precautions below to enjoy and maintain the full performance of
the printer.
u
Using the Printer
● Be careful not to drop or bu mp the printer on a hard su r f a ce.
● Do not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as foll ows:
◆ Operating temperatur e :-10°C to 50°C
◆ Relative hum idity : 30% to 80%
● Do not install the printer near devices that gener a te strong
electromagnetic fields su ch a s a copy machine.
● Do not open the platen cover during printing .
● Do not remove or reinstall the communication cable during printing
or transmission.
● Do not touch the connectors of the communication during printing.
● Switch the POWER OFF when not in use.
● Do not use alcohol or other solvent.
● The AC adapter, the batter y ch a r ger and the battery pack ma y
become warm when in use. This is normal and is not a malfunction.
● When the battery pack is used at low temperature, the length of time
the printer can be used may be shortened.
u Thermal Paper Handling
● Store the thermal paper in a cool, dry and dark place.
● Do not rub the paper with hard objec t .
● Do not leave the paper with hard object.
● Do not allow plastic film, erasers, or adhesive ta pe to touch the paper
for long periods.
● Do not stack the therma l paper with diazo copies immediately
after copying or wet-type copies.
● Do not use chemical glue.
● Always use the clean the r mal paper.
Page 5
WSP-i250 Rev. 1.0
http://www.woosim.com
5
¦
Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
These equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception , which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Page 6
WSP-i250 Rev. 1.0
http://www.woosim.com
6
CONTENTS
1. Outline. .........................................................................................................................................8
1.1. Model classifications. .......................................................................................................8
1.2 Product Part Number System ..........................................................................................8
1.3. Specifications. ....................................................................................................................9
2. Setting up the printer. ............................................................................................................ 11
2.1. Printer & Accessories ..................................................................................................... 11
2.2. Printer Features ............................................................................................................... 12
2.3. Dimensions ....................................................................................................................... 13
2.4. Replacing paper roll. ....................................................................................................... 14
2.5. Power s u p ply .................................................................................................................... 15
2.5.1. Specified power supply ....................................................................................... 15
2.5.2. Installing the SAM Card and the battery ........................................................ 15
2.5.3. Recharging the battery pack .............................................................................. 16
2.6. Set operation mode ....................................................................................................... 17
2.6.1. GAP/HOLE SENSOR SETTING ............................................................................ 18
2.7. Confirmation of the Wireless-LAN information ........................................................ 20
2.7.1. MAC Address printing ......................................................................................... 20
2.7.2. Confirmation of the Wireless-LAN setting information ................................ 20
3. Interface ...................................................................................................................................... 21
3.1. UART(RS-232C or TTL) or USB ...................................................................................... 21
3.2. Bluetooth .......................................................................................................................... 23
3.3. Wireless LAN .................................................................................................................... 23
3.4. Card Reading & Smart Card insert .............................................................................. 24
4. Smart Card Module ................................................................................................................. 25
4.1. General Spec. ................................................................................................................... 25
4.2. Communication Protocol Sequence ............................................................................ 26
4.2.1. Regular Operation ................................................................................................ 26
4.2.2. Irregular Operation (Communication Error)
.................................................... 26
5. Using the printer ...................................................................................................................... 27
Page 7
WSP-i250 Rev. 1.0
http://www.woosim.com
7
5.1. Control panel. .................................................................................................................. 27
5.2. The self test ...................................................................................................................... 28
5.3. Using the Accessory ....................................................................................................... 28
5.3.1. Using the Shoulder strap .................................................................................... 28
5.3.2. Using the Belt clip ............................................................................................... 29
6. Consumable Parts. ................................................................................................................... 30
6.1. Recommended paper. .................................................................................................... 30
6.2. Printing position. ............................................................................................................. 30
7. Revision History ....................................................................................................................... 31
Page 8
WSP-i250 Rev. 1.0
http://www.woosim.com
8
11.. OOuuttlliinnee..
11..11.. MMooddeell ccllaassssiiffiiccaattiioonnss..
11..22 PPrroodduucctt PPaarrtt NNuummbbeerr SSyysstteem
m
WSP-i250 ( ) ( )
Model
Interface
A1 : UART/Bluetooth
(Standard)
Power
None : DC 8.4V
Model name / Interface Spec.
Example) 1. Porti-S40 Serial/Bluetooth Part No. ⇒ S40/A1
2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1
S40
SC30
W25
.
.
.
