Wolf Appliance Company ICBIG15-S User Manual 2

GRILL MODULE
INSTALLATION INSTRUCTIONS
MÓDULO DE PARRILLA INSTRUCCIONES DE INSTALACIÓN
GRIL INSTRUCTIONS D’INSTALLATION
PIANO GRILL ISTRUZIONI PER L’INSTALLAZIONE
ENGLISH 4
ESPÃNOL 13
ITALIANO 31
3
CONTACT INFORMATION
Website: wolfappliance.com
As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip­ment. There are two types of potential hazards that may occur during installation.
WOLF®is a registered trademark of Wolf Appliance, Inc.
signals a situation where minor injury or product damage may occur if you do not follow instructions.
states a hazard that may cause serious injury or death if precautions are not followed.
Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation.
WOLF GRILL MODULE
INSTALLATION REQUIREMENTS
IMPORTANT NOTE:
Save these Installation
Instructions for the local inspector’s use.
Please read the entire Installation Instructions prior to installation.
This installation must be completed by a qualified technician.
Installer:
please retain these instructions for local inspector’s reference, then leave them with the homeowner.
Homeowner:
please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.
IMPORTANT NOTE:
This appliance must be installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate.
Record the model and serial numbers before installing the grill module. Both numbers are listed on the product rating plate located on the underside of the module. Refer to the illustration below.
BEFORE YOU STA RT
IMPORTANT NOTE:
Installation and service must be performed by a qualified installer or service agency.
Installation of the grill module must meet the minimum clearance requirements for safe operation. Refer to Site Preparation on page 6.
If the grill module is to be used with any combination of additional cooktop units or modules, refer to Multiple Cooktop Installa­tion on page 8.
Electrical installation must be adequate and in compliance with all local codes and ordinances. Electrical ground is required, refer to Electrical Requirements on page 9.
IMPORTANT NOTE:
A ventilation hood is recommended (but not required) for use with the Wolf electric grill module.
This module is intended for indoor use.
Model ICBIG15/S
Model Number
ICBIG15/S
Serial Number
Locationofrating
plate under module
Rating plate location
5
WOLF GRILL MODULE
SITE PREPARATION
IMPORTANT NOTE:
Installation of the Wolf electric grill module must meet the following location requirements. All dimensions listed are minimum requirements for safe operation. Refer to the illustration below.
To eliminate the risk of burns or fire by reaching over heated surface units,
abinet storage space located above the
c surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a ventilation hood that projects horizontally a minimum of 127 mm beyond the bottom cabinets.
C
G
D
LOCATION IN COUNTERTOP
A)
Minimum flat countertop surface. Must be equal to or greater than the width of the module(s).
B)
Minimum 152 mm wide clearance from the module side edge to any combustible surface up to 457 mm above the countertop (noted by shaded area).
OVERHEAD CABINET DIMENSIONS
C)
Minimum spacing between overhead side cabinets must be greater than or equal to the nominal width of the module(s).
D)
Minimum 457 mm vertical distance from the countertop to the bottom of side cabinets within minimum side clearance.
E)
Minimum vertical distance between the countertop and combustible materials above the module must be 762 mm.
F)
Minimum 25 mm from rear wall.
G)
Maximum 330 mm depth of overhead and side cabinets directly above and within side clearance.
E
F
Minimum installation clearances
6
Failure to locate the cooktop module without the proper clearances will result in a fire hazard.
B
A
B
INSTALLATION INSTRUCTIONS
INSTALLATION SPECIFICATIONS
The illustrations below provide the overall dimensions, finished cut-out dimensions and electrical placement for the Wolf electric grill module.
The grill module is designed to fit a standard 610 mm deep base cabinet with 635 mm deep countertop. Before making the countertop cut­out, verify that the module will clear the side walls of the base cabinet below.
A grounded junction box needs to be placed within 1.2 m of the right rear of the module. Locate electrical with the shaded area of the illustration below.
MODEL ICBIG15/S DIMENSIONS
Overall Width 381 mm
Overall Height 159 mm
Overall Depth 533 mm
Minimum Cabinet Depth 578 mm
Minimum Height Clearance 159 mm
Cut-Out Width 356 mm
Cut-Out Depth 489 mm
Unit dimensions may vary to ± 3 mm.
