Woods Equipment MAN0680, BB6000X, BB7200X, BB8400X User Manual

BRUSHBULL

ROTARY CUTTER

BB6000X BB7200X BB8400X

MAN0680

(Rev. 4/24/2009)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner.

The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to return the prepaid postage portion to Woods, give one copy to the customer, and retain one copy. Failure to register the product does not diminish

customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided:

dealer. Read manual instructions

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety.

2 Introduction

Gen’l (Rev. 2/19/2008)

TABLE OF CONTENTS

Si no lee Ingles, pida ayuda a

alguien que si lo lea para que le

traduzca las medidas de seguridad.

LEA EL INSTRUCTIVO!

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY VIDEO ORDER FORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 46

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

MAN0680 (11/30/2007)

Introduction 3

SPECIFICATIONS

WARNING

Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2" - 12"

Blade Spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Number of Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat Treated Alloy Steel

Blade Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CCW

Tractor PTO rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540

Universal Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Category 5

Cutter Frame Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"

Tailwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5" x 16"

Specification BB6000X BB7200X BB8400X

Cutting Width 60" 72" 84"

Overall Width 67.5" 79.5" 91.5"

Weight (Approximate lbs.) 1300 lbs 1500 lbs 1790 lbs

Blade Speed (Feet per minute) 13,575 13,950 14,250

Gearbox 1:1.6 1:1.37 1:1.2

Recommended Maximum Tractor HP 40 - 150 50 - 150 65 - 150

3-Point Hitch I - II I - II II - III

GENERAL INFORMATION

 Some illustrations in this manual show the equipment with safety shields removed to provide a better view. This equipment should never be operated with any necessary safety shielding removed.

The purpose of this manual is to assist you in operating and maintaining your cutter. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying

4 Introduction

operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation.

The illustrations and data used in this manual were current at the time of printing but, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification.

Throughout this manual, references are made to right and left directions. These are determined by standing behind the equipment facing the direction of forward travel. Blade rotation is counterclockwise as viewed from the top of the cutter.

MAN0680 (11/30/2007)

Free Mower Safety Video

Fill out and return the order form and we will send you a FREE VHS or DVD video outlining

Industrial and Agricultural Mower Safety

Practices

. The 22 minute video, developed in cooperation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures to follow while operating your mowing equipment. The video does not replace the information contained in the Operator’s Manual, so please review this manual thoroughly before operating your new mowing equipment.

Safety Training Does Make a Difference.

BE SAFE!

BE ALERT!

BE ALIVE!

BE TRAINED Before Operating Mowers!

ASSOCIATION OF EQUIPMENT MANUFACTURERS

Safety Video Order Form

Safety Video Order Form (8/2/2005)

Safety 5

Also, available from the Association of Equipment Manufacturers:

A large variety of training materials (ideal for groups) are available for a nominal charge from AEM. Following is a partial list:

● Training Package for Rotary Mowers/Cutters-English

Contains: DVD & VHS (English)

Guidebook for Rotary Mowers/Cutters (English) AEM Industrial/Agricultural Mower Safety Manual (English) AEM Agricultural Tractor Safety Manual (English)

● Training Package for Rotary Mowers/Cutters-English/Spanish

Contains: DVD & VHS (English/Spanish)

Guidebook for Rotary Mowers/Cutters (English/Spanish) AEM Industrial/Agricultural Mower Safety Manual (English/Spanish) AEM Agricultural Tractor Safety Manual (English/Spanish)

AEM training packages are available through:

AEM at:

or Universal Lithographers, Inc. Email: aem@ulilitho.com

800-369-2310 tel 866-541-1668 fax

www.aem.org



Free Mower/ Cutter Safety Video Order Form

3 (Select one)

VHS Format - VHS01052 Safety Video

Please send me

Name: ________________________________________ Phone: __________________

Address: _____________________________________

_____________________________________

Mower/Cutter Model: ______________________ Serial #: ________________________

Send to: ATTENTION: DEALER SERVICES

WOODS EQUIPMENT COMPANY

PO BOX 1000 OREGON IL 61061-1000 USA



DVD Format - DVD01052 Safety Video



6 Safety

Safety Video Order Form (Rev. 2/6/2006)

TRAINING

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.

It has been said, “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

 Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules can result in serious injury or death.

 If you do not understand any part of this manual and need assistance, see your dealer.

 Know your controls and how to stop engine and attachment quickly in an emergency.

 Make sure attachment is properly secured, adjusted, and in good operating condition.

 Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

 Make sure driveline guard tether chains are attached to the tractor and equipment as shown in the pamphlet that accompanies the driveline. Replace if damaged or broken. Check that driveline guards rotate freely on driveline before putting equipment into service.

 Before starting the power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting equipment into service.

 Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

 Inspect chain, rubber, or steel band shielding before each use. Replace if damaged.

 Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.

 Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)



Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions.

 Never allow children or untrained persons to operate equipment.

PREPARATION

 Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

 Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Single Spindle HD (Rev. 9/15/2006)



Make sure shields and guards are properly

installed and in good condition. Replace if damaged.

 Do not put this equipment into service unless all side skids are properly installed and in good condition. Replace if damaged.

 A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

 Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

(Safety Rules continued on next page)

Safety 7

(Safety Rules continued from previous page)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

OPERATION

 Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

• If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

• This shielding is designed to reduce the risk of thrown objects. The mower deck and protective devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. and escape, traveling as much as 300 feet (92 m).

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

 Never direct discharge toward people, animals, or property.

 Do not operate or transport equipment while under the influence of alcohol or drugs.

 Operate only in daylight or good artificial light.

 Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all moving parts.

 Always comply with all state and local lighting and marking requirements.

 Never allow riders on power unit or attachment.

 Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

 Always sit in power unit seat when operating controls or starting engine. Securely fasten seat

It is possible for objects to ricochet

belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

 Operate tractor PTO at 540 RPM (1000 RPM on Q Series cutters). Do not exceed.

 Look down and to the rear and make sure area is clear before operating in reverse.

 Do not operate or transport on steep slopes.

 Do not stop, start, or change directions sud-

denly on slopes.

 Use extreme care and reduce ground speed on slopes and rough terrain.

 Watch for hidden hazards on the terrain during operation.

 Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

 Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

TRANSPORTATION

 Always comply with all state and local lighting and marking requirements.

 Never allow riders on power unit or attachment.

 Do not operate PTO during transport.

 Watch for hidden hazards on the terrain.

 A minimum 20% of tractor and equipment

weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

 Do not operate or transport on steep slopes.

 Do not operate or transport equipment while

under the influence of alcohol or drugs.

MAINTENANCE

 Before dismounting power unit or performing any service or maintenance, follow these steps:

8 Safety

Single Spindle HD (Rev. 9/15/2006)



SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt.

 Before performing any service or maintenance, disconnect driveline from tractor PTO.

 Before working underneath, disconnect driveline, raise cutter, lock in transport position, and block cutter securely. Hydraulic system leak down and failure of mechanical or hydraulic system can cause equipment to drop.

 Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way.

 Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous.

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Make sure attachment is properly secured, adjusted, and in good operating condition.

 Keep all persons away from operator control area while performing adjustments, service, or maintenance.

 Make certain all movement of equipment components has stopped before approaching for service.

 Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

 Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

 Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

 Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

 Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)



Make sure shields and guards are properly

installed and in good condition. Replace if damaged.

 Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers.

 Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

STORAGE

 Disconnect cutter driveshaft and secure up off ground. Raise cutter with 3-point hitch. Place blocks under cutter side skids. Lower cutter onto blocks. Disconnect cutter from tractor 3-point hitch and carefully drive tractor away from cutter.

 Keep children and bystanders away from storage area.

Single Spindle HD (Rev. 9/15/2006)

Safety 9

1 - SERIAL NUMBER PLATE

12 - PN 57123 RED REFLECTOR 9"

ROTATING BLADES AND

THROWN OBJECTS

 Do not put hands or feet under or into mower when engine is

running.

 Before mowing, clear area of objects that may be thrown by

blade.

 Keep bystanders away.

 Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE

SERIOUS INJURY OR DEATH.

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

 All driveline guards, tractor and

equipment shields in place

 Drivelines securely attached at both

ends

 Driveline guards that turn freely on

driveline

1006682-A

DANGER

8 - PN1006682

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer, or in the United States and Canada call 1-800-319-6637.

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

MODEL NO. SER IAL NO.

Woods Equipment Company

Oregon, Illinois, U.S.A.

10 Safety

MAN0680 (11/30/2007)

10 - PN 33347

GUARD MISSING.

DO NOT OPERATE.

DANGER

33347E

DANGER

GUARD MISSING.

DO NOT OPERATE.

14 - PN 1004114

CRUSHING AND PINCHING HAZARD

 Be extremely careful handling various parts of the machine.

They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement.

 Operate tractor controls from tractor seat only.

 Do not stand between tractor and implement when tractor

is in gear.

 Make sure parking brake is engaged before going between

tractor and implement.

 Stand clear of machine while in operation or when it is

being raised or lowered.

