Wolf WRS-K Configuration Manual

Conguration wizard

WRS-K

WOLF GMBH / POSTFACH 1380 / D-84048 MAINBURG / TEL. [phone] / FAX [phone] / www.WOLF.eu

Part no.: 3062933_201707

Subject to technical modications

GB

2

3062933_201707

Contents

Contents ................................................................................................................... 2

Installation / commissioning / operating overview .................................................... 3

Post-conguration, air quality / CO

2

sensor .............................................................. 4

Post-conguration remote control............................................................................. 5

Post-conguration, LON / BacNet / ModBus / Ethernet / KNX interface .................. 6

Post-conguration, pressure control / ow rate control / cooling function ................ 7

New conguration controller ..................................................................................... 8

System conguration .............................................................................................. 12

Conguration for pressure or ow rate control ....................................................... 15

Notes ...................................................................................................................... 19

3

3062933_201707

1 Displaying and acknowledging active fault messages

2 Displaying the system operating data (set / actual values)

3 Access to the main menu

4 Forward scrolling within a menu and increasing values

5 Switching the system ON and OFF, selecting menu points, conrming inputs

6 Backwards scrolling within a menu and reducing values

1. Commissioning

- According to EN 50110-1, only qualied electricians may carry out the installation and commissioning of
the ventilation control unit and connected accessories.

- Observe all regulations stipulated by your local power supply utility and all VDE or local regulations.

- DIN VDE 0100 regulations regarding the installation of high voltage systems up to 1000 V.

- DIN VDE 0105-100 operation of electrical systems.

- Only original Wolf accessories may be used (electric heater bank, condensate pump, servomotors, etc.),
otherwise, Wolf cannot provide a warranty.

Installation / commissioning /
operating overview

1

2

3

4

5

6

Operating overview

4

3062933_201707

2. When retrotting an air quality sensor (mixed gas or VOC, CO2) follow the instructions below.

Post-conguration, air quality / CO2 sensor

Conguration Activation

Other

Air quality sensor

No

Using ↑ ↓ select "Air quality sensor"
and press Enter to activate re-
conguration.
Select "Yes" with and conrm with
Enter

Other

Air quality sensor
available? >Yes

U08 KLM-M/L
Type 0-10V
Version VOC

Use Enter to conrm the input port
"U8" and type "0-10 V"
Use to select the variant "VOC" or
"CO2"

FR

20.03.09

11:02

21.0

11.4°C 18.5°C

PRG OPERATING DATA

Esc MENUS

ON/OFF

SET VALUE

Press

EscEsc

button

Select 1234 with

and conrm with

Enter

wolf-heiztechnik.de

Contractor

Password: 1234

Continue with

Select "Heating contractor" with and
conrm with Enter

Main menus

Standard settings

Displays

Time functions

Contractor

DISPLAYSSELECTIONEsc BACK

Alarm management
Service

Other

Contractor - menus

DISPLAYSELECTIONEsc BACK

Select "Other" with and conrm with
Enter

DISPLAYSELECTIONEsc BACK

DISPLAYSAVEEsc BACK

5

3062933_201707

Post-conguration remote control

Backup mode
Night ventilation

Other

Contractor - menus

DISPLAYSELECTIONEsc BACK

Select "Other" with and conrm with
Enter

Select "Remote control" with and
conrm with

DISPLAYSELECTIONEsc BACK

Other...

Remote control

installed? No

Select "Yes" with and conrm with
Enter

DISPLAYSELECTIONEsc BACK

Other...

Remote control

installed? Yes

Switch power supply to control unit OFF
and ON again
The remote control is enabled

Conguration

Restart system

(mains OFF/ON)

System restart

FR

20.03.09

11:02

21.0

11.4°C 18.5°C

PRG OPERATING DATA

Esc MENUS

ON/OFF

SET VALUE

Press

EscEsc

button

Select 1234 with

and conrm with

Enter

wolf-heiztechnik.de

Contractor

Password: 1234

Continue with

3. Proceed as follows to re-congure a remote control

Select "Heating contractor" with and
conrm with Enter

Main menus

Displays

Time functions

Contractor

DISPLAYSSELECTIONEsc BACK

6

3062933_201707

FR

20.03.09

11:02

21.0

11.4°C 18.5°C

PRG OPERATING DATA

Esc MENUS

ON/OFF

SET VALUE

Press

EscEsc

button

Main menus

Standard settings

Displays

Time functions

Contractor

DISPLAY

SELECTION

Esc BACK

Select "Heating contractor" with and
conrm with Enter

Select 1234 with and conrm with
Enter

Contractor

Password: 1234

Continue with

wolf-heiztechnik.de

4. Proceed as follows for the re-conguration of a LON / BacNet / Modbus / Ethernet / KNX
interface.

Post-conguration, LON / BacNet /
Modbus / Ethernet / KNX interface

Conrm with

Other...

BMS protocol
>LON-Works
Transfer speed
>4800 (RS485/RS422)
BMS address: 001

VALUESAVEEsc CANCEL

Select required connection with

- No proto

- pCO Manager

- LON-Works

- Bac-Net

- Modbus Stave Standard

- Ethernet

- KNX

and conrm with Enter

Other...

Protocol type:
BacNet

VALUESAVEEsc CANCEL

BMS protocol has been set
Hold down

EscEsc

button until you jump to

the standard screen

Select "Other" with

and conrm with

Enter

Alarm management
Service

OtherNight ventilation

Limits

Contractor - menus

DISPLAYSELECTIONEsc BACK