Overall Dimensions
Installation Specifications
Countertop Cut-Out Dimensions
7
WOLF GRILL MODULE
MULTIPLE COOKTOP INSTALLATION
IMPORTANT NOTE:
If the grill module is to be used with a combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 32 mm for each additional unit.
When multiple units are installed side by side, each unit must have its own separate recom­mended electrical circuit.
When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is recommended.
IMPORTANT NOTE:
Review specific installation instructions for product to product capabilities.
Countertop cut-out dimensions for installation of multiple cooktops
8
WOLF GRILL MODULE
ELECTRICAL REQUIREMENTS
Attach the power cord to the unit before plugging the cord into the wall.
Required Power Supply
220–240 V AC, 50–60 Hz, 15 amp service
Maximum Connected Load
2.8 kW
The Wolf electric grill module requires 15 amp service with its own circuit breaker or fuse. Locate electrical within the shaded area shown in the illustration on page 7. A properly rated cord should be attached to the power supply box of the grill as shown in the illustration below. Open the power box to expose the screws with corresponding numbers. Loosen the 1, 5, and ground screws. Run the cord through the circular hole and into the power supply box. Attach the Neutral wire to the number 1 position. Attach the line wire to the 5 position and attach the ground wire to the corresponding ground screw. After tightening the screws, close the cover to the power supply box without pinching any of the wires.
IMPORTANT NOTE:
The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate located on the underside of the module. Refer to the illus­tration on page 5. The wiring diagram covering the control circuit is located inside the module control box.
The complete appliance must be properly grounded at all times when electrical power is applied.
Improper connection can result in a fire hazard!
IMPORTANT NOTE:
To avoid electrical shock when disconnecting the grill module, all poles/wires must be disconnected from the power supply box.
You must follow all local codes and ordinances when installing your service.
Power supply box
9
INSTALLATION INSTRUCTIONS
MODULE INSTALLATION
To prevent pollution from entering the controls area, attach the foam strip to the underside of the module frame. Refer to the illustration below.
Gently lower the grill module into the cut-out area in the countertop and center. Check that the front edge of module is parallel to the front edge of the countertop. Check that all required clearances are met.
To attach the brackets to the sides of the module, insert the clip into the rectangular punchout in the pan, and push down. Install the clamping screw into the bracket and tighten until the screw contacts the underside of the countertop. Do not overtighten screws. Refer to the illustration below.
IMPORTANT NOTE:
Do not use caulk or silicone to seal the module to the countertop. The unit must be readily removable for service.
BEFORE OPERATING
Read the entire Wolf Grill Module Use & Care Information included with the module. Impor­tant safety, service and warranty information is contained within the book.
Thoroughly clean the grilling grate, grease deflection plates and grease collection pan with mild soap and water before use.
10
Foam strip Installation brackets
WOLF GRILL MODULE
MODULE REMOVAL
IMPORTANT NOTE:
Removal of the grill module should only be performed by a Wolf authorized service center technician.
If removing the grill module is necessary for cleaning or service, first disconnect the electric supply. Remove the mounting brackets on each side of module and remove. To reinstall, refer to page 10.
The module must be disconnected from power prior to removal and service.
TROUBLESHOOTING
IMPORTANT NOTE:
If the grill module does not operate properly, follow these troubleshooting steps:
Verify that power is being supplied to the module.
Check electrical connections to ensure that the installation has been completed correctly.
Follow troubleshooting procedures as described in the Wolf Grill Module Use & Care Information.
If the module still does not work, contact a Wolf authorized Wolf dealer. Do not attempt to repair the cooktop module yourself. Wolf is not responsible for service required to correct a faulty installation.
11
INSTALLATION INSTRUCTIONS
IF YOU NEED SERVICE
For service in your area, contact either your Wolf dealer or visit the showroom locator page of our website,
wolfappliance.com
find the regional distributor by country.
to
CONTACT INFORMATION
Website: wolfappliance.com
When calling for service, refer to the model and serial number of the grill module. Both numbers are listed on the product rating plate located on the underside of the module. Refer to the illustration on page 5.
12
The information and images are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any informa­tion or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc.
©Wolf Appliance, Inc. all rights reserved.
+ 28 hidden pages