Woodhaven 204 User Manual

Parts List:

Please identify and verify that you have all of the

parts listed and shown on this page prior to assembly.

Parts listed in this box are shown in photos in the

instructions.

Part Description Quantity

204A 48” Aluminum Fence . . . . . . . . . . . . . . 1

204B 24” Fence faces, pair . . . . . . . . . . . . . . . 1

200C Fence Base, set of 2 pcs. . . . . . . . . . . . . 1

200E End Blocks . . . . . . . . . . . . . . . . . . . . . . . . 2

200D Dust Port Blocks . . . . . . . . . . . . . . . . . .2

281 Dust Port . . . . . . . . . . . . . . . . . . . . . . . . . 1

200F Dust Port Plate . . . . . . . . . . . . . . . . . . . . 1

202G Guard Insert . . . . . . . . . . . . . . . . . . . . . . 1

3724RL Tapes, L & R . . . . . . . . . . . . . . . . . . . . . . . 1

224 Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

200FS Shims . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

200SC Fence Clamps for 202 & 203, pr. . . . . . 1

240 Hold-Down. . . . . . . . . . . . . . . . . . . . . . . . 1

242 Hold-In . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

204

Router Fence

Owners Manual

Please Read Carefully!

202 Router Fence
shown

Part# Description Qty.

5540 K nob 6

Part# Description Qty.

BUSH004 5/8” Spacer 4

Part# Description Qty.

BUSH002 1/4" Spacer 2

Part# Description Qty.

5793B Barrel Nut 8

Part# Description Qty.

MF010 3/4" Screw 6

Part# Description Qty.

5760B Oval Nut 5

Part# Description Qty.

5720 2-1/4" T-Bolt 6

Part# Description Qty.

MF006 5/8” Screw 4

Part# Description Qty.

5771B 3/4" Screw 2

Part# Description Qty.

5505 Thumb Screw 2

Part# Description Qty.

MF015 1” Screw 1

FENCE ASSEMBL Y

You'll need a #3 Phillips screwdriver for assembly.
Get the two pieces of the Fence Base (200C) and the two
End Blocks (200E). Assemble the Fence Bases and End
Blocks together using four 3/4" screws (MF010) and four
barrel nuts (5793B). Insert the screws through the counter­sunk holes in the fence base and start a barrel nut on the
end of each screw. Slide each End Block onto the two of
the barrel nuts and tighten the screws. See fig. 1, 2

Attach the Dust Port Blocks (200D) to the base assembly

using two 3/4" screws (MF010) and two barrel nuts (5793B).
Insert the screws through the counter-sunk holes and start a
barrel nut on the end of each screw. Slide a Dust Port Block
on to each barrel nut and tighten the screws. See fig. 3

Attach the Dust Port & Dust Port Plate (281 & 200F)
to the Dust Port Blocks using two 3/4" screws (5771B)
and two barrel nuts (5793B). Insert the screws through the
mounting holes in the Dust Port Plate and start a barrel
nut to the end of each screw. Insert the Dust Port into
the opening of the Dust Port Plate (no need to glue it in
place), insert the barrel nuts in the corresponding holes in
the Dust Port Blocks and tighten the screws. See fig. 3

1

2

Insert four 5/8" screws (MF006) through the fence base
and start an oval nut (5760B) on the end of each screw. Slide
the Aluminum Fence (204A) on to the oval nuts until the bit
opening in the Aluminum Fence aligns with the corresponding
opening in the fence base, then tighten the screws. See fig. 4

34

1