WARNING

TO AVOID SERIOUS INJURY OR DEATH:

 Read Operator's Manual (available from dealer) and follow

all safety precautions.

 Keep all shields in place and in good condition.

 Operate mower from tractor seat only.

 Lower mower, stop engine and remove key before

dismounting tractor.

 Allow no children or untrained persons to operate

equipment.

 Do not transport towed or semi-mounted units over 20 mph.

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

 Tractor must be equipped with ROPS (or ROPS CAB) and

seat belt. Keep foldable ROPS systems in "locked up" position at all times.

 Buckle Up! Keep seat belt securely fastened.

 Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

 Before working underneath, follow all instructions and

safety rules in operator's manual and securely block up all corners of equipment with jack stands.

 Securely blocking prevents equipment from dropping from

hydraulic leakdown, hydraulic system failures or mechanical component failures.

1006681

WARNING

DO NOT EXCEED PTO SPEED OF

540 RPM

PTO speeds higher than 540 RPM can cause

equipment failure and personal injury.

3 - PN1006681

11 - PN18864

CONTACT WITH ROTATING PARTS

CAN CAUSE SERIOUS INJURY.

WARNING

15502--B

ROTATING COMPONENTS

Do not operate without cover in place. Look and listen for rotation. Do not

open cover until all components have stopped.

5 - PN 15502

If shaft connection is visible, shield is missing. Replace shield before operating equipment.

DANGNGERER

1004114

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

 All driveline guards, tractor and

equipment shields in place

 Drivelines securely attached at both ends

 Driveline guards that turn freely on

driveline

18864-C

MAN0680 (11/30/2007)

Safety 11

OPERATION

DANGER

WARNING

CAUTION

WARNING

The operator is responsible for the safe operation of the cutter. The operator must be properly trained. Operators should be familiar with the cutter, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 7 to page

11. Be sure to complete the Pre-Operation Check List on page 16 before operating this cutter.

This heavy-duty cutter is designed for grass and weed mowing and shredding.

Recommended mowing speed for most conditions is from 2 to 5 mph.

 Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

• If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

It is possible for objects to ricochet

TRACTOR STABILITY

Figure 1. Tractor Stability

CONNECTING CUTTER TO TRACTOR

 Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

 Never allow riders on power unit or attachment.

 Make sure spring-activated locking pin or collar

slides freely and is seated firmly in tractor PTO spline groove.

 Operate tractor PTO at 540 RPM. Do not exceed.

 Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servicing equipment.

 Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

■ Make sure driveline will not bottom out at the

shortest length and that it has at least 1/3 overlap at the longest length.

■ With cutter adjusted to transport position, set

upper stop on tractor lift quadrant to prevent cutter from contacting the driveline when being raised.

1. Attach tractor 3-point lift arms to category I or

category II (Cat II or Cat III for BB8400X) side of hitch pins (5) and secure.

2. Attach tractor top link (1) to cutter top link attachment point (2). See Figure 2.

3. Raise cutter to transport position and adjust tractor top link until cutter is level in this position.

4. Adjust the tractor lower 3-point arm anti-sway devices to prevent cutter from swinging side to side during transport.

5. Adjust tractor drawbar so that it will not interfere with cutter or driveline.

12 Operation

MAN0680 (11/30/2007)

Figure 2. Cutter to Tractor Connection

1. Tractor top link

2. Cutter top link attachment point

5. Hitch pin

BB6000X, BB7200X

BB8400X

CAT II Position

CAT I Position

CAT II Position

CAT III Position

QUICK HITCH SET-UP

Refer to Figure 3 and Figure 4.

Figure 4. Mounting Pin Installation

DRIVELINE ADJUSTMENT

Category I and II for BB6000X, BB7200X

1. CAT I: No adjustment is required.

2. CAT II: Remove hardware securing lift arms to

mounting lugs. Move lift arms forward to second holes and insert caps screws. Tighten hardware.

3. Install mounting pins as shown in Figure 4 for correct hitch configuration.

Category II and III for BB8400X

1. CAT II: No adjustment is required.

2. CAT III: Remove hardware securing lift arms to

mounting lugs. Move lift arms forward to second holes and insert cap screws. Tighten hardware.

3. Install mounting pins as shown in Figure 4 for correct hitch configuration.

NOTICE

■ Avoid contact with driveline when raising cut-

ter.

■ Make sure driveline will not bottom out at the

shortest length and that it has at least 1/3 overlap at the longest length.

■ With cutter adjusted to transport position, set

upper stop on tractor lift quadrant to prevent cutter from contacting the driveline when being raised.

