Woodstock D3273 User Manual

Instruction Sheet

Model D3273

Gravity Feed Spray Gun

WARNING: NO PORTION OF THIS DOCUMENT MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

SEPTEMBER 2003, PRINTED IN CHINA.

INTRODUCTION

This gravity feed spray gun with a 1.4mm nozzle includes an in-line regulator for precise control and a chrome finish for easy clean-up.

SETUP

Attach the regulator to the base of the spray gun, then attach the airline to the regulator with a

⁄4 NPT fitting. Use the adjustment knob on the regulator to set the air pressure to 30 PSI.

ADJUSTMENTS

See Figure 1 to identify the location of the spray gun controls and adjust in the following order:

1. Fluid Control—Adjusts the trigger travel, which

affects the volume of paint released.

2. Air Flow Control—Adjusts the volume of air

that mixes with the paint, and thus, increases or decreases the paint atomization.

3. Pattern Control—Variably adjusts the spray

pattern from round to a wide fan.

4. Nozzle Control—Adjusts the spray pattern from

vertical to horizontal.

OPERATIONS

Hold the sprayer 6"–8" from the workpiece, and keep the spray gun perpendicular to the workpiece during strokes.

DO NOT pivot your wrist when

spraying!

MAINTENANCE

Clean the spray gun by flushing it with thinner; however,

DO NOT immerse the gun in the

thinner!

2. Regularly clean the filter between the

container and spray gun.

3. To avoid internal damage, only use the

included brush when cleaning inside the spray gun orifices.

Figure 1. Model D3273.

Fluid

Control

Nozzle

Control

Pattern Control

Included Regulator

Air Flow

Control

EXPLOSION HAZARD! Do not spray flammable fluids near an open flame or ignition source.

EYE INJURY AND RESPIRATORY HAZARD! Always use safety glasses and respirator rated for paint and solvent vapors while using sprayer.

CUSTOMER SERVICE

For questions contact Woodstock International Technical Support at (360) 734-3482, or send email to: tech-support@shopfox.biz.

D3273 Parts Diagram

REF PART # DESCRIPTION

01 XD3277001 SEAL WASHER 02 XD3277002 SWITCH KNOB 03 XD3277003 SWITCH POLE 04 XD3277004 LOCKED SPRING 05 XD3277005 NUT 06 XD3277006 WASHER 07 XD3277007 ATOMIZATION 08 XD3277008 FLUID NOZZLE 09 XD3277009 FLUID NOZZLE PLUG 10 XD3277010 WASHER 11 XD3277011 DIRECTION SCREW 12 XD3277012 WASHER 13 XD3277013 SPRING 14 XD3277014 TRIGGER PIN I 15 XD3277015 TRIGGER PIN II 16 XD3277016 TRIGGER 17 XD3277017 SNAP RETAINER 18 XD3277018 SNAP RETAINER 19 XD3277019 BREATHER PLUG 20 XD3277020 CONTAINER COVER 21 XD3277021 CONTAINER 22 XD3277022 FILTER 23 XD3277023 FLUID

REF PART # DESCRIPTION

24 XD3277024 SNAP RETAINER 25 XD3277025 O-RING 26 XD3277026 PATTERN ADJ. 27 XD3277027 COPPER WASHER 28 XD3277028 PATTERN ADJ. KNOB 29 XD3277029 PATTERN ADJ. SCREW 30 XD3277030 SCREW 31 XD3277031 FLUID ADJ. KNOB 32 XD3277032 JOINT CAP 33 XD3277033 FLUID NEEDLE SPRING 34 XD3277034 FLUID ADJ. NEEDLE 35 XD3277035 MODULATOR 36 XD3277036 SWITCH SPRING 37 XD3277037 SWITCH BLOCK 38 XD3277038 O-RING 39 XD3277039 SCREW 40 XD3277040 GUN BODY 41 XD3277041 AIR INLET PLUG 42 XD3277042 TOOL WRENCH 43 XD3277043 HEX WRENCH 44 XD3277044 BRUSH 45 D3279 REGULATOR

1514

1716

42 43

40 41