Woodhaven 6015, 578DRO User Manual
Parts List:
Part Description Quantity
6015 Digital Readout unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6015A DRO Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6015B Bracket Mount w/hdw., bagged. . . . . . . . . . . . . . . . . . . 1
BUSH002 5/8" OD x 1/4" long spacer . . . . . . . . . . . . . . . . . . . . . . . 3
BUSH004 5/8" OD x 5/8" long spacer. . . . . . . . . . . . . . . . . . . . . . . 2
5521 knob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
HB030 1" bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MF031 1/4-20 x 2-1/4" flathead screw. . . . . . . . . . . . . . . . . . . . 1
Parts below are used for 578DRO only:
NUT010A locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
WB002 washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
HB059 1/4-20 x 2-1/2" bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
BEFORE BEGINNING
Identify and verify that you have all the parts listed.
Read thru the instructions at least once, familiarizing yourself
with the parts and process before proceeding. You'll need a #3
Phillips screwdriver for assembly to our 6000-6004 Horizontal
Router Table. Note: You can't use the digital readout if you
have an Angle-Ease model setup with the bit tilting down.
6015 & 578DRO
Digital Readout
Please Read Carefully!
1
2
578P 576P
1/4" hole 5/16"
down from the
top and 1-1/16"
in from an edge.
IF YOU HAVE A 576-578
You'll need two 7/16" wrenches for assembly, plus a
1/4" drill. As you face the front of the Horizontal Router
Table/Plate, drill 1/4" hole in the upper left (or right - see
below) hand corner of the plate 5/16" down from the top
and 1-1/16" in from the edge of the plate. See fig. 2.
ASSEMBLY
Get the Digital Readout (6015) and read thru the
iGAGING DigiMAG Remote Readout instructions to
familiarize yourself with its parts list. The Slider Sensor Unit
(3) comes pre-installed on the Digital Scale Beam (4) which
has two holes drilled in it. The Connection Cable (2) of the
Slider Sensor Unit should be sticking out towards the back
of the Horizontal Router Table when assembly is complete.
Install a 1/4" spacer (BUSH002) on both of the 1" bolts
(HB030). From the back of the Digital Scale Beam, insert the
bolts thru the holes at each end and screw a knob (5521) on the
end of each bolt. Slide the heads of the bolts into the T-slot of
one of the 24" Double Tracks on your Horizontal Router Table,
keeping the 1/4" spacer between the Double Track and the back
of the Digital Scale Beam. Position the beam where desired
on the track for now and tighten the knobs. See fig. 3 & 4.
3
(4)
(2)
(3)
ATTACH 6015A TO ROUTER PLATE
Attach the DRO Mount (6015A) to back of the router plate
of your Horizontal Router Table, following one of the next two
instructions that cover your Horizontal Router Table model.
4
INSTALL 6015A ON THE 6000-6004
Insert the 2-1/4" flathead screw (MF031) thru the
countersunk hole in the DRO Mount (6015A) and install one
1/4" spacer (BUSH002) and two 5/8" spacers (BUSH004)
on it. Press the "ears" of the DRO Mount over the body of
the Slide Sensor Unit and, from the back of the router plate,
fasten the screw/spacers/DRO Mount to the threaded hole in
the upper right or left hand corner of the plate. See fig. 5.
INSTALL 6015A ON THE 576-578
Install a washer (WB002) on the 2-1/2" bolt (HB059),
insert it thru the countersunk hole in the DRO Mount (6015A)
and install one 1/4" spacer (BUSH002) and two 5/8" spacers
(BUSH004) on it. Press the "ears" of the DRO Mount over
the body of the Slide Sensor Unit and, from the back of the
router plate, fasten the bolt/spacers/DRO Mount to the hole you
drilled in the upper corner of the router plate, using a second
washer and a locknut (NUT010A) to fasten it to the plate.
MOUNT THE DIGITAL DISPLAY UNIT
The Digital Display Unit (1) can be mounted on any
magnetic surface using the magnets in the back of it. We also
supply a Bracket Mount (6015B) that has the Stand Base for
Display Unit (8), plus other hardware, pre-attached to it. Install
a 3/8" spacer (BUSH5038) on the thumb screw (5500), insert
the thumb screw thru the hole in the angle bracket attached to
the Bracket Mount and start an oval nut (5750B) on the end of
it. Slid the oval nut into the T-slot on the side or front of the
24" Double Track and tighten the thumb screw. See fig. 6.
5
Ears of DRO
Mount (6015A)
press fi t ove r
body of Slide
Sensor Unit.
Scale
Beam
HB030
BUSH0025521
Track
6015A
MF031
USING THE DIGITAL READOUT
You will have extra hardware left over (5, 6, 7 & 9) from
the iGAGING parts list. This is the manufacturers mounting
hardware that we don't use. Follow the iGAGING instructions
regarding the Display Functions. Install the batteries in the back
of the Digital Display Unit (10 - rear view) to begin using it.
Loosen and slide the Digital Scale Beam to any position
along the length of the Double Track to take advantage
of the full adjustment range of the Horizontal Router
Table. Make sure the knobs are tightened before making
any height adjustments or the reading will be faulty.
©Copyright WOODHAVEN INC. 11/10/10
(800) 344-6657 or www.woodhaven.com
6
6015B
5500, BUSH5038
& 5750b
(8)
(8)
Loading...