Page 1
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
WOODSON CONTACT TOASTER – SPLIT LID
Model WGPC62
FEATURES
Gas struts assist in lifting the top platen and hold open when operating
2 top plates (182 x 295mm) and one large bottom plate (393 x 295mm)
Full perimeter gutter with raised edges drain to lager removable front frease tray
Lift assst upper platens utilise gas struts to enable easy and safe lifting operationand ensure gentle
for optimal toasting
Eight programmable timer settings with one touch operation to achieve consistent results
Easy-clean PVC coated smooth metal conduit to route cables to upper cooking plate
Stainless steel switch protection guard for protection against accidental spilage
No hidden crevices for food accumulation – extremely easy to clean
Removable heat shield – clip-on, no tools required
All stainless steel body construction
Page 2
Page 3
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 1
Table of Contents
General Recommendations................................................................................3
Specifications...................................................................................................................4
Technical Specifications........................................................................................4
Technical/Connection Diagram ..............................................................................5
Rating Plate.........................................................................................................6
Installation.......................................................................................................7
General Precautions .........................................................................................................7
Setting Up.......................................................................................................................8
Handling..............................................................................................................8
Site Preparation ...................................................................................................8
Unpacking ...........................................................................................................8
First Time Operation.............................................................................................8
Electrical Connection........................................................................................................9
Operation.......................................................................................................10
General Recommendations .............................................................................................10
Introduction to Operation ...............................................................................................11
Product Overview...............................................................................................11
Operating Instructions....................................................................................................12
Setting the Timers..........................................................................................................14
Timer Adjustment...............................................................................................14
Temperature Adjustment................................................................................................15
After Hours....................................................................................................................15
Information .......................................................................................................15
Cleaning Procedure........................................................................................................15
Materials Required..............................................................................................15
Cleaning Procedure ............................................................................................16
External Surfaces...............................................................................................16
Internal Surfaces................................................................................................16
General Safety...............................................................................................................17
Service..............................................................................................................17
Sharp Edges ......................................................................................................17
Hot Surfaces......................................................................................................17
Power Cables.....................................................................................................17
Maintenance...................................................................................................18
Routines........................................................................................................................18
Schedules..........................................................................................................18
Log Books..........................................................................................................18
Inspection .........................................................................................................18
Faults................................................................................................................18
Stainless Steel Protection................................................................................................19
Cleaning............................................................................................................19
Corrosion Protection...........................................................................................19
Surface Finish....................................................................................................19
Water Damage ..............................................................................................................20
Information .......................................................................................................20
Access to Electrical Wiring and Mechanical Parts...................................................20
Replacements................................................................................................................21
Electronic Controller, Temperature Probe .............................................................21
Electrical Parts...................................................................................................21
Page 4
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 2
Mechanical Parts................................................................................................21
Servicing and Replacement Information Line....................................................................21
Troubleshooting..............................................................................................22
Electrical Diagrams .........................................................................................23
Spare Parts/ Assembly Diagram .......................................................................24
Warranty........................................................................................................25
Appendix 1 – Australian Warranty and Importer/Distributor Contact Details ........................25
Australian Warranty Policy & Procedure............................................................................25
WARRANTY REQUEST FORM...........................................................................................28
Page 5
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 3
WARNING!
The manufacturer cannot be held responsible for injuries or damages of an
y
kind occurred to persons, machine or others, due to lack of conformity with
the operation instructions indicated in this documentation and for abuse,
misuse and lack of conformity with the instructions indicated in thi
s
documentation as well as installation, uninstall, service, tune-up,
maintenance requirin
g
the removal of the safety barriers not performed B
Y
TRAINED AND AUTHORISED SPECIALISTS, will result in the IMMEDIATE LOSS
OF THE WARRANTY.
Loss of warranty will result from any service performed to the machine,
when:
o Safety barriers are removed without disconnectin
g
the power line and
the water supply. When any safety provision of the machine has been
bypassed, removed or excluded.
o Machine is installed in provisional, improper or unsafe conditions fo
r
lack of compliance with safety provisions (fuses, main breaker,
ground line, or water inlet and discharge valves).
