Wonders Technology DS1681 User Manual

SIZE：95 X 148NN

正反面印刷

Wireless Portable Bluetooth Speaker

Mode No.: DOSS SoundBox
User Manual

I. Introducon

Thank you for purchasing the DOSS SoundBox Wireless Portable Bluetooth
Speaker with Bluetooth and Hands free funcon. We encourage you to

read this instrucon guide thoroughly to get the most out of this innovave

wireless portable speaker.

II. Package content

• One wireless portable speaker

• USB charging cable

• Φ3.5mm auxiliary cable

• Travel waterproof pouch

• User manual,Warranty card,Contact card

III. Product overview

1

2

3

5

4

Backlit touch-sensive buons

1. Mode switch: Touch to toggle play mode among Bluetooth,
TF Card and Aux-in connecon.

2. In Bluetooth mode/TF mode, touch to skip backward.

3. Play/Pause and handset buon

• In Bluetooth mode,touch to answer or end a call. Touch for 3

seconds to reject a call.

• In Bluetooth mode, touch to play/pause your tune. Touch for 3

seconds to disconnect with your device.

• In TF mode, touch to play/pause your tune.

4. In Bluetooth mode/TF mode, touch to skip forward.

5. Volume control:

• Clockwise rotaon to increase the volume.

• Counterclockwise rotaon to decrease the volume.

6 7 8 9 10

6. Power buon: Long press to turn the device on and off.

7. Auxiliary Φ3.5mm jack : Use it for cabled playback with compable
devices.

8. TF card: Use it for TF card (with music) playback.

9. Charging port: Plug the supplied USB cable into this port to recharge

the built-in baery.

10. LED charging indicator.

• Charging : Steady Red.

• Fully charged : Steady Green.

Status indicators

Indicates that the speaker
has entered into the pairing
mode and it is ready to be

the first me

Indicates that the device is
successfully paired

Indicates that the device has
switched to the auxiliary
input mode

Indicates that the device has
switched to the TF mode

Baery is charging

Baery is fully charged

Center indicator/
Control buon

Baery status

indicator

Flashing blue

Steady blue

Steady red

Steady Green

Steady red

Steady green

Wonders Technology Co.,Ltd
Email:[e-mail]

IV. Preparaon

• Use the supplied USB cable to charge your portable speaker directly

from your computer or device with a micro USB port.

• Make sure that the speaker is fully charged before using it for the
first me.

• The portable speaker baery has to be inially charged for at least
12 hours. Thereaer, the baery will take from 2 to 3 hours to recharge.

• While charging, the LED glows red. When the baery has reached full
capacity, the LED will change to green.

• To turn on the speaker, press and hold the power buon for several
seconds. Press and hold the power buon once more to turn off

the device.

Note： The speaker will automacally shut down without any audio

input in 15 minutes.

V. Pairing the wireless speaker with your smart device

1. Place your smart device and wireless speaker no more than one meter
away from each other.

2. Press the power buon located on the back of the speaker for several

seconds to turn it on.

3. Set your smart device to “discover” the wireless speaker. Upon
powering on, a tone will be heard, the blue LED will start flashing,
accompanied by a prompt nofying that the speaker has entered into

the pairing mode.

4. Enabled Bluetooth on your device and choose DOSS SoundBox from
the list.

5. If pairing is successful, the LED will change to steady blue and your
phone will confirm that the connecon has been established. If the
pairing process fails aer 60 seconds, please repeat steps 1 through
5 described above.

VI. Answering and ending a call using your speaker or
mobile phone

1. When there is an incoming call, the speaker will generate a tone and
a verbal noficaon to alert you of this event.

2. Briefly press the Handset buon to pick up, long press to reject.
You may also press the answer buon on your smart phone to take the

call using the speaker.

3. Speak with a clear voice right into the built-in microphone located on
the front secon of the speaker.

4. To end a call, tap the Handset buon once again. Likewise, you

may also end the call directly using the command on your cell phone.

5. When listening to music using your smart phone, playback will resume
automacally once the call has ended.

VII. Product specificaons

Product type: Wireless Portable Bluetooth Speaker with Built-in

Microphone

Output power: 6W x 2
Driver unit: 1.5 inch speaker x 2 + 2.6 inch passive radiator

Frequency response: 100Hz-18kHz

Signal to noise rao: ≤ 55dB
Unit weight: 560 g

Unit dimension: 6.6 x 2.7 x 2.9 inch

Warranty: One-year limited

VIII. Power

• Baery type: Li-ion 3.7V, 2200mAh

• Input:5V 1A

• Baery charge up me: 3 hours approximately (when fully depleted).

• Baery playback me: up 12 hours (duraon me may vary depending
on the volume level used and usage paerns).

IX.Wireless/Networking

• Bluetooth specificaon: V4.0+EDR, backwards compable with previous

Bluetooth versions

• Profiles supported

• A2DP (Advanced Audio Distribuon Profile)

• Maximum operaon range: 10 meters / 33 

X. Warning

• Do NOT drop, hit or shake the device.

• Do NOT disassemble, repair or modify the Bluetooth speaker by yourself.

• Do NOT use cleaning products that contain benzene, solvents or alcohol.

• Do NOT expose the Bluetooth speaker to excessive heat or to direct
sunlight for long periods of me.

• Do NOT store the device in a place with high humidity or dust.

• Do NOT place heavy objects on top of the Bluetooth speaker.

• Do NOT use near a microwave oven or wireless LAN products.

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.