Woodhaven 1461, 1463 User Manual

1461, 1462 & 1463

Angle-Ease

™

Owners Manual

U.S. Patent #6,742,558

Please Read Carefully!

Additional Parts List:

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

1460AS Side/Arm Assembly, pair . . . . . . . . . . . . . . . . 1

1460C 5-1/2” Double Track . . . . . . . . . . . . . . . . . . . . 2

1460P1 Angle Ease Router Plate . . . . . . . . . . . . . . . . . 1

1465 Height Adjuster (in it’s own package) . . . . . 1

In addition, you will get ONE of the motor blocks below,

depending on the Angle-Ease model you purchased:

1460B1 Porter Cable 310 Motor Block . . . . . . . . . . . . 1

1460B2 Ridgid Motor Block . . . . . . . . . . . . . . . . . . . . . 1

1460B3 Bosch Colt Motor Block . . . . . . . . . . . . . . . . . 1

Part# Description Qty.

WN001 Nylon washer 2

Part# Description Qty.

BUSH002 1/4" Spacer 2

Part# Description Qty.

MF010 3/4" Screw 10

Part# Description Qty.

5760B Oval Nut 8

Part# Description Qty.

5791B Barrel Nut 3

Part# Description Qty.

WB002 Washer 4

Part# Description Qty.

BUSH004 5/8" Spacer 4

Part# Description Qty.

5590 Knob 2

Part# Description Qty.

MF020 1-1/4” Screw 2

Part# Description Qty.

5864 Knob - 1-5/8” 2

Part# Description Qty.

Ringpin1 Pin 2

Part# Description Qty.

5863 Knob - 1-1/8” 2

BEFORE BEGINNING

Identify and verify that you have all the parts listed.
Read the instructions at least once, familiarizing yourself with
the parts, before beginning assembly. You’ll need two 7/16"
wrenches, a #3 Phillips screwdriver and a flat blade screwdriver.

ASSEMBLY
Find the side/arm assembly (1460AS, pair) that has
the arm with the squared-off corner. Get the adjuster arm
(1465A1) from the 1465 Height Adjuster package and
attach it to the squared-off arm as shown, using two 3/4"
screws (MF010). Pivot the arm as necessary to access the
lower mounting hole in the arm. Set the remaining height
adjuster parts and hardware aside until later. See fig. 1.
Take both side/arm assemblies and align the pointer
in the arm with the 30º mark on the scale on the top of
the side. Insert a pin (Ringpin1) through the 30º hole
in the side and into the hole in the arm. See fig. 2.
Install a washer (WB002) and a 1/4" spacer (BUSH002)
on the stud of the knobs (5863). Slide a nylon washer
(WN001) between the arm and side. A credit card can help
position the washer. The washer must be aligned with the
curved slot in the side and the threaded hole in the arm.
Insert the stud of the knob thru the curved slot in the side,
screwing it into the arm, then tighten the knob. See fig. 3.
Insert 3/4" screws (MF010) thru the two countersunk
holes in each side/arm assembly and start an oval nut
(5760B - flat side first) on each screw. Slide a 5.5" deluxe
track (1460C) on to the oval nuts on each side. Center
the deluxe track on the side, check the side for square
on a flat surface and tighten the screws. See fig. 4.
Remove the pin from each arm, loosen the
handle and rotate the arm to the 0º mark on the side,
then reinstall the pins and tighten the knobs.

ATTACH ROUTER BLOCK

Set the router block on end with the clamping knob
in the router block (1460B1, 1460B2 or 1460B3) facing
the bottom. Insert a barrel nut (5791B) in the hole in
the face of the router block near the end. Use a flat blade
screwdriver to align the threaded hole in the barrel nut
with the cross hole in the router block. See fig. 5.

1

2

3

Pin removed
for clarity

5

4

90° assembly

1