When unauthorised modifications or unauthorised additions of
devices are made, which modify the operation cycles, indicated
on the data chart delivered with the machine.
o When non-genuine spare parts are used.
o Installation or stora
g
e in inadequate spaces according to the
indications of manufacturer.
o Machine utilization different from the scope foreseen as written in the
documentation (ex. Dishes of type or sizes different from specified).
o Utilization of dispensers with corrosive products.
General Recommendations
ATTENTION
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and
maintenance. Keep this booklet on hand in a safe place for future reference by other operators or service
technicians.
Do not store or use gasoline or other flammable vapours or liquids in the vicinity of this or any other appliance.
Qualified personnel, specifically trained in the following instructions, can perform installation and service of the
machine:
Page 6
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 4
Specifications
Technical Specifications
Safety Clearance
A clearance of 100mm should be maintained around the toaster.
Height when fully open approximately 625mm.
SPECIFICATIONS
Model WGPC62
Height 331mm
Width 455mm
Depth 578mm
Voltage 240v
Power 2200W
Current 10 A
Connection 10A Lead and Plug (Supplied)
Plate Size
Top 182mm x 295mm
Bottom 393mm x 295mm
Mass 35 kg
Capacity 4 Sandwiches
SHIPPING
Height 500mm
Width 600mm
Depth 700mm
Page 7
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 5
Technical/Connection Diagram
Page 8
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 6
Rating Plate
The rating plate of the appliance contains identification and technical data and is located on the unit as sh own
below.
Sample Only
Page 9
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 7
WARNING!
Installation must comply with local electrical and health & safety requirements.
Improper installation, adjustment, alteration, service or maintenance can cause
property damage, injury or death.
Installation
General Precautions
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions thoroughly before installation, maintenance
or servicing this equipment
Do NOT use this appliance for other than its intended use.
Do NOT store explosive substances such as aerosol cans with a flammable propellant in or near this
appliance.
Regulations require that all units be installed to the appropriate Australian standards.
Regulations require that authorised persons carry out all electrical work.
Only use this appliance with voltage specified on the rating label.
Be careful not to touch moving parts.
ATTENTION
Ensure that a trained person installs this machine.
Ensure the customer is trained on how to use the machine.
Ensure the customer is given the manual
Page 10
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 8
Setting Up
Handling
Use suitable means to move the appliance: eg. A lift truck or fork pallet trucks (the forks should
reach more than halfway beneath the appliance).
Site Preparation
Ensure the site is level and properly cleaned.
The toaster is to be placed on a suitable bench or worktop, at a comfortable working height. (850mm –
900mm)
Ensure the press toaster is placed on a level, stable work surface, away from other heat, water or grease
emitting devices.
Unpacking
Check the machine for damage before and after unpacking. If machine is damaged, contact the
dealer.
Wear protective gloves to unpack the appliance from the box.
The unit is supplied fully assembled.
Unpack and visually inspect the unit for damage or missing parts. Report any problems to the
distributor or manufacturer.
Remove all protective plastic film, tapes, ties and packers before installing and operating. Clean
off any glue residue left over from the protective plastic film.
Wipe all surfaces with a clean, sanitised cloth.
First Time Operation
Read the complete instruction manual before proceeding.
The toaster is preset in the factory with the following settings:
o Cooking temperature 246- 250 degrees C.
o The timers have been factory set to 12 seconds each.
o Refer to “Section 6 Setting the timers”
Plug the unit into a power source. Ensure the electrical cable is not damaged and does not hang over the
counter, and the “ON/OFF” button is set to the “OFF” position.
Your toaster is ready to use.
Page 11
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 9
Electrical Connection
WARNING!
This machine must be installed in accordance with AS/NZS 60335.1
Information
The electrical supply shall comply with the rating plate data.
The machine is supplied with a plug and lead (10A).