Wired Wireless
A RS-232C 1 Bluetooth
B TTL 2 IrDA
C USB 3
Wireless LAN
D RS-485 0 None
E Parallel
Z None
Page 9
WSP-i250 Rev. 1.0
http://www.woosim.com
9
11..33.. SSppeecciiffiiccaattiioonnss..
Item Specifications
Print method Direct thermal line printing
Characters per line 42cpl (MAX)
Character size Eng: 9*24dots, 12*24dots Kor: 16*24dots, [24*24dots]
Optional Characters
Simplified/Traditional Chinese, Arabic, Cyrillic, Russian,
Tukish, Greek , Japanese, Persian, Latin9 and
Others upon request.
Resolution 203dpi, 8dots/mm
Print width 2-inch (48mm, 384dots)
Print speed 80mm / sec (MAX)
Dimension
92.12 x 140.56 x 59.75mm (Standard)
92.12 x 144.47 x 59.75mm (MSR option)
Weight
(Including bat t ery)
406.5g (Standard)
413.5g (MSR option)
Interface
UART(RS-232C or TTL), Bluetooth Ver 2.1 + EDR,
USB[option], Wireless LAN interface(IEEE802.11b/g) [option]
Paper roll Thermal roll paper (58m m w id e, 50ø)
Barcodes
1-dimension : Code128, Code39, I2/5, Code93
UPC, EAN, KAN,
JAN, CODABAR
2-dimension : PDF417, QR Code, DATA Matrix, Micro PDF417,
Truncated PDF417
Driver
Microsoft Widows XP / VISTA / 7
Windows CE, Linux, Android OS driver compatible
Black mark Support black mark detection
H/W Spec MCU : 32bits RISC, FLASH : 4M bytes, RAM : 8M bytes
Receive buffer size 1M bytes
MSR [option] ISO 7810 / 7811 / 7812 Triple tracks(1&2&3) Reading
( Continue⋯ )
Page 10
WSP-i250 Rev. 1.0
http://www.woosim.com
10
Item Specifications
Smart Card Module
[option]
ISO 7816 Compliant (EMV level 1 Certified) /
T=0, T=1 support / 1 SAM (Security Application Module)
LCD
128×32 Dots FSTN (Blue LED Backlight)
Battery Rechargeable 7.4V DC, 1400mAh/1800mAh/2200mAh (Li-ion)
Battery duration 1 hour continuous printing
Battery charger
Input (100~250V AC, 50~60Hz)
Output(8.4VDC/0.8A), 4hours full charge time
Environment
conditions
Temperature
-10°C ~ 50°C (operating)
-10°C ~ 70°C (storage)
Humidity
30% - 80% (operating)
10% - 90% (storage)
MCBF(Mean Cycle
Between Failure)
Mechanical 37,000,000 lines
Head Approximately 50 Km
< Table 1 >
Page 11
WSP-i250 Rev. 1.0
http://www.woosim.com
11
22.. SSeettttiinngg uupp tthhee pprriinntteerr..
22..11.. PPrriinntteerr && AAcccceessssoorriieess
Your printer box should include these items. If any items are damaged or
missing, please contact your dealer for assistance.
WSP-i250
Battery Pack
▼ OPTIONAL
Communica t i o n cable
Shoulder strap
MSR
Thermal roll paper
Battery charger adaptor
Belt clip
1 SAM
Smart Card
Page 12
WSP-i250 Rev. 1.0
http://www.woosim.com
12
22..22.. PPrriinntteerr FFeeaattuurreess
▶ Part Name
Page 13
WSP-i250 Rev. 1.0
http://www.woosim.com
13
22..33.. DDiimmeennssiioonnss
Page 14
WSP-i250 Rev. 1.0
http://www.woosim.com
14
22..44.. RReeppllaacciinngg ppaappeerr rroollll..
1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow
direction like the picture.
3. Insert a new paper roll as shown.
4. Tear the excess paper off using the edge of paper door as a tear bar.
Note : Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the
printer can not detect the paper end correctly.
Page 15
WSP-i250 Rev. 1.0
http://www.woosim.com
15
22..55.. PPoowweerr ssuuppppllyy
22..55..11.. SSppeecciiffiieedd ppoowweerr ssuuppppllyy
22..55..22.. IInnssttaalllliinngg tthhee SSAAMM CCaarrdd aanndd tthhee bbaatttteerryy
① To install SAM card, proceed as follows:
-Insert the SAM card in the direction of the arrow.
