Wolf SPO30TMSTH, SPO30PMSPH, SPO30CMBTH, SPO30TEST, SPO24TESTH Installation Guide
SPEED OVEN
INSTALLATION GUIDE
SPECIFICATIONS, INSTALLATION, AND MORE
SPEED OVEN
Contents
3 Speed Oven
4 Specications
7 Installation
7 Troubleshooting
Features and specications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
2 | Wolf Customer Care 800.222.7820
SPEED OVEN
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located on the lower left side of the front face
frame. The oven door must be open to view the rating plate.
Refer to the illustration below.
If service is necessary, contact Wolf Factory Certied
Service with the model and serial number. For the name of
the nearest Wolf Factory Certied Service or for questions
regarding the installation, visit the contact and support
section of our website, wolfappliance.com, or call Wolf
Customer Care at 800-222-7820.
Installation Requirements
The speed oven can be installed in a standard or ush inset
application.
Finish the edges of the opening. They may be visible when
the door is open.
For standard installations, the face trim will overlap stiles
and rails. Refer to the chart below.
1
For ush inset installations, a minimum
required on all sides. To ensure consistent reveals, each
corner of the opening must be exactly 90°.
If the speed oven is installed above or below a Wolf E series
oven in a ush inset application, a
INSTALLATION REQUIREMENTS
BASE SUPPORT MIN
24" (610) Model 125 lb (57 kg)
30" (762) Model 125 lb (57 kg)
TRIM OVERLAP 24" MODEL 30" MODEL
Top
Bottom 0" (0) 0" (0)
Sides
/8" (3) reveal is
1
/4" (6) reveal is required.
3
/16" (5)
11
/16" (18) 37/8" (98)
3
/16" (5)
RATING PLATE
Rating plate location
wolfappliance.com | 3
SPECIFICATIONS
Electrical Requirements
Installation must comply with all applicable electrical codes.
Locate the electrical supply as shown in the illustrations on
the following pages. The receptacle may also be located
in an adjacent cabinet within reach of the power cord. A
separate circuit, servicing only this appliance is required. A
ground fault circuit interrupter (GFCI) is not recommended
and may cause interruption of operation. Refer to the illustration below for minimum power cord plug clearance.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded, 240/208 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle NEMA 6-20R grounding type
Power Cord 6'
NEMA
PLUG
(1.8 m)
WARNING
ELECTRICAL SHOCK HAZARD: Plug into a grounded
3-prong outlet. Do not remove the ground prong. Do
not use an adapter. Failure to follow these instructions
can result in electric shock, re, or death.
RATING PLATE
Rating plate location
GROUNDED
NEMA RECEPTACLE
NEMA 6-20R receptacle
1" (25)
MINIMUM
CLEARANCE
Power cord clearance
CORD
4 | Wolf Customer Care 800.222.7820
SIDE
NOTE: 24"
SPECIFICATIONS
Speed Oven
STANDARD INSTALLATION
23" (584)
OPENING
TOP VIEW
DEPTH
1711/16"
(449)
OPENING
HEIGHT
VIEW
(610) and 30" (762) models require the same opening dimensions.
OPENING WIDTH
24" Model 221/8" (562)
30" Model 221/8" (562)
W
E
OPENING WIDTH
FRONT VIEW
W
wolfappliance.com | 5
SIDE
*W
**
SPECIFICATIONS
Speed Oven
FLUSH INSET INSTALLATION
7
/8"
(22)
TOP VIEW
24" (610)
FLUSH INSET
DEPTH
FINISHED
CLEATS*
181/8"
(460)
FLUSH INSET
HEIGHT**
VIEW
ill be visible and should be finished to match cabinetry.
Dimension provides minimum reveals.
FLUSH INSET WIDTH
24" Model 233/4" (603)
W A
13
/16" (21)
30" Model 301/8" (765) 4" (102)
5
E
/16"(8)
A
1
/8" (3)
W
FLUSH INSET WIDTH**
FRONT VIEW
6 | Wolf Customer Care 800.222.7820
Loading...