Ensure that machine is connected to a power point with compatible power rating of 240 volts 10 amps.
The machine must be plugged directly into the power outlet. The use of extension leads or power boards
are not to be used.
The equipment should be earthed according to local electrical codes to prevent the possibility of electrical
shock. It requires an earthed receptacle with separate electrical lines, protected by fuses or circuit
breaker of the proper rating.
If the supply cord is damaged, it MUST be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard. Power cable cannot be stretched kinked, pressed, during
normal operation, service or anytime
WARNING!
Some procedures in this manual require the power to the equipment to be turned off and
isolated. Turn the power OFF at the power point and unplug the power supply lead by the
plug body. If the power point is not readily accessible turn the equipment off at the isolation
switch or the circuit breaker in the switchboard. Attach a yellow “CAUTION-DO NOT
OPERATE” tag. This must be performed where relevant unless the procedures specify
otherwise.
FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.
Page 12
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 10
Operation
General Recommendations
When using any electrical appliance, safety precautions should always be observed.
Our appliances have been designed to give high performance. Hence, the appliance must be used exclusively for
the purpose for which it has been designed.
Read these instrucitons carefully and retain for future reference
All units MUST be installed according to the procedures stated in the installation section of this manual.
This appliance should not be operated by person/s (including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning the safe use of the appliance by person/s responsible for their safety.
In the case of new personnel, training is to be provided in advance.
Do NOT use this appliance for any other purpose than its intended use.
Do NOT store explosive substances such as aerosol cans with a flammable propellant in or near this
appliance.
The surfaces of this unit are HOT when in operation. Signage should be displayed for personnel and
customers.
Keep fingers out of "pinch point" areas. Clearances between the doors, pans and panels are necessarily
small.
This unit is NOT waterproof. Do NOT use jet sprays or hoses to the exterior of the appliance.
If the power supply cord becomes damaged, it must be replaced by the manufacturer, an authorised
service agent or similarly qualified persons to avoid a hazard.
Do NOT use machine if power supply cord is damaged.
Be careful not to touch moving parts.
Do NOT use sharp objects to activate controls.
If any fault is detected, disconnect the Split Lid – Contact Toaster from the mains, close the main water
supply and call the service agent.
Do NOT use the Split Lid – Contact Toaster in an explosive atmosphere.
Avoid exposure to direct heat and/or humidity sources.
The manufacturer declines any liability for damages to persons and/or things due and to an
improper/wrong and/or unreasonable use of the machine.
Page 13
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 11
Introduction to Operation
The Woodson Contact Toaster – Split Lid been specifically designed to meet the rigorous demands of a busy food
service operation.
Each Woodson Contact Toaster – Split Lid has been assembled and tested according to Stoddart’s strict quality
standards.
Product Overview
Configuration may vary according to model.
T
emperature/timer settings
ON/OFF switch
Bottom Platen
T
op Platen
T
op Platen
Handle
Page 14
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 12
Operating Instructions
1. Visually check the toaster is clean, in good repair and safe.
2. Ensure that the top platen is in a closed position.
3. Turn the power switch to the “ON” position. The power “ON” indication light located on the control panel
will be illuminated. If the indicator light does not illuminate refer to the trouble shooting section of the
manual.
4. Allow the press toaster to preheat for approximately 30 minutes. The temperature ready indicator light
will turn itself OFF once the press toaster has reached its optimum operating temperature. The press
toaster is preset to operate between 246°C - 250°C surface cooking temperature.
5. Ensure that the 8 display timers are set to the desired cook time on the control panel (
refer to
programming the toaster instructions in this manual).
6. Lift the top platen up to a fully open position by the handle provided.
7. The top platen will remain in the open position, as it is spring-loaded.
8. Take extreme care when lifting, do not touch the cover or cooking surface to avoid skin burns.
9. Place the food product onto the cooking surface and close the top platen.
10. Ensure that the product is placed in the middle of the cooking surface, to prevent the top platen from
tilting and producing uneven product.
