Wolo 3077P-G User Manual

Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Our warning lights are
manufactured with the finest of materials and each light is tested before it is packaged. Quality workmanship
and components are Wolo’s assurance of a product that will provide years of dependable service.

Before installation of this warning light is attempted, it is important to read these instructions completely. The
lives of people are dependent on proper installation. The person installing this light must have advanced
knowledge of the proper method of installing warning lights to a vehicle, as well as, knowledge of the
vehicle's electrical system. Again, read this manual completely and note any messages marked

‘‘IMPORTANT” or ‘‘WARNING”. A safe installation will prevent serious injury and/or damage to the vehicle.

IMPORTANT: Installation of this warning light may require drilling to the vehicle. The installer must carefully

inspect both sides of any location that will be drilled to ensure that there are no components, wires and/or any
vehicle parts that could be damaged when drilling.

IMPORTANT: Always de-burr any drilled holes to ensure that there are no sharp edges. Install the plastic
grommet provided into the hole that the wires are being routed through. Always refer to the vehicle’s shop
manual for the deployment location of the air bags. Never install the on/off switch, wires and/or components
in the deployment area of any air bag. Improper installation could reduce the effectiveness of the vehicle's air
bag system and/or project an object that could cause serious personal injury or death to the driver or
passenger. The user/installer assumes all responsibility to properly access a safe mounting location for the
switch to provide ultimate safety to the driver and passengers
inside the vehicle.

WARNING: This warning light contains GEN 3 high intensity
LEDs. To prevent permanent eye damage, DO NOT stare into
the light beam at close range.

MOUNTING WITH SCREWS (FIG. A & B)

1. Select the location you wish to mount the warning light. For
best results, the installer should make sure the lens is
unobstructed so that the light can be seen at 360 degrees.

2. Using the holes in the warning light’s base, mark the three
(3) hole locations for mounting the light. Remove the warning light from the
mounting location and drill holes using a 3/16” drill bit.
NOTE: There are two methods to route the warning lights’
wires:
2A. Route the wires through the notch in the base of the light.
2B. Route the wires through a hole directly under the base of

the warning light.

3. If needed, drill a hole for the wires using a 5/16” drill bit. De­burr the drilled hole and insert the provided plastic grommet
into the hole. The plastic grommet will ensure that there are no
sharp edges around the hole that could damage the wires.
IMPORTANT: If waterproofing is required, use silicone sealant
around wires and plastic grommet.

4. Secure the base of the warning light to the vehicle using only
the hardware provided. To prevent vibration and water leaks,
always use the rubber gasket provided.

INSTALLATION INSTRUCTIONS FOR APOLLO 1

GEN 3 LED WARNING LIGHT

Model 3060P-A, 3065P-B, 3070P-R,

3075P-C & 3077P-G

FIG. A

FIG. B

WIRING WARNING LIGHT (Fig. C)

5. RED WIRE: Is connected to 12-100 volts (+) positive. Using the inline fuse provided, connect the red wire
to the vehicles fuse block or (+) positive battery post. Remove fuse from the inline fuse holder until all
wiring has been completed.

6. BLACK WIRE: Is connected to the on/off switch (not provided).

7. Connect the switch’s other terminal or wire from the on/off switch to ground, by placing the wire under the
battery’s negative (-) post or any metal body bolt that is clean of paint and rust.

8. Insert the fuse into the fuse holder and position the switch to ON. The light will turn on and operate.

If you need help installing your new Wolo APOLLO 1, our technicians are available to answer your questions
Monday thru Friday 9 AM to 4 PM EST at 888-550-4676.

ANY EXPRESSED WARRANTY NOT PROVIDED HEREIN IS EXCLUDED AND DISCLAIMED. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM
OF THREE (3) MONTHS. UNDER NO CIRCUMSTANCES SHALL WOLO BE LIABLE TO PURCHASER OR ANY OTHER PERSON
FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY OR OTHERWISE.

To obtain warranty service, return the product prepaid, and include the original bill of sale showing the date of purchase. Provide with
the return a brief description of the problem. Also, include with the return a check or money order in the amount of $10.00 to cover
return shipping. Mail to:

Wolo Manufacturing Corp.

One Saxwood Street, Deer Park, NY 11729

Attn: Warranty Service

E-mail: [e-mail]

© 2011 Wolo Mfg. Corp All Rights Reserved.

WARRANTY

Wolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date of purchase, that
this product is free from defects in workmanship and materials. If there is such a proven defect, Wolo, at its option, will either repair
or replace the item free of charge, if it is returned to Wolo within three months from the date of purchase together with proof of
purchase as described below. Wolo reserves the right to inspect any defect prior to settling any warranty claim by repair or
replacement. This warranty is limited as above provided and Wolo will not be responsible for fire or other casualty or accident, due
to neglect, abuse, abnormal use, modifications, faulty installation of this product, or natural causes.

FIG. C

12-100 VDC