Woodhaven 1472 User Manual

1470 & 1472 Angle-Ease

™

6002 & 6004 Angle-Ease

Owners Manual

U.S. Patent #6,742,558

Please Read Carefully!

Additional Parts List:

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

1470AS Side/Arm Assembly, pair . . . . . . . . . . . . . . . . 1

1470C 7-1/2” Double Track . . . . . . . . . . . . . . . . . . . . . 2

1475 Height Adjuster (in it’s own package) . . . . . 1

In addition, you will get ONE of the motor

blocks and plates below, depending on the

Angle-Ease model you purchased:

1470B 3.5” Motor Block . . . . . . . . . . . . . . . . . . . . . . . . 1

1472B 4.2” Motor Block. . . . . . . . . . . . . . . . . . . . . . . . 1

1470P Angle Ease Router Table Plate . . . . . . . . . . . 1

6000PA Horizontal Table Angle-Ease Plate . . . . . . . . 1

The Angle-Ease ﬁ ts

motors from these routers:

FITS 3.5”

Router Model

Porter Cable 7518 No Yes

Milwaukee 5625 No W/ Shim

Porter Cable 892 Yes W/ Adapter R1

Porter Cable 690 Yes W/ Adapter R1

DeWalt 616/618 Yes W/ Adapter R1

Bosch 1617/1618 Yes W/ Adapter R1

Part# Description Qty.

WB002 Washer 4

ANGLE-

EASE

FITS 4.2”

ANGLE-

EASE

Part# Description Qty.

MF010 3/4" Screw 8

Part# Description Qty.

5760B Oval Nut 12

Part# Description Qty.

5791B Barrel Nut 3

Part# Description Qty.

MF015 1” Screw 6

Part# Description Qty.

BUSH002 1/4" Spacer 4

Part# Description Qty.

WN001 Nylon washer 4

Part# Description Qty.

Ringpin1 Pin 2

Part# Description Qty.

5863 Knob - 1-1/8” 2

Part# Description Qty.

5864 Knob - 1-5/8” 2

BEFORE BEGINNING

Identify and verify that you have all the parts listed. Read the instructions at least once, familiarizing yourself with the parts, before beginning assembly. You’ll need two 7/16" wrenches, a #3 Phillips screwdriver and a flat blade screwdriver.

ASSEMBLY Find the side/arm assembly (1470AS) that has the arm with the squared-off corner. Get the adjuster arm (1475A1) from the 1475 Height Adjuster package and attach it to the squared-off arm as shown, using two 3/4" screws (MF010). Pivot the arm as necessary to access the lower mounting hole in the arm. Set the remaining height adjuster parts and hardware aside until later. See fig. 1. Take both side/arm assemblies and align the pointer in the arm with the 10º mark on the scale on the top of the side. Insert a pin (Ringpin1) through the 10º hole in the side and into the hole in the arm. See fig. 2. Install a washer (WB002) and a nylon washer (WN001) on the stud of the knobs (5863). Slide another nylon washer (WN001) between the arm and side. A credit card can help position the washer. The washer must be aligned with the curved slot in the side and the threaded hole in the arm. Insert the stud of the knob thru the curved slot in the side, screwing it into the arm, then tighten the knob. See fig. 3. Insert 1" screws (MF015) thru the three countersunk holes in each side and start an oval nut (5760B - flat side first) on each screw. Slide a 7.5" deluxe track (1470C) on to the oval nuts on each Side. Center the deluxe track on the side, check the side for square on a flat surface and tighten the screws. See fig. 4. Remove the pin from each arm, loosen the handle and rotate the arm to the 0º mark on the side, then reinstall the pin and tighten the knob.

ATTACH ROUTER BLOCK

Set the router block on end with the clamping knob in the router block (1470B or 1472B) facing the bottom. Insert a barrel nut (5791B) in the hole in the face of the router block near the end. Use a flat blade screwdriver to align the threaded hole in the barrel nut with the cross hole in the router block. See fig. 5. Install a washer (WB002) and two 1/4" spacers

Pin removed for clarity

+ 2 hidden pages