11. Press the appropriate display timer button (i.e. 1,2,3,4,-1,2,3,4,) to start the cooking procedure. The time
shown in the window above the corresponding button will begin to count down.
12. Once the count down timer reaches “000”, the timer will emit a beeping sound. Press the appropriate
display timer button again, to de-activate the timer. Lift the top platen fully to the open position and
remove the toasted product.
NOTE!
Do not use the press toaster until the temperature ready light is off, as you will not
achieve optimum product quality results.
NOTE!
The timer can be stopped if necessary, by pressing the timer button and holding it for
3 seconds.
CAUTION!
The surfaces on this unit are hot!
Page 15
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 13
13.
Replace the top platens back in to the down position when the product has been removed.
14.
Periodically check the crumb tray mounted at the front of the press toaster, to ensure it does not overflow.
Take extreme care when removing the crumb tray, ensure you grab the crumb tray handle using heat
resistant gloves and do not touch the cooking surface to avoid skin burns.
NOTE!
To ensure optimum product quality, the top plate must be closed after every run, to
maintain constant temperature.
Page 16
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 14
Setting the Timers
The Control panel has 8 timers located along the front of the control panel. The displays indicate th e pre-
programmed times in minutes and seconds.
The unit is configured so that is equal to 1 minute 20 seconds.
Timer Adjustment
1. Press and hold Programme Button for 3-4 seconds.
2. Display 1 will flash.
3. Use the & arrow buttons to adjust time if necessary.
4. Press the Set button.
5. Repeat the above steps for the other display timer buttons if necessary (i.e. 1,2,3,4 -1,2,3,4,)
NOTE!
To change the times follow the steps below.
NOTE!
By pressing the programme button again, it will automatically go to the next timer
display in order of sequence, i.e. 1,2,3,4-1,2,3,4).
Page 17
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 15
NOTE!
After each cook wipe plates with moist cloth.
Temperature Adjustment
1. Locate the temperature calibrating screw on the rear of the toaster.
2. Open the top platen.
3. Measure the temperature of the bottom platen in a number of different areas.
4. Note the average temperature recorded.
5. Adjust the temperature adjusting screw a small amount.
6. Clockwise to increase temperature and anticlockwise to decrease temperature.
After Hours
Information
The unit MUST be switched OFF.
Cleaning Procedure
Clean Plates Daily (10 mins)
Materials Required
Cleaning Pad
Cleaning Pad Holder
Clean Sanitised Towel
Paper Towel
Small Container of hot water.
Grill Cleaning Gloves
Grill Cleaning Apron
IMPORTANT!
The temperature can only be ad
j
usted after the toaster has been turned on and allowed
to operate through 2-3 cycles.
Page 18
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 16
WARNING!
The external surfaces of this unit are NOT waterproof, do NOT hose.
WARNING!
DO NOT pour water directly onto the platen surface.
NOTE!
Toaster should be moved in front of operating grill exhausts to perform clean.
Cleaning Procedure
1. Turn toaster off and remove electric cord from power point
2. Wipe soil from the toaster using a clean sanitised towel and small amount of water to rinse the platens using a
damp cloth. Continually rinse the towel in hot water and thoroughly rinse all platens. Wipe over unit with a
clean dry cloth.
3. Remove crumb tray. Dry wipe crumb tray and then wash, rinse and sanitise. Air-dry and replace.
External Surfaces
Clean the stainless steel and metal parts with warm (not hot) soapy water and a sponge.
Rinsed the stainless steel and metal parts with clean, fresh water.
After cleaning, thoroughly wipe the stainless steel and metal parts dry with a soft cloth. Do NOT let water
pool on the unit. Check crevices and folds.
Internal Surfaces
Clean the internal surfaces with warm (not hot) soapy water and a sponge.
After cleaning, thoroughly wipe the stainless steel and elements with a soft cloth.
Page 19
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 17
General Safety
Service
Stoddart, one of our agents, or a similarly qualified person(s) should carry out any and all rep airs, maintenance
and services. Any repair person(s) should be instructed to read the safety warnings within this manual before
commencing work on these units.