② To install Battery Pack, proceed as follows:
-Insert the Battery Pack in the d irect io n of the arrow.
The following specification is requested for Power supply.
Battery Charger : DC 8.4V/0.8A
Avoid using power supply which its power capacity of power current is extremely high.
NOTE : ● Before installing or removing the battery pack, ensure the
printer is OF F.
● If the printer is not used for long period of time, remove the battery
pack from the prin t er .
Page 16
WSP-i250 Rev. 1.0
http://www.woosim.com
16
22..55..33.. RReecchhaarrggiinngg tthhee bbaatttteerryy ppaacckk
For recharging the battery pack, install the battery pack in the printer.
Insert the Battery Charger to the charge connector of the printer.
NOTE : ● While charging the printer, turn off the printer power.
● Do not remove the battery during charging.
● The batte ry is consumable parts and when purchasing, compared to
the use hour is gradually decreases. (Warranty 6 month)
● If the printer is not used for a long time, unplug the power cord
from the printer and outlet.
● The recharging time depends on the voltage level and ambient
temperature o f the battery. Normally, if takes about 4 to 5 hours to
recharge a battery pack.
● You must use only the supplied adapter.
● Red Lamp : charging the battery.
Green Lamp: charging is finished.
Page 17
WSP-i250 Rev. 1.0
http://www.woosim.com
17
22..66.. SSeett ooppeerraattiioonn mmooddee
In keeping on press ing the Feed and Power button s imultaneously until after the ERROR
lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(refer Table 2)
l FEED button : changing Printer MODE status.
l POWER button : changing OPTION status.
[Example] The defaults of the printer are :
UART / 9600 bps / 8 data bit / N o parity /1 stop bit / Density low /
Quality low / Mark use / Sensor low / Power down 5 minute
If a user wants to modify the defaults with
Bluetooth / 57,600 bps / 7 dat a bit / Odd pari ty /2 stop bit / Density high /
Quality high/ Mark Gap/Hole / Sensor Auto / Power down no use
u Press MODE & POWER Button during the Error Lamp flickers 5 times.
→
You will see present COMMUNICATION mode in the LCD. (UART)
→
Press the POWER Button twice. And then , interface mode has set to
Bluetooth mode.
u When you press FEED button once.
→
You will see present BAUD RATE mode in the LCD. (9600 bps)
→
Press POWER Button 3 times. And then, BAUD RATE has set to 57,600 bps.
u When you press FEED button once.
→
You will see present DATA BIT mode in the LCD. (8 Data bit)
→
Press POWER Button once. And then Data Bit has set to 7 DATA BIT.
u When you press FEED button once.
→
You will see present PARITY mode in the LCD. (N o parit y)
→
Press POWER Button once. And then the Parity bit has set to ODD Parity Bit..
u When you press FEED button once.
→
You will see present STOP BIT mode in the LCD . (1 stop bit)
→
Press POWER Button once. And th en the density has set to 2 Stop bit.
Page 18
WSP-i250 Rev. 1.0
http://www.woosim.com
18
22..66..11.. GGAAPP//HHOOLLEE SSEENNSSOORR SSEETTTTIINNGG
After setting GAP/HOLE of MARK and AUTO of SENSOR, the printer is required to save
the sensing Gap/Hole so please press the buttons by self-test way and keep pressing the
feed-button only and you can see "sensor setting" on LCD after the self-test ends up and
you can finish pressing th e f eed-button until after passing the 3rd label.
u When you press FEED button once.
→
You will see present DENSITY mode in the LCD. (Densit y lo w)
→
Press POWER Button twice. And th en the density has set to Density high.
u When you press FEED button once.
→
You will see present Quality mode in the LCD. (Low)
→
Press POWER Button once. And then the quality has set to Quality high.
u When you press FEED button once.
→
You will see present MARK mode in the LCD. (Use)
→
Press POWER Button once. And th en the mark has set to Mark Gap/Hole.
u When you press FEED button once.
→
You will see present SENSOR mode in the LCD. (Low)
→
Press POWER Button once. And then the sensor has set to
Sensor Auto.
u When you press FEED button once.
→
You will see present POWER DOWN mode in the LCD. (5 minutes)
→
Press POWER Button once. And th en the Power down has set t o
Power down no use.
If all the mode have set, press the POWER Button and the FEED Button
at the same time. After then release the buttons at the same time.
