Wolo 357 User Manual

INSTALLATION INSTRUCTIONS

FOR 357 SERIES DISC HORN

Your purchase of a Wolo horn is a perfect choice for a new or replacement requirements. Wolo’s products are
manufactured with the finest materials. Each horn is tested to ensure it meets all manufacturing specifications, before it
is packaged. If you need help installing this product, our technicians are available to answer your questions, Monday
through Friday from 9AM to 4 PM EST by calling 1-888-550-HORN (4676).

IMPORTANT: This horn is available in different voltage ratings; before installing this horn make sure
the voltage rating matches the vehicles operating voltage and or horn system's voltage.

MOUNTING FIG. #1

1. Remove the factory horn, and install your new Wolo horn in
the same location. When possible face the horn downward
to prevent dirt and water from entering into the horn. Secure
the horn to the vehicle using the bracket and hardware
provided. NOTE: there are two different bracket mounting
holes that can be used, flat surface or 90 degree.

TWO (2) TERMINAL WIRING FIG. #2

(Replacement Installation, for vehicles that have an existing
horn system)

2. For vehicles where the factory horn wires are connected to
two (2) horn terminals, simply transfer the factory horn wires
to the new Wolo horn. Carefully inspect the horn wires
before connecting them to your new Wolo horn to ensure
that they are clean and free of dirt and corrosion. It doesn’t
make a difference which horn terminal is used on your new
Wolo horn when transferring the wires from your factory
horn. Make sure the horn’s screw terminals are securely
tightened. NOTE: If the horn you are replacing required wire terminals, they will not be required
and they will need to be removed from the horn wires. IMPORTANT: Always make sure that there
is an inline fuse used in the horn circuit to protect the vehicle, see chart on opposite side for
correct amperage, (fuse not included). The horn installation is complete and the horn is ready to
be used. Make sure wire are sure and safe.

ONE (1) TERMINAL WIRING FIG. #3

(Replacement Installation, for vehicles that have an existing
horn system)

3. For vehicles where the factory horn wire connects to only
one (1) horn terminal. Transfer the factory horn wire to
your new Wolo horn. It doesn’t make a difference which
horn terminal is use when transferring the wire from your
factory horn. If the horn you are replacing required a wire
terminal, it is not required and will need to be removed
from the horn wire. Carefully inspect the horn wire before
connecting it to your new Wolo horn so to ensure that it is
clean and free of dirt and corrosion.

4. The other horn terminal is connected to ground using any of the following locations; under the
horn’s mounting bolt if mounted on a metal body surface, under any clean metal body bolt or the
negative post of the battery. Always make sure the metal ground surface is free of paint, rust and
oxidation.

Fig. 1

5/16”

5/16”

Fig. 2

Fig. 3

ANY EXPRESSED WARRANTY NOT PROVIDED HEREIN IS EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF THREE (3) MONTHS. UNDER NO CIRCUMSTANCES SHALL WOLO BE LIABLE TO
PURCHASER OR ANY OTHER PERSON FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING OUT OF BREACH OF WARRANTY OR OTHERWISE.

To obtain warranty service, return the product prepaid, and include the original bill of sale showing the date of
purchase. Provide with the return a brief description of the problem. Also, include with the return a check or money
order in the amount of $20.00 to cover return shipping. Mail to:

Wolo Manufacturing Corp.

One Saxwood Street

Deer Park, NY 11729

Attn: Warranty Service

Warranty

Wolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date
of purchase, that this product is free from defects in workmanship and materials. If there is such a proven
defect, Wolo, at its option, will either repair or replace the item free of charge, if it is returned to Wolo within
three months from the date of purchase together with proof of purchase as described below. Wolo reserves the
right to inspect any defect prior to settling any warranty claim by repair or replacement. This warranty is limited
as above provided and Wolo will not be responsible for fire or other casualty or accident, due to neglect,
abuse, abnormal use, modifications, faulty installation of this product, or natural causes.

© 2008 Wolo Mfg. Corp All Rights Reserved.

5. Attach the other end of the grounding wire to the unused horn terminal. Make sure the horn’s

screw terminals are securely tightened. IMPORTANT: Always make sure that there is an
inline fuse used in the horn circuit to protect the vehicle, see chart below for correct
amperage, (fuse not included). The horn installation is complete and the horn is ready to be
used. Make sure wire are sure and safe.

INSTALLATION USING A NEW HORN BUTTON SWITCH FIG. #4

6. Connect one of the horn’s terminals to a (+) positive power source such as: battery, alternator,

fuse block and etc. Use 16-gauge or heavier wire. IMPORTANT: Always make sure that there
is an inline fuse installed within six inches of the connection point to protect the vehicle, see
chart below for correct
amperage, (fuse not
included). Make sure wire
are sure and safe.

7. Connect the horn’s other

terminal to the horn switch,
(switch not included).

8. Connect the other horn

switch terminal to ground,
any metal body surface that
is clean of paint and rust.
Installation is complete.

Voltage 12 24 36

Fuse 6-amp 3-amp 3-1mp

Fig. 4