Woodstock W1054 User guide

INSTRUCTIONS FOR ONE MACHINE
Page 1 of 2
UST COLLECTION HOOK-UP KIT
D
This dust collection kit allows one woodworking machine to be connected to a dust collector within close proximity. This kit includes: 1 – 10' section of 4" Flex-hose, 1 – Universal Dust Hood and 2 – Hose Clamps. If your dust collector inlet port is larger than 4", you will need to reduce to 4". Refer to the heating and cooling section at your local hard ware store for reducers.
Hood Set Up:
1. Attach the Universal Hood over your woodworking machine dust port with either double sided carpet tape, foam
mounting tape, or sheet metal screws. If using screws, pre-drill 4 screw holes in the hood flange. If your woodwork ing machine does not have a dust port, it will be necessary to make a modification.
-
-
One type of modification requires an intermediate mounting adapter to decrease the dust port opening. The need for an
intermediate adapter is necessary for open frame contractor type table saws and whenever an opening must be reduced to accommodate the Universal Hood. The intermediate adapter can be either a piece of thin plywood or sheet metal with a hole cutout. The cutout should be sized smaller than the Universal hood flange so that the hood will surface mount to the adapter.
A second modification type may require cutting a dust port hole in an enclosed stand where non exists. If cutting a
hole, locate it near the bottom of the compartment and away from the operator’s normal position. Surface mount the Universal Hood over the hole with double sided carpet tape, foam mounting tape or screws.
Stand modification showing intermediate adapter and hood placement.
Grounding:
2. It is important to properly ground your system against the risk of spark caused by static electricity. Since plastic is an
insulator, the movement of dry dust contacting the walls of the flex-hose will produce a static charge. This charge may build and eventually arc to the nearest ground. The resulting spark may cause a fire or explosion. To protect against static electric build-up, we strongly recommend the installation of an internal bare copper grounding wire (available from Woodstock International dealers). Fish the wire through the flex-hose and connect one end to the frame of your dust collector, making sure that metal to metal contact is made. Connect the other end to the frame of your woodworking machine. Ensure that your dust collector and woodworking machine are electrically grounded so that your machine frames provide a continuous ground for static electricity.
Internal ground wire connection to machine frame.
Stand modification showing hole cutout and hood placement.
Continued on other side
Page 2 of 2
INSTRUCTIONS FOR ONE MACHINE
UST COLLECTION HOOK-UP KIT
D
Hose Conenction:
3. Place a loosened wire hose clamp around one end of the flex-hose and slide the hose over the dust collector inlet
port. If the dust collector port is not 4", it will be necessary to provide a reducer of the correct size to make the connection. Tighten the hose clamp with a screw driver to secure the flex-hose to the dust collector.
4. Place the second wire hose clamp around the free end of the flex-hose and slide the hose over the Universal Dust
Hood. Secure the wire clamp with a screw driver.
5. Now, assuming that all safety precautions are observed, you are now ready to collect the dust produced by your
woodworking machine.
Woodstock International offers a full line of accessory dust collection components that can be added to this kit for a more elaborate system. For more information about dust collection and system design, please refer to our handbook: DUST COLLECTION BASICS – Recommendations for Home Shop Systems. This handbook and other dust collection compo nents are available through your Woodstock International dealer.
-
ADDITIONAL WOODSTOCK INTERNATIONAL DUST COLLECTION ACCESSORIES
The dust collection accessories included with this kit are for simple dust collection system hook-ups. More elaborate sys­tems are possible, but will require additional accessories. All the accessories included in this kit can be used in a larger, more complex system as described in the handbook DUST COLLECTION BASICS. Consult with your local Woodstock product retailer for these dust collection accessories.
W1001 61⁄2" Jointer Dust Hood W1002 81⁄2" Jointer Dust Hood W1003 Floor Sweep W1004 12" Table Saw Dust Hood W1005 14" Table Saw Dust Hood W1006 3" Blast Gate W1007 4" Blast Gate W1008 5" Blast Gate W1009 6" Blast Gate W1010 Universal Dust Hood W1011 4" to 3" Reducer W1012 3" T W1013 4" T W1014 3" Y W1015 3" Y W1016 3" Elbow W1017 4" Elbow W1018 3" Splice W1019 4" Splice W1020 3" to 2" Reducer W1021 3" Hose Clamp W1022 4" Hose Clamp
W1023 5" Hose Clamp W1024 6" Hose Clamp W1025 2" Hose Clamp W1026 2" x 10' Hose W1027 21⁄2" x 10' Hose W1028 3" x 10' Hose W1029 3" x 20' Hose W1030 3" x 50' Hose W1031 4" x 10' Hose W1032 4" x 20' Hose W1033 5" x 10' Hose W1034 4" x 10'
Hose
W1035 5" x 10'
Hose
W1036 6" x 10'
Hose
W1041 3" to 21⁄2" Reducer W1042 21⁄2" Universal Dust Port W1049 Large Dust Collection
Separator W1050 Dust Collection Basics (Book)
Clear, Wire-Reinforced
Clear, Wire-Reinforced
Clear, Wire-Reinforced
W1053 Dust Collection Grounding Kit W1054 Dust Collections Accessories Kit #1 W1055 Dust Collections Accessories Kit #2 W1141 3" Aluminum Blast Gate W1142 4" Aluminum Blast Gate W1315 2" Wire Hose Clamp W1316 3" Wire Hose Clamp W1317 4" Wire Hose Clamp W1318 5" Wire Hose Clamp W1319 6" Wire Hose Clamp W2026 2" x 10' Clear Hose W2027 21⁄2" x 10' Clear Hose W2028 3" x 10' Clear Hose W2031 4" x 10' Clear Hose W2032 4" x 20' Clear Hose W2033 5" x 10' Clear Hose W2046 21⁄2" Hose Adapter W2049 Small Dust Collection Separator
(for use with a Shop Vac® & a 5-gallon bucket)
922 © Woodstock International Feb. 1999
Loading...