Wolo 3367P-G User Manual

Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Our warning lights

are manufactured with the finest of materials and each light is tested before it is packaged.Quality
workmanship and components are Wolo’s assurance of a product that will provide years of dependable
service.

Before installation of this warning light is attempted, it is important to read these instructions completely. The
lives of people are dependent on proper installation. The person installing this light must have advanced
knowledge of the proper method of installing warning lights to a vehicle, as well as, knowledge of the
vehicle's electrical system. Again, read this manual completely and note any messages marked
‘‘IMPORTANT” or ‘‘WARNING”. A safe installation will prevent serious injury and/or damage to the vehicle.

IMPORTANT: Installation of this warning light may require drilling to the vehicle. The installer must carefully
inspect both sides of any location that will be drilled to ensure that there are no components, wires and/or any
vehicle parts that could be damaged when drilling.

IMPORTANT: Always de-burr any drilled holes to ensure that there are no sharp edges. Install the plastic
grommet into the hole that the wires are being routed through. Always refer to the vehicle’s shop manual for
the deployment location of the air bags. Never install the on/off switch, wires and/or components in the
deployment area of any air bag. Improper installation could reduce the effectiveness of the vehicle's air bag
system and/or project an object that could cause serious personal injury or death to the driver or passenger.
The user/installer assumes all responsibility to properly assess a
safe mounting location for the switch to ensure ultimate safety to
the driver and passengers inside the vehicle.

WARNING: This warning light contains a high intensity strobe
bulb. To prevent permanent eye damage, DO NOT stare into the
light beam at close range.

MOUNTING WITH SCREWS (FIG. A & B)

1. Select the location you wish to mount the warning light. For
best results, the installer should make sure the lens is
unobstructed so that the light can be seen at 360 degrees.

2. Using the holes in the warning light’s base, mark the three (3)
hole locations for mounting the light. Remove the warning light
from the mounting location and drill holes using a 3/16” drill bit.
NOTE: There are two methods to route the warning light’s wires:
2A. Route the wires through the notch in the base of the light.
2B. Route the wires through a hole directly under the base of the

warning light.

3. If needed, drill a hole for the wires, using a 5/16” drill bit. De-burr
the drilled hole and insert the provided plastic grommet into the
hole. The plastic grommet will ensure that there are no sharp
edges around the hole that could damage the wires. IMPORTANT:
If waterproofing is required, use silicone sealant around wires and
plastic grommet.

4. Secure the base of the warning light to the vehicle using only the
hardware provided. To prevent vibration and water leaks, use the
metal ring and gasket provided. Position the ring and gasket so the
holes in the ring align with the base and the rubber gasket.

INSTALLATION INSTRUCTIONS FOR

BRIGHT STAR STROBE WARNING LIGHT

Permanent Mount Model 3350P-A, 3355P-B,

3360P-R, 3365P-C & 33 P-G

FIG. A

FIG. B

67

WIRING WARNING LIGHT (Fig. C)

5. RED WIRE: Is connected to 12-110 volts (+) positive. Using the inline fuse provided, connect the red wire
to the vehicle’s fuse block or (+) positive battery post. Remove fuse from the inline fuse holder until all
wiring has been completed.

6. BLACK WIRE: Is connected to the on/off switch (not provided).

7. Connect the switch’s other terminal or wire to ground, by placing the wire under the battery’s negative (-)
post or any metal body bolt that is clean of paint and rust.

8. Insert the fuse into the fuse holder and position the switch to ON. The light will turn on and operate.

WARNING: This warning light produces high voltage, which is stored in the electronic circuit and could cause
property damage, serious injury or death to you or others. Always disconnect the power to the light and wait
at least five minutes before attempting to perform any service to the light.

If you need help installing your new Wolo BRIGHT STAR strobe warning light, our technicians are available to
answer your questions Monday thru Friday 9 AM to 4 PM EST at 888-550-4676.

ANY EXPRESSED WARRANTY NOT PROVIDED HEREIN IS EXCLUDED AND DISCLAIMED. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM
OF THREE (3) MONTHS. UNDER NO CIRCUMSTANCES SHALL WOLO BE LIABLE TO PURCHASER OR ANY OTHER PERSON
FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY OR OTHERWISE.

To obtain warranty service, return the product prepaid and include the original bill of sale showing the date of purchase. Provide with
the return a brief description of the problem. Also, include with the return a check or money order in the amount of $10.00 to cover
return shipping. Mail to:

Wolo Manufacturing Corp.

One Saxwood Street, Deer Park, NY 11729

Attn: Warranty Service

E-mail: [e-mail]

© 2011 Wolo Mfg. Corp All Rights Reserved.

WARRANTY

Wolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date of purchase, that
this product is free from defects in workmanship and materials. If there is such a proven defect, Wolo, at its option, will either repair
or replace the item free of charge, if it is returned to Wolo within three months from the date of purchase together with proof of
purchase as described below. Wolo reserves the right to inspect any defect prior to settling any warranty claim by repair or
replacement. This warranty is limited as above provided and Wolo will not be responsible for fire or other casualty or accident, due
to neglect, abuse, abnormal use, modifications, faulty installation of this product, or natural causes.

FIG. C

12-110 VDC

BATTERY