Bluetooth _ 57600bps _ 7 data bit _ Odd parit y _ 2 stop bit _ Density high
_ High_ Gap/Hole_ Auto _ No use
Page 19
WSP-i250 Rev. 1.0
http://www.woosim.com
19
MODE
OPTION
Bluetooth WLAN
Communication
Port
UART(RS-232C) UART(RS-232C)
Protocol UART
(RS-232C)
Protocol UAR T
(RS-232C)
Bluetooth
WLAN
Protocol Bluetooth Protocol WLAN
Baud Rate
9600 bps
19200 bps
38400 bps
57600 bps
115200 bps
Data Bit
7 Data bit
8 Data bit
Parity Bit
No Parity
Odd Parity
Even Parity
Stop Bit
1 Stop bit
2 Stop bit
Density
Density Low
Density Mediu m
Density High
Quality
Low
High
Mark
No use
Use
Gap / Hole
Continue⋯
Page 20
WSP-i250 Rev. 1.0
http://www.woosim.com
20
22..77.. CCoonnffiirrmmaattiioonn ooff tthhee WWiirreelleessss--LLAANN iinnffoorrmmaattiioonn
22..77..11.. MMAACC AAddddrreessss pprriinnttiinngg
22..77..22.. CCoonnffiirrmmaattiioonn ooff tthhee WWiirreelleessss--LLAANN sseettttiinngg iinnffoorrmmaattiioonn
MODE OPTION
Sensor
Low
Medium1
Medium2
High
Auto
Power Down
No use
1 minute
2 minute
3 minute
4 minute
5 minute
< Table 2 >
u MAC add ress which is s et to the printer c an be printed out in pressing th e Power
and Feed button simultaneously and taking off t hem shortly after the ERROR lamp
blinks
u Press the Power button in the printer turning on
As the Power lamp turns on, MAC Add r es s is indicated.
u IP Address on LCD is indicated in pressing the Power button once again
u Subnet mask on LCD is indicated in pressing the Power button once again
u Gateway IP on LCD is indicated in pressing the Power button once again
u DNS sever IP on LCD is indicated in pressing the Power button once again
※ Sin ce t he conf igur ation of Wi rele ss LA N ca n not be done with the printer in
person, you are required to use the Wireless LAN-setting program which
WOOSIM offer s
Page 21
WSP-i250 Rev. 1.0
http://www.woosim.com
21
33.. IInntteerrffaaccee
33..11.. UUAARRTT((RRSS--223322CC oorr TTTTLL)) oorr UUSSBB
The WSP-i250 printer has a UART(RS-232C or TTL) or USB interface and is
connected by means of a 5 pin mini USB socket. In the following table, the
signals present on the Mini- USB so cket are listed:
① UART(RS-232C or TTL)
Pin No. Name Direction Function
1 TxD Output Transmit Data
2 RxD Input Receive Data
3 CTS - 4 NC. - 5 GND - Ground
Page 22
WSP-i250 Rev. 1.0
http://www.woosim.com
22
② USB
Pin No. Name Function
1 VCC +5V
2 DM DATA “-”
3 DP DATA “+”
4 NC. 5 GND Ground
NOTE : ● When data receiving, when it removes the Communication
cable, it loses a data.
Page 23
WSP-i250 Rev. 1.0
http://www.woosim.com
23
33..22.. BBlluueettooootthh
33..33.. WWiirreelleessss LLAANN
Category Specification
Bluetooth Spec. Bluetooth Ver2.1 + EDR / Class2 (10m)
Frequency R a ng e 2.4GHz ISM BAND
Data Transmission Rate 57600bps Fixed.
Data bit 8 Data bit Fixed.
Parity bit No parity Fixed.
Stop bit 1 Stop bit Fixed.
Category Specification
Interface Network IEEE802.11b/g
Protocol
TCP, UDP, IP, ICMP, ARP, DHCP, PPPoE
DNS lookup, DDNS(Dynamic DNS), WEP
Communica t i o n Mode
T2S TCP Server Mode
COD TCP Client Mode
ATC
TCP Server / Client
(AT command emulation)
U2S UDP
Page 24
WSP-i250 Rev. 1.0
http://www.woosim.com
24
33..44.. CCaarrdd RReeaaddiinngg && SSmmaarrtt CCaarrdd iinnsseerrtt
Please take notice that Magnetic
Stripe Card should be swapped
in direction of arrow.
Card can be read in both
Insert the Smart Card into
slot with micro chip
facing down.