Attach the cutter to the tractor 3-point hitch (or quick hitch if available). Do not attach driveline. Raise and lower cutter to determine maximum and minimum distance between the tractor PTO shaft and the gearbox input shaft. If the distance is too large, the driveline will be too short for proper engagement. If distance is too small, the driveline may bottom out in operation and damage the cutter or tractor.

The driveline length must be sufficient to provide at least 1/3 driveline length of engagement during operation. There must be at least 4 inches of engagement at the cutter’s lowest possible point of operation. The driveline must not bottom out when raised to the maximum height possible.

Figure 3. Left Rail Mounting Lug

MAN0680 (11/30/2007)

If driveline is too short, please call your Woods dealer for a longer driveline.

If driveline is too long, please follow the instructions for shortening the driveline.

Operation 13

Shortening Driveline

DP2

1-9/16"

DP3

DP4

DP5

1. Move cutter up and down to get the shortest possible distance between tractor PTO shaft and gearbox input shaft.

2. Separate driveline into two halves and connect them to the tractor PTO and gearbox.

3. Place driveline halves parallel to one another to determine how much to shorten the driveline.

Figure 7. Cut Shield

6. Place the cutoff portion of the shield against the

end of the shaft and use as a guide. Mark and cut the shaft.

Figure 5. Drive Halves Placed Parallel

4. Measure from end of the upper shield to the base

of the bell on the lower shield (A). Add 1-9/16" to dimension (A). See Figure 6.

Figure 6. Determine Shield Length

5. Cut the shield to the overall dimension.

Figure 8. Cut Shaft to Length

7. Repeat step 6 for the other half of the drive.

8. File and clean cut ends of both drive halves.

Do not use tractor if proper driveline engagement cannot be obtained through these methods.

Connect driveline to tractor PTO shaft, making sure the spring-activated locking collar slides freely and locks driveline to PTO shaft.

NOTICE

■ If attaching with quick hitch, the distance

between the tractor PTO and gearbox input shaft will increase. Please follow the steps as you would for a 3-point hitch to insure proper engagement.

14 Operation

MAN0680 (11/30/2007)

DRIVELINE INTERFERENCE CHECK

WARNING

3" Desired cutting height

+ 11.5" Distance blade cutting edge is below deck

= 14.5"

2. Check chain bracket

3. Check chain

1. Check for clearance between driveline and cutter deck.

2. Slowly lift cutter and observe driveline. If clearance between driveline and cutter deck is less than 1 inch, shorten top link or limit upper travel of lower hitch arms. Refer to tractor operator's manual for instructions.

CUTTING HEIGHT ADJUSTMENT

 Keep all persons away from operator control area while performing adjustments, service, or maintenance.

■ Avoid low cutting heights. Striking the ground

with blades produces one of the most damaging shock loads a cutter can encounter. Allowing blades to contact ground repeatedly will cause damage to cutter and drive.

c) Adjust the front-to-rear attitude from 1/2" to

3/4" higher than the front.

CHECK CHAIN ADJUSTMENT

1. Refer to Check Chain Installation (Optional), page

33 for check chain installation.

2. After making cutting height adjustment, adjust both chains (3) in check chain bracket (2) so you have the same number of links on each side. This will keep your cutting level.

When selecting a cutting height, you should consider the area of operation. If the ground is rolling and has mounds the blades could contact, set the cutting height accordingly.

1. Level cutter from side to side. Check by measuring from cutter frame to the ground at each deck rail.

2. Adjust, using tractor 3-point arm leveling device.

NOTE: Keep the front of cutter level with or slightly

lower than rear for best mowing.

3. Control cutting height with tractor 3-point arms, rear tailwheel adjustment, or optional check chains.

4. To raise rear of cutter, move tailwheel down.

5. To raise front of cutter, raise tractor 3-point arms or

shorten optional check chains.

The cutting height is the distance between the blade and the ground. The blades are approximately 11.5" below the deck. To check cutting height, do the following:

a) Place a straight edge along top edge of deck.

b) Select a cutting height; as an example, for an

approximate cutting height of 3", set the center of the deck 14.5" above the ground:

Figure 9. Check Chain Adjustment

DRIVELINE INSTALLATION (TRACTOR PTO)

To Install:

Pull locking collar back and at the same time push driveline onto tractor PTO shaft until locking device engages.

To Remo v e:

Hold driveline into position, pull locking collar back, and slide driveline off tractor PTO shaft.

Figure 10. Lock Collar

MAN0680 (11/30/2007)

Operation 15

+ 35 hidden pages