Woodhaven 6010 User Manual

Parts List:

Please identify and verify that you have all of the

hardware shown in the drawings and the parts listed

below prior to assembly.

Part Description Quantity

6010 HD Mortise Table assembly . . . . . . . . . 1

6010H1 Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

6010H2 Handle w/bracket . . . . . . . . . . . . . . . . . 1

6010T 15-3/4” x 15-3/4” Phenolic Table . . . . 1

6010C Table Fence . . . . . . . . . . . . . . . . . . . . . . . 1

4416 16" Ultra Track . . . . . . . . . . . . . . . . . . . . 1

6305IC Inboard Toggle Clamp . . . . . . . . . . . . . 2

6010

HD Mortise Table

Owners Manual

Please Read Carefully!

Part# Description Qty.

5860 Ratchet Handle 5

Part# Description Qty.

5760B Oval Nut 7

Part# Description Qty.

MF010 3/4" Screw 8

Part# Description Qty.

WN001 Nylon washer 9

Part# Description Qty.

BUSH004 5/8” Spacer 3

Part# Description Qty.

WB002 Washer 13

Part# Description Qty.

MF006 5/8” Screw 5

Part# Description Qty.

5765B Oval Nut 4

Part# Description Qty.

HB030 1" Bolt 5

Part# Description Qty.

NUT010A Locknut 3

Part# Description Qty.

5776B 1-1/4” Screw 3

BEFORE BEGINNING

Identify and verify that you have all the parts
listed. Read the instructions at least once, familiarizing
yourself with the parts, before beginning. You’ll need a #3
Phillips screwdriver and a 7/16" wrench for assembly.

ATTACH HANDLES TO HD MORTISE TABLE

Attach the Handle w/bracket (6010H2) to the location
shown on the HD Mortise Table assembly (6010HD).
Insert a 5/8" screw (MF006) thru the two countersunk
holes in the handle bracket and start an oval nut (5760B

- flat side first) on the end of the screws. See fig. 1.

Slide the two oval nuts into the T-slots of the Ultra

Track where indicated, adjust the bracket so it’s flush with the
end & edge of the track and tighten the screws. See fig. 1.
Attach the handles (6010H1 & 6010H2) at the three
locations indicated on the two brackets. You’ll need a 1-1/4"
screw (5776B) two brass washers (WB002), three nylon washers
(WN001) and a locknut (NUT010A) for each attachment point.
Later on after you’ve completed mounting the HD Mortise
Table to your Horizontal Router Table, adjust these screws/nuts
until you have the desired tension on the handles. See fig. 2 & 3.

1

2

5776B 1-1/4” screw

ATTACH STOPS TO TABLE

On three of the 1-1/4" bolts (HB030) install a 5/8" spacer
(BUSH004), a brass washer (WB002) and a ratchet handle
(5860). Slide the head of the bolts in the T-slots of the Ultra

Tracks where shown. The two front/lower stops control the
left-to-right movement of the table and the third upper/side
stop controls the forward movement of the table. See fig. 4.

4

WB002 brass washer

WN001 nylon washer

Bracket

WN001 nylon washer

Handle

WN001 nylon washer

WB002 brass washer

NUT010A locknut

3

Attach Handles to brack-

ets at these three locations.

1