Do not remove any cover panels that may be on the appliance.
Sharp Edges
Steel cutting processes such as those used in the construction of this appliance result in sharp edges. Whilst any
such edges are removed to the best of our ability it is always wise to take care when contacting any edge.
Particular care should be taken to avoid contact with any steel edge, and warnings should be given in regards to
the danger of such contact to any repair or maintenance person(s) prior to commencement of any servicing.
Hot Surfaces
This unit can get very hot. Ensure everyone is aware that the appliance is operating and take care to avoid
contact with hot surfaces.
Power Cables
Ensure that any damaged power cord is replaced before further use.
Page 20
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 18
WARNING!
If any electrical wires are damaged, the unit must NOT be switched
ON until the parts have been fixed as injury or death can occur.
Maintenance
Routines
Schedules
To maintain optimal performance, maintenance and cleaning schedules must be regular and thorough.
The unit should be cleaned at the end of every work day.
Log Books
Log books should be kept for all cleaning and maintenance of this unit.
Inspection
Surfaces should be checked at least once a week for damage or deterioration.
As part of the maintenance, a qualified technician MUST check the controls, mechanical parts and
electrical wiring for damage, deterioration or need of adjustment.
Faults
Not repairing small faults immediately can cause a complete breakdown. If any small faults occur, have
them attended to promptly by a qualified technician.
All faults should be reported to the distributor and manufacturer.
Page 21
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 19
Stainless Steel Protection
Cleaning
For cleaning a stain on the surface of the stainless steel, check the cleaning section of the operation
manual.
All metal surfaces should be checked while cleaning for damage, scuffs or scapes as these can lead to rust
and further damage to the product.
Corrosion Protection
Stainless steel exhibits good resistance to corrosion however, if not properly maintained stainless steel can
rust.
Any sign of mild rust or corrosion should be thoroughly cleaned with warm soapy water and dried as soon
as possible.
NEVER use abrasive pads or cleaners for cleaning.
Medium rust or corrosion can treated by a commercial cleaning agent that contains
citric/oxalic/nitric/phosphoric. Do NOT use cleaning agents with chlorides or other harsh chemicals as this
can cause corrosion. A lemon slice or a few drops few drops of lemon juice added to the water can be
used as a substitute. After treatment, wash with warm (not hot) soapy water and dry thoroughly.
Thoroughly wipe the surfaces dry after cleaning and do NOT let water pool on the unit. Check crevices and
folds for pooling.
If an abrasive product is used while cleaning, thoroughly dry the unit and leave in an open or oxidised
area for the stainless steel protective layer to replenish.
When using, ensure all liquids and moisture is cleaned up straight away. Food liquids such as juices from
vegetables and fruits should NOT be left on preparation surfaces.
Do NOT leave items on the stainless steel such as cutting boards, rubber mats and bottles.
Surface Finish
To protect the polish, stainless steel should be dried by wiping a dry soft cloth in the same direction as
grained polish.
For NON-food contact surfaces, a light oil can be wiped on the surfaces with a cloth to enhance the
stainless steel surface. Wipe in the direction of the grain.
Some commercial stainless stain cleaners can leave residue or film on the metal; this may trap fine
particles of food on the surface, thus deeming the surfaces not food safe.
Page 22
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 20
WARNING!
Maintenance of electrical or mechanical parts MUST be performed by a qualified
technician only
WARNING!
If any water damage occurs, the unit must NOT be switched ON.
WARNING!
Switch the unit OFF at the main power supply before any maintenance or
servicing.
CAUTION!
All due care has been taken in manufacturing, but there may be SHARP EDGES
around the internal sections.
Water Damage
Information
Water damage to the electrical and mechanical parts of unit can occur through hosing on or around the
unit.
Improper cleaning of the unit can lead to water damage. Check the cleaning section of the operation
manual for more information.
If water damage occurs allow the unit to dry and ensure the unit is checked by a qualified technician
before switching the unit ON.