Page 25
WSP-i250 Rev. 1.0
http://www.woosim.com
25
44.. SSmmaarrtt CCaarrdd MMoodduullee
44..11.. GGeenneerraall SSppeecc..
u Contact Smart Card Reader Module for ISO/IEC-7816
u Support Asynchronous Protocol T=0,T=1
u Smart Card Connection
- Short Circuit Current Limitation
- 6KV ESD Protectio n o n whole Smart Ca rd In terface
- Connector : Friction Type with Smart Card presence detection
u 1 SAM (Secu rity Application Module)
u EMV Level 1 Certified
Page 26
WSP-i250 Rev. 1.0
http://www.woosim.com
26
44..22.. CCoommmmuunniiccaattiioonn PPrroottooccooll SSeeqquueennccee
44..22..11.. RReegguullaarr OOppeerraattiioonn
44..22..22.. IIrrrreegguullaarr OOppeerraattiioonn ((CCoommmmuunniiccaattiioonn EErrrroorr))
Command
Host
Module
Execution
Response
Command
Command
Host
Module
Command is
Command
Executio
500ms timeout
Command
Host
Module
CheckSumEr
Command
Executio
Error
Page 27
WSP-i250 Rev. 1.0
http://www.woosim.com
27
55.. UUssiinngg tthhee pprriinntteerr
55..11.. CCoonnttrrooll ppaanneell..
u
BUTTON
- FEED Button : When the printer is on, paper can be feed manually by pressing and
holding the FEED button for more than one second.
- POWER Button:
① When of 5 or more seconds presses and power comes to on or off.
② After pressing the POWER and the FEED button simultaneously, if the ERROR
lamp 5 turn signals POWER button is converted with MODE functions.
- In keeping on pressing the Feed and Power button simultaneously until after the
ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the
printer mode.
(Refer to 2.6. Set operation mode for details ab out mode conversion)
u
LAMP
- POWER lamp(GREEN) : Printer is ON and ready to receive data.
- ERROR lamp(RED) : Indicated a fault condition or a printer error.
(i.e : no paper, paper cover opened. etc.)
u
LCD
- LCD will display most of the printer status.
(i.e : current printer status, paper out, indicated remaining battery,
Bluetooth co nnection etc.)
Page 28
WSP-i250 Rev. 1.0
http://www.woosim.com
28
55..22.. TThhee sseellff tteesstt
55..33.. UUssiinngg tthhee AAcccceessssoorryy
55..33..11.. UUssiinngg tthhee SShhoouullddeerr ssttrraapp
The self test procedure will check most of the printer functions.
For self test, turn o n the power while h o ld in g down the FEED Button.
The Self-Test checks the following :
1) Make sure paper roll has been installed properly.
2) The Self-
Test prints the current printer status, which provides the
control ROM version and the communication method setting.
3) After printing the current printer status, Self-Test will print a pattern
using the built-in character set.
4) The Self-Test automatically ends.
The printer is ready to receive data as soon as it completed the self test.
Please sling it over your shoulder after
fixing the shoulder s trap to t he pr i n te r i n
the order of the illustration.
Page 29
WSP-i250 Rev. 1.0
http://www.woosim.com
29
55..33..22.. UUssiinngg tthhee BBeelltt cclliipp
Following the instruction of the arrow, please put the belt clip i n the hole and
turn and fix the screw to the right by using a thing like a coin.
Afterward, you can use it like the picture below.
Page 30
WSP-i250 Rev. 1.0
http://www.woosim.com
30
66.. CCoonnssuummaabbllee PPaarrttss..
66..11.. RReeccoommmmeennddeedd ppaappeerr..
66..22.. PPrriinnttiinngg ppoossiittiioonn..
Type : Thermal Paper
Paper width : 58mm
Paper thickness : 60±5
㎛
Outer diameter : Ø50mm or less
Recording side : Outside of roll
Cautions
1. Do not paste the paper to the core. And the roll paper which has
Near end mark printing on its near end is recommended.
2. Chemicals or oil may change the colo r o f p aper, or printed Charact ers
may fade.
3. Change of paper color starts from approx 70 ℃.
Pay attention to heat, humidity and sun light.
4. Color of paper may be changed by being scratched by nail or hard
metal, etc
Page 31
WSP-i250 Rev. 1.0
http://www.woosim.com
31
77.. RReevviissiioonn HHiissttoorryy
Date Version Comments
Mar. 08. 2011 1.0 Initialize
Loading...