Wolo EE100 User Manual
INSTALLATION INSTRUCTIONS
FOR MODEL EE100 ELECTRONIC INDUSTIAL HORN 12 – 60 Volt DC
Your purchase of a Wolo industrial horn is a perfect choice for your equipment for both new and replacement
requirements. Wolo’s products are manufactured with the finest materials. Each horn is tested to ensure it meets all
manufacturing specifications, before it is packaged. If you need help installing this product, our technicians are available
to answer your questions, Monday through Friday from 9AM to 4 PM EST by calling 1-888-550-HORN (4676).
IMPORTANT: The EE100 has an operating voltage range of 12-60 VDC; before installing this horn make sure the
voltage rating matches the vehicles operating voltage and or horn system’s voltage. The EE100 will automatically sense
and adjust to any operating voltage within the range of 12-60 VDC. There is no adjustment or setting that the installer
has to make.
MOUNTING FIG. #1
1. Remove the factory horn, and install the EE100 in the same location. When
possible face the horn downward to prevent dirt and water from entering into the
horn. To secure the EE100 to the selected location drill a 5/8” hole. Place the bolt
that is provided into the drilled hole and thread the nut/lock washer onto the bolt,
two to three turns. Slide the horn onto the head of the bolt using the slotted track
on the side of the EE100. Secure the horn to the vehicle by tightening the nut/lock
washer.
WIRING
TWO (2) TERMINAL WIRING FIG. #2
(Replacement Installation, for vehicles that have an existing horn system)
2. For vehicles where the factory horn wires are connected
to two (2) horn terminals, simply transfer the factory horn
wires to the power plug provided with the EE100, follow
steps 3-6 below.
3. The RED WIRE of the power plug provided is connected
to the vehicle’s horn wire that is (+) positive.
4. The BLACK WIRE of the power plug provided is
connected to the vehicle’s horn wire that is (-) negative.
5. Carefully inspect the horn wires before connecting them to the power plug so to ensure that they are clean and free of
dirt and corrosion. IMPORTANT: Always make sure that a 3-amp inline fuse is used in the horn circuit to protect the
vehicle, (fuse not included). Make sure all connections are taped and secured.
6. Connect the plug to the EE100. The horn installation is complete and the horn is ready to be used.
ONE (1) TERMINAL WIRING FIG. #3
(Replacement Installation, for vehicles that have an
existing horn system)
7. For vehicles where the factory horn wire is connected
to one (1) horn terminal, simply transfer the factory
horn wire to the power plug provided with the EE100,
follow steps 7-10 below.
8. The RED WIRE of the power plug provided is
connected to the vehicle’s horn wire that is (+) positive.
9. The BLACK WIRE of the power plug provided is connected to ground, (-) negative, using any of the following
locations: under any clean metal body bolt or the negative post of the battery. Always make sure the metal ground
surface is free of paint, rust and oxidation.
10. Carefully inspect the horn wire before connecting it to the power plug so to ensure that they are clean and free of dirt
and corrosion. IMPORTANT: Always make sure that a 3-amp in-line fuse is used in the horn circuit to protect the
vehicle, (fuse not included). Make sure all connections are taped and secured.
ANY EXPRESSED WARRANTY NOT PROVIDED HEREIN IS EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF THREE (3) MONTHS. UNDER NO CIRCUMSTANCES SHALL WOLO BE LIABLE TO
PURCHASER OR ANY OTHER PERSON FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING OUT OF BREACH OF WARRANTY OR OTHERWISE.
To obtain warranty service, return the product prepaid, and include the original bill of sale showing the date of
purchase. Provide with the return a brief description of the problem. Also, include with the return a check or money
order in the amount of $20.00 to cover return shipping. Mail to:
Wolo Manufacturing Corp.
Attn: Warranty Service
One Saxwood Street
Deer Park, NY 11729
E-mail: tech@wolo-mfg.com
Warranty
Wolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date
of purchase, that this product is free from defects in workmanship and materials. If there is such a proven
defect, Wolo, at its option, will either repair or replace the item free of charge, if it is returned to Wolo within
three months from the date of purchase together with proof of purchase as described below. Wolo reserves the
right to inspect any defect prior to settling any warranty claim by repair or replacement. This warranty is limited
as above provided and Wolo will not be responsible for fire or other casualty or accident, due to neglect,
abuse, abnormal use, modifications, faulty installation of this product, or natural causes.
© 2008 Wolo Mfg. Corp All Rights Reserved.
11. Connect the plug to the EE100. The horn installation is complete and the horn is ready to be used.
INSTALLATION USING A NEW HORN BUTTON SWITCH FIG. #4
12. The RED WIRE of the power plug provided
is connected to a (+) positive power source
such as; battery, alternator, fuse block and
etc. Use 16-gauge or heavier wire.
IMPORTANT: Always make sure that there is
a 3-amp inline fuse used in the horn circuit to
protect the vehicle, (fuse not included).
13. The BLACK WIRE of the power plug
provided is connect to the horn switch,
(switch not included).
14. Connect the horn switch’s other terminal to ground, any metal body surface that is clean of paint and rust.
15. Connect the plug to the EE100. Make sure all connections are taped and secured. The horn installation is
complete and the horn is ready to be used.
Loading...