All water damage that is not due to construction or mechanical faults is not covered by warranty.
Access to Electrical Wiring and Mechanical Parts
Page 23
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 21
Replacements
Electronic Controller, Temperature Probe
The electronic controller and temperature probe can be replaced by the manufacturer.
Both MUST be replaced by a qualified technician.
Electrical Parts
All electrical parts can be replaced by the manufacturer or others.
All electrical parts MUST be replaced by a qualified technician.
Mechanical Parts
All mechanical parts can be replaced by the manufacturer or others.
All mechanical parts MUST be replaced by a qualified technician.
Servicing and Replacement Information Line
All Parts
Stoddart Manufacturing:
Sales: 1300 791 954
Customer Service: 1300 307 289
Fax: (07) 3344 1000
Sales: [email protected]
Customer Service: [email protected]
Spare Parts: [email protected]
Page 24
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 22
Troubleshooting
Task Type - (O) = Operator (T) = Technician Task
Problem Possible Causes Task Possible Corrective Action
Not Heating
Unit not turned “on” at the
power socket.
O Turn power to “on” at the power socket on the wall.
Not Heating
“On/Off” switch on control
panel not turned on.
O Switch on power “on/off switch” on the control panel.
Not Heating Thermal Safety fuse blown T Call service technician.
Plates too Cold
Allow ready light to turn off
before cooking.
O
Plates too Cold
Temperature requires
adjusting.
T Refer to temperature adjustment in the manual
Plates too Hot
Temperature requires
adjusting.
T Refer to temperature adjustment in the manual
Plates not hot Element failure. T Test & replace the element if necessary.
WARNING!
Technician tasks only to be completed by qualified service people.
Check faults before calling service technician.
Page 25
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 23
Electrical Diagrams
Page 26
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 24
Spare Parts/ Assembly Diagram
Page 27
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 25
Warranty
Appendix 1 – Australian Warranty and Importer/Distributor Contact Details
As the exclusive manufacturer and distributor of Woodson products in Australia, Stoddart Manufacturing (Stoddart)
would like to congratulate you on your purchase of a Woodson product.
It should be noted by users of the product that it is not designed for household or domestic use and should not be
used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following
warnings are provided:
This product is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the product by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the product.
Users should also note that if the supply electricity cord is damaged in any way it should be replaced.
Please contact Stoddart for parts and we will advise how to do this in order to avoid any electrical hazard.
Australian Warranty Policy & Procedure
Stoddart is committed to providing a comprehensive and fair warranty for all of its equipment. The
warranty incorporates a commercial manufacturers’ warranty, together with the consumer warranty
provisions of the National Consumer Protection Act (2009).
1. Commercial Warranty
1.1 Stoddart warrants to the original purchaser ("Customer") of equipment manufactured or distributed by Stoddart that for 12
months from the date of installation of the equipment by Customer (the “Warranty Period”), any defect in workmanship or material will,
subject to clauses 1.2 and 3, be:
a) Repaired without charge; or
b) In respect of any Major Failure which cannot be repaired, replaced or the purchase money refunded.
1.2 Stoddart will not be liable for any associated loss, damage or compensation claim resulting from any defect in workmanship or
material, and such liability is expressly excluded from the operation of clause 1.1.
2. Consumer Warranty
2.1 Subject to clause 3, equipment supplied by Stoddart to Customer for personal, domestic or household use or consumption
comes with guarantees that cannot be excluded under the Australian Consumer Law. Customer is entitled to a replacement or refund for a
Major Failure and compensation for any other reasonably foreseeable loss or damage. Customer is entitled to have the equipment repaired,
or replaced if the equipment fails to be of an Acceptable Quality and that failure does not amount to a Major Failure.
