Wistron NeWeb SWA6 User Manual

Page 1
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
Product Specification
Model Name: AVMD7540-SWA6
(AV7540 +16dBm module with Printing Antenna)
Revision: 1.0
Issue Date: 2010/09/20
This document and the information contained herein is the property of Wistron NeWeb Corporation and reproduction by any means (including, but not limited to, xerographic, chemical, electronic) and distribution is expressly prohibited without prior written consent from Wistron NeWeb Corporation. The document and information contained herein are confidential and may not be divulged without express written consent from Wistron NeWeb Corporation, located at 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C. Copyright 2010 by Wistron NeWeb Corporation / All rights reserved.
Wistron NeWeb Confidential Document
1
Page 2
Wistron
1.0 Add FC
C Descripti
2010/9/20
Amy Tu
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
Revision History
Edition #
0.1 Draft (Initial Revision)
Reason for revision Issue date Author
2010/07/23 Amy Tu
Wistron NeWeb Confidential Document
2
Page 3
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
1. General Description
The AVMD7540-SWA6 module is a complete radio module solution containing all the necessary HW and FW to provide a system-integration ready, multichannel wireless HD audio solution.
The module is comprised of a AV7540 IC combined with RF front-end circuits (RF PA + balun + filter + RF switch), flash memory, crystal, and passive components. The module provides a convenient set of digital I/O interfaces for digital audio through an I2S port, host MCU control through an SPI or I2C interface and optional GPIO for various control and indicator functions.
The module is a card edge style using the 36 pin PCIe card edge connection method to save space and cost in connecting to the main board.
FCC & IC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS
102.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
Wistron NeWeb Confidential Document
3
Page 4
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
2. Features
Complete, Integrated Wireless Module
o AV7540 IC o RF front-end o Flash memory
High Performance Audio and RF solution
o 16 bit, 48kHz to 24 bit, 96kHz digital audio o 120dB SNR Digital Audio Path o Fixed Low Latency solution o +16dBm transmit RF output power o -82dBm receive RF sensitivity o Support for 30m/100m range NLOS/LOS
Digital interfaces and Audio
o 8 channel digital audio I/O (4 I2S ports)
Configurable as input or output
o Stereo audio DAC output o 4-wire SPI slave interface or 2-wire I2C-compatible communication with the host MCU
Package and connections
o Compact size o 36 pin (2x18) PCIe card edge connector o diversity antenna capability
Wistron NeWeb Confidential Document
4
Page 5
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
3. Block Diagram
/
4. Module Outline
Wistron NeWeb Confidential Document
5
Page 6
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
5. Pin Configuration and Definition
Figure 1-1 – AVMD7540-SWA6 module pin configuration
Wistron NeWeb Confidential Document
6
Page 7
Wistron
NeWeb
Table !              -1 AVMD7540-SWA6 pin description
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
# Pin Name Pin Type Description
A1 GND Analog Module ground A2 GND Analog Module ground A3 WCLK2 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 2 – input/output A4 BCLK2 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 2 – input/output A5 ADAT2 Digital I/O I2S audio data, AV75xx physical I2S I/O #2 – input/output A6 WCLK0 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 0 – input/output A7 BCLK0 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 0 – input/output A8 ADAT0 Digital I/O I2S audio data, AV75xx physical I2S I/O # 0 – input/output
A9 SPI/TWI_SEL Digital I/O SPI / TWI interface selection (SPI = 0, TWI = 1) A10 GPIO6 Digital I/O GPIO #6 A11 GPIO4 Digital I/O GPIO #4 A12 GPIO3 Digital I/O GPIO #3 A13 GPIO5 Digital I/O GPIO #5 A14 reserved Digital I/O reserved A15 AGND Analog Audio ground A16 ROUT Analog Audio DAC right channel output A17 LOUT Analog Audio DAC left channel output A18 AGND Analog Audio ground
B1 VCC Analog +5V supply voltage input
B2 VCC Analog +5V supply voltage input
B3 ADAT3 Digital I/O I2S audio data, AV75xx physical I2S I/O # 3 – input/output
B4 BCLK3 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 3 – input/output
B5 WCLK3 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 3 – input/output
B6 MCLK_OUT Digital Output MCLK for I2S audio data
B7 ADAT1 Digital I/O I2S audio data, AV75xx physical I2S I/O # 1 – input/output
B8 BCLK1 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 1 – input/output
B9 WCLK1 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 1 – input/output B10 SDA Digital I/O I2C compatible serial data I/O B11 SCL Digital I/O I2C compatible serial clock I/O B12 S_SSB Digital I/O SPI Slave – slave select (active low) B13 S_SCLK Digital I/O SPI Slave – serial clock B14 S_MOSI Digital I/O SPI Slave – master out slave in B15 S_MISO Digital I/O SPI Slave – master in slave out B16 SRQ/PND Digital Output Notification signal to host (pending notification) B17 SM0 Digital Input Serial Mux control (for flash programming) and module reset (active low)
Wistron NeWeb Confidential Document
7
Page 8
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
6. Electrical Specifications
6.1. Absolute Maximum Ratings
The Absolute Maximum Rating (AMR) corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified.
