Woodhaven 8680, 8695 User Manual

Parts List:

You will receive ONE of the Marking Plates below with the

8680 or 8690 and BOTH Marking Plates with the 8695:

Part Description Quantity

8680B Inch Marking Plate . . . . . . . . . . . . . . . . 1

8690B Metric Marking Plate . . . . . . . . . . . . . . 1

8680A 1/2" Cap . . . . . . . . . . . . . . . . . . . . . . . . . . 1

8680C 1/4" Cap . . . . . . . . . . . . . . . . . . . . . . . . . . 1

8610D Indexing Plate . . . . . . . . . . . . . . . . . . . . . 1

8610E Indexing Plate Riser . . . . . . . . . . . . . . . 1

4208 7-7/8" One Track . . . . . . . . . . . . . . . . . . 1

4216 15-7/8" One Track . . . . . . . . . . . . . . . . . 1

Plus the parts listed below:

8680, 8690 & 8695 Hdw. Marking Jigs

Please Read Carefully!

Part# Description Qty.

5771B 3/4" Screw 2

Part# Description Qty.

MP150 1-1/2" Screw 2

Part# Description Qty.

BUSH001 1/8" Spacer 3

Part# Description Qty.

BUSH050 3/8" Spacer 5

Part# Description Qty.

MF035 1/2" Screw 2

Part# Description Qty.

5521 Thumb Nut 2

Part# Description Qty.

MP200 2" Screw 1

Part# Description Qty.

BUSH004 5/8" Spacer 2

Part# Description Qty.

HB030 1" Bolt 1

Part# Description Qty.

HB050 1-1/2" Bolt 1

Part# Description Qty.

5860 Ratchet Handle 1

Part# Description Qty.

WB002 Washer 1

Part# Description Qty.

BUSH5050 1/2" Spacer 1

Part# Description Qty.

5863 Ratchet Hand. w/stud 1

Part# Description Qty.

5760B Oval Nut 2

BEFORE BEGINNING

Identify and verify that you have all the parts listed.

Read the instructions at least once before beginning.

ASSEMBLY

Attach the 1/4" Cap (8680C) to the 1/2" Cap (8680A) using the 3/4" screws (5771B). See fig. 1.

Install a 1/8" Spacer (BUSH001) and then a 3/8" Spacer

(BUSH050) on both of the 1-1/2" Screws (MP150). Insert

the screws thru the two open holes in the Caps and start an Oval Nut (5760B) on the end of each screw. See fig. 2. Lay the assembly on edge. Slide the 7-7/8" One Track

(4208, used for doors) or 15-7/8" One Track (4216, used for drawers) on the oval nuts until it's flush with one end of

the assembly, then tighten the 1-1/2" screws. See fig. 2. Slide the Marking Plate (8680B or 8690B) in the slot of the assembly with the shallow black cross-hairs in the Plate facing the 1/4" Cap. The slot in the Marking Plate should be lined up with the tapped hole in the 1/2" Cap below it. Install a 1/2" Bushing (BUSH5050) and a washer (WB002) on a Ratchet Handle w/stud (5863). Install the Ratchet Handle w/stud thru the slot in the Marking Plate and start it in the tapped hole in the 1/2" Cap. See fig. 3.

Attach the Indexing Plate (8610D) to the Indexing Plate

Riser (8610E) using the 1/2" screws (MF035). See fig. 4.

Insert a 1" bolt (HB030) thru the assembly, install a 1/8" Spacer (BUSH001) and start a Ratchet Handle (5860) on the end of the bolt. Slide the assembly on the One Track and tighten. Install a 5/8" Bushing (BUSH004) on the 2" Screw (MP200), insert the screw thru the hole in the Indexing Plate, install another 5/8" Bushing and then the Thumb Nut (5521). See fig. 5.

+ 2 hidden pages