3. Warranty Clarification
3.1 Customer acknowledges and agrees:
(i) A Major Failure occurs when the equipment suffers repeated and/or unexpected failure that cannot be repaired to
Stoddart's satisfaction (acting reasonably) or which Stoddart considers (acting reasonably) renders the equipment unsafe or inoperable;
(ii) Stoddart can only warrant the equipment will be of an Acceptable Quality when Customer uses the equipment in
accordance with Stoddart's manufacturer's instruct ions or user manual ("Instructions"). Acceptable Quality does not imply a lifetime
guarantee for the equipment;
(iii) Certain components have a finite expected life , especially in a commercial or high-use environment. For exam p le
components such as refrigeration compressors, elements, thermostats/simmerstat s, swit ches, fans, and temperature controllers can be
expected to last up to 12 months when used in accordance with the instructions;
(iv) In a commercial environment, components such as lamps, fluorescent tubes, light bulbs, glass, silicone seals, gaskets and
plastic components will require regular replacement. This is not covered by warranty and is at Customer's cost.;
(v) The life of equipment may be adversely affected by misuse, neglect, unautho rised alteration, incorrect installation, power
surges, accident, use of inappropriate chemicals, flooding, and acts of God;
Page 28
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 26
(vi) Proper maintenance and cleaning of equipment in accordance with the Instructions is essential to the equipment's effective
operation;
(vii) On site warranty services are limited to sites within 50km from the nearest Stoddart authorized service agent and serv ice
agent's reasonable travel costs must be paid by Customer p rior to the commencement of the repairs;
(viii) Additional labour costs will apply for service outsid e stand a rd business hours of 8.00am to 4:30pm, Monday to Friday and
on public holidays;
(ix) Stoddart cannot guarantee the performance of equipment made specifically to Customer's design or specifications.
Stoddart will, where reasonably possible, draw any issues arising from Customer's design or specifications to Customer's attention during the
commissioning and/or manufacturing process; and
(x) Customer must pay additional costs incurred by Stoddart as a result of Customer failing to provide suitable access to the
equipment for inspection and service.
3.2 Stoddart's warranty liability under clauses 1 and 2 of these Terms exclude or do not cover:
a) The matters acknowledged by Customer in clause 3.1;
b) Situations where Stoddart is not satisfied (acting reasonably) the equipment or any part of the equipment has been
used in accordance with the Instructions including misuse, neglect, unauthorised alteration, incorrect installation, power surges, accident, use
of inappropriate chemicals, flooding, fire or act of God;
c) Any consequential loss, damage or expense arising directly or indirectly from use of the equipment otherwise than in
accordance with the Instructions;
d) Any damage or malfunction arising from, or relating to, Customer's failure to properly maintain or clean the
equipment in accordance with the Instructions;
e) Damage caused to equipment during transportation, which is outside Stodd a rt's standard delivery conditions.
f) Breakage or replacement of lamps, fluorescent tubes, light bulbs, glass, silicone seals, gas kets and plastic
components.;
g) Maintenance, repair or other works not undertaken by a Stoddart authorised service agent
h) Where remote re frig erat ion is connected by a person other than Stoddart to equipment produced by Stoddart,
Stoddart cannot accept claims for repair of TX valves and control components, as the fault may arise from the installation of the remote
refrigeration lines, equipment, and gas, by a party over which Stoddart has no control.
i) Transportation costs associated with transporting the equipment to a Stoddart authorized service agent where
Stoddart considers (acting reasonably) that repairs cannot be undertaken on-site; and
j) Unless agreed to by Stoddart in writing to the con t rary, warranty is not included in the sale price for goods sold to or
installed in an overseas location.
