Woodhaven 7285 User Manual

Parts List:

Please identify and verify that you have all of the

hardware shown below prior to assembly.

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

7285B Supports, 3 pc. set . . . . . . . . . . . . . . . . . 1

7285D Circle Jig Base . . . . . . . . . . . . . . . . . . . . . 1

7285E 15-5/8” One Track . . . . . . . . . . . . . . . . . 1

4012 12” Double Track . . . . . . . . . . . . . . . . . . 1

4959C Miter Lock . . . . . . . . . . . . . . . . . . . . . . . . 1

7285

Band Saw Circle Jig

Owners Manual

Please Read Carefully!

Part# Description Qty.

SFP011 7/16” Screw 2

Part# Description Qty.

BUSH050 3/8” Spacer 1

Part# Description Qty.

5784 1/8” Wrench 1

Part# Description Qty.

NUT015 1/4-20 Nut 1

Part# Description Qty.

MF015 1” Screw 1

Part# Description Qty.

MA003 1/4” Set Screw 1

Part# Description Qty.

MF010 3/4” Screw 9

Part# Description Qty.

5760B Oval Nut 8

Part# Description Qty.

WN003 Nylon Washer 1

Part# Description Qty.

7285C Circle Pin 1

BEFORE BEGINNING

Identify and verify that you have all the parts listed. Read
the instructions at least once, familiarizing yourself with the
parts before beginning. The Band Saw Circle Jig was designed
for use with the Woodhaven 7280 Band Saw Fence ONLY.
You'll need a #2 & #3 Phillips screwdriver for assembly.

ASSEMBLY

Get the set of supports (7280B - 3 pc. set). Two of the three
parts are the same length and the third one is shorter. Install a
3/4" screw (MF010) in the center countersunk hole of the short
piece and tighten. This screw will be the pivot screw for the
Circle Jig Base. In the remaining holes in all three parts, install
the 3/4" screws (MF010) thru the countersunk holes and start
an oval nut (5760B) on the end of each screw. See fig. 1.
Remove the Ultra Track fence and guides from the 24"
Double Tracks of the Woodhaven Band Saw Fence. Loosen and
slide the 24" Double Tracks to the right on the brackets as far
as they will go and retighten the knobs. Measure the outside­to-outside distance of the two 24" Double Tracks. See fig. 2.
Install the three support pieces (7285B - 3 pc. set)
on the 12" Double Track (4012). Adjust the spacing of the
supports so they match the outside-to-outside distance of the
24" tracks. Center the 12" track on the two long supports and
tighten the screws holding them to the 12" track. See fig. 3.
Slide the assembly onto the ends of the 24" tracks until
the oval nuts at each end are in the 24" tracks, then loosely
tighten the screws. Measure the distance from the front 24"
track to the front of the band saw blade. Adjust the short
support piece on the 12" track so the center of the pivot screw
is the same distance from the front 24" track and tighten
the two screws holding it on the 12" track. See fig. 4.
Adjust the position of the support assembly
until the distance between the blade and pivot screw
measures 14-3/4" and tighten the two screws that attach
the support assembly to the 24" tracks. See fig. 4

1

2

3

4

1