Woodhaven 966 User Manual

Parts List:

Please identify and verify that you have all of the

hardware shown below prior to assembly.

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

966A Clamp Fence . . . . . . . . . . . . . . . . . . . . . . 1

966B 15-3/4” sq. MDF Base . . . . . . . . . . . . . . 1

966C Fence Bracket . . . . . . . . . . . . . . . . . . . . . 2

4006 6” Double Track Fence . . . . . . . . . . . . . 3

6305 500 lb. Toggle Clamp . . . . . . . . . . . . . . 1

966

Biscuit Master

Owners Manual

Please Read Carefully!

Part# Description Qty.

MP375 3/8” Screw 1

Part# Description Qty.

BUSH1250 1/4” Spacer 4

Part# Description Qty.

MP200 2” Screw 2

Part# Description Qty.

5772B 1” Screw 2

Part# Description Qty.

MF020 1-1/4” Screw 4

Part# Description Qty.

NUT025 3/4” Sq. Nut 4

Part# Description Qty.

MF015 1” Screw 2

Part# Description Qty.

5760B Oval Nut 8

Part# Description Qty.

5525 Nylon Knob 1

Part# Description Qty.

WB002 Washer 4

Part# Description Qty.

5863 Ratchet Handle 4

Part# Description Qty.

6305B Clamp Pad 1

BEFORE BEGINNING

Identify and verify that you have
all the parts listed. Read the instructions
at least once, familiarizing yourself with
the parts before beginning. You'll need
a #3 Phillips screwdriver for assembly.

1

1-2. BASE ASSEMBLY

Insert the 1-1/4" screws
(MF020) thru the countersunk
holes in the MDF Base (966B) and
start an oval nut (5760B) on the
end of each screw. See fig. 1.
Slide the Fence Brackets (966C) on
to the oval nuts so they’re approximately
centered them. Install a washer (WB002)
on both 2" screws (MP200). Starting
from the smooth edge of the Fence
Bracket, insert a 2" screw thru the hole
in each bracket and start an oval nut
(5760B) on the end of each screw. Slide
a 6" Double Track Fence (4006) on the
oval nut. Position the Fence even with
the inside ends of each Fence Bracket
and tighten the screw. See fig. 1.

Clamp the MDF Base to a bench
so the 1-1/4" screws overhang the
edge of the bench and you can tighten
them from the underside. Mark a
center line on the MDF Base in line
with its center slot. See fig. 2 inset.
Place your biscuit machine between
the Fence/Fence Brackets, centered
on the line you just made. Slide the
Fence/Fence Brackets against each side
of the biscuit machine. Don’t force the
Fence/Fence Brackets too tight against
the sides of the biscuit machine as their
only purpose is to prevent major side­to-side play. In fact a little play (1/32" or
less) is preferable for easier removal of
the biscuit machine. It’s not necessary that
the Fence/Fence Brackets conform to the
shape of your biscuit machines sides. Use a
straight edge to align the Fences with each
other and tighten the four 1-1/4" screws
from the underside of the MDF Base.

4006

966C

4006

966C

2

Some biscuit machines have
mounting holes in their base and, if
desired, you can fasten your biscuit
machine directly to the MDF Base.

1