Page 29
INSTALLATION,OPERATION & MAINTENANCE
Woodson Contact Toaster – Split Lid WGPC62
Tel: 1300 79 1954 Web: www.stoddart.com.au Email: [email protected]
Due to continuous product research and development, the information contained her ein is subject to change without notice
Page 27
4. Warranty Claim Procedure
The following procedure must be followed to claim under Stoddart's warranties:
a) Refer to the trouble-shooting section of the Instructions to establish the nature of the fault. Check the equipment is
plugged-in, turned-on or has no other valid reason for not operating.
b) If step (a) does not overcome the issue, you should report the fault with the equipment to our service department (phone
1300 307 289 or fax 07 3344 6166). Our service department will assist you with further trouble-shooting. If our service department is unable to
resolve the fault with the equipment they will request you complete a Stoddart Warranty Request Form and fax (fax 07 3 3 44 6166) or email
([email protected]) it to us.
c) To complete a Stoddart Warranty Request Form you will require the following informatio n:
i. Proof of purchase stating model number and date of purchase;
ii. The serial number of the equipment (this is located on the ratings plate sticker);
iii. A description of the fault/problem;
iv. Your company details including the exact location of the equipment; and
v. Any restrictions on times or methods of access to the equipment.
Stoddart will not arrange a warranty call out until it receives the above information from you in writing.
d) Upon receipt of a properly completed Stoddart Warranty Request Form, Stoddart will check its records to confirm whether
the equipment is eligible for warranty repair. If warranty rep air is required, Stoddart will issue an OFFICIAL AUTHORISATI ON NUMBER and
details of work to be carried out by a Stoddart authorised service agent. This authorisation number MUST be obtained before any work is
carried out. Stoddart will not accept invoices f or work carried out without an official authorisation number or by an unauthorised service agent.
e) Customer must quote the official authorisation number on all correspondence and invoices relating to a warranty claim to
ensure prompt processing by Stoddart.
f) Customer must pay all cos ts as sociated with a call-out for work that is not related to warranty repairs or outside Stoddart's
Terms immediately.
5. Timing of Warranty Services
5.1 Stoddart will comply with its warranty liabilities contained in these Terms in a timely manner.
6. General Maintenance and Repairs
6.1 The equipment must be repaired and maintained by a qualified technician. Stoddart's authorised service agents are
experienced technicians who understand the equipment and carry commonly used spare parts. Contact Stoddart's national
service number listed below for details of your nearest Stoddart authorised service agent.
For Warranty, maintenance, spare parts and repairs, contact:
Tel: 1300 307 289 Fax: 07 3344 1000 email: [email protected]
Page 30
Page 31
WARRANTY REQUEST FORM
Phone: (07) 3440 7600 Int: +617 3440 7600
Phone: 1300 307 289
Fax: (07) 3344 1000 Int: +617 3344 1000
Email: [email protected]
To ensure we can provide the best possible service we require you to complete this form. Make, model and serial number, along with other essential
information. To secure a call, you must also have an account with Stoddart or complete the credit card details below.
THIS FORM MUST BE COMPLETED OR WARRANTY CANNOT BE PROCESSED
Name of contact person on site: Date: / /
Business/Organisation name:
Street Address:
Suburb: State: Post Code:
Phone (Site): Mob:
Equipment Type: Brand:
Model/PNC no.: Serial no.:
Location (large sites only): Open: Close:
Date of purchase:
Company purchased from:
(please provide a copy of your tax invoice or delivery docket as proof of purchase)
Description of fault:
Has the following been checked (tick box if appropriate and checked)?
Electrical power supply Gas Water Supply
Name of person requesting warranty (please print):
CREDIT CARD DETAILS – Required as security against chargeable work (see note below)
Card type:
Visa
Mastercard
Cardholder name: Card no.:
Signature: Expiry Date:
PLEASE NOTE: Warranty call-outs take place Mondays to Fridays between 8.00 and 16.30 (except public holidays). Any calls outside these
times will be subject to penalty rates. Certain items such as glass components and light fittings are not covered under warranty. Claims for noncovered parts, no faults found, travel over 50km or other items outside our standard terms and conditions will be chargeable. Any chargeable
items will be COD terms – payable onsite.
CREDIT CARD INFORMATION MUST BE PROVIDED AS SECURITY AGAINST FALSE WARRANTY CALL-OUTS. FAILURE TO DO SO
WILL RESULT IN REQUEST BEING UNATTENDED. NORMAL BUSINESS HOURS ARE 8AM – 4.30PM MONDAY TO FRIDAY
Loading...