Table 6-1 6-2 AVMD7540-SWA6 Absolute Maximum Ratings
CONDITION MIN MAX Units
Supply (relative to GND) +5V -0.3 6.0 V
Input Voltage Range – Digital Inputs -0.3 3.6V V Short circuit to GND (any pin) --- continuous Storage Temperature -40 +100 ºC Lead Temperature (10s) -- +225 ºC ESD Voltage Rating – Human Body Model test 2000 V
Wistron NeWeb Confidential Document
8
Page 9
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
6.2. DC Electrical Characteristics
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-2 6-3 AVMD7540-SWA6 DC Electrical Characteristics
PARAMETER CONDITIONS MIN TYP MAX UNIT
Input supply voltage Driven by an external regulator 4.5 5.5 V
Supply Current – (Note 1) RESET 10 mA RX mode: 1 stereo output I2S 100 mA
CMOS I/O Logic Levels – 3.3V I/O
Input Voltage Logic Low, VIL Internal regulator = 3.3V 0.6 V Input Voltage Logic High, VIH Internal regulator = 3.3V 2.0 V Output Voltage Logic Low, VOL Internal regulator = 3.3V; I Output Voltage Logic High, VOH Internal regulator = 3.3V; I
Note 1: The operating states are defined as: RESET = AVMD7540-SWA6 is held in reset by holding SM0 low RX mode: AVMD7540-SWA6 is operating in a link as a client node receiving 1 stereo channel of 16bit,
48kHz audio.
=1mA 0.4 V
LOAD
=1mA 2.9 V
LOAD
6.3. Electrical Characteristics – RF Receiver
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-3 -4 AVMD7540-SWA6 Electrical Characteristics – RF Receiver
PARAMETER CONDITIONS MIN TYP MAX UNIT
RF Channel Frequency Range 2412 Sensitivity (Note 1) TA=25ºC -80 dBm Max Input Signal (Note 1) -5 dBm
2400-2483.5 MHz
Spurious RF outputs
LO leakage -47 dBm
Note 1: Sensitivity and max signal level are defined as the onset of 1% BLER Block Error Rate.
<2400 MHz >2483.5 MHz
2462 MHz
-47
-60
-60
dBm dBm dBm
Wistron NeWeb Confidential Document
9
Page 10
Wistron
®
NeWeb
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
6.4. Electrical Characteristics – RF Transmitter
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-5 -5 AVMD7540-SWA6 Electrical Characteristics – RF Transmitter
PARAMETER CONDITIONS MIN TYP MAX UNIT
RF Performance
RF Channel Frequency Range 2412 Output Power TA=25ºC, OFDM signal, 16MHz channel BW +16 dBm Harmonics (Note 1) 2nd harmonic
Conducted RF Spurious signals 800-1000MHz
Radiated Spurious RF signals 30-88MHz,
LO leakage Relative to power in a 100kHz BW **, after DC
Note 1: Measured at TX output power = +16dBm Note 1: Measured at TX output power = +16dBm
2462 MHz
3rd harmonic
2000-2390MHz
2483.5- 3000MHz; RBW=1MHz 3000-4000MHz ; RBW=1MHz
4.0-26.5GHz; RBW=1MHz
88-216MHz 216-960MHz >960MHz
offset correction
-45
-45
-45
-45
-45
34 37 40 48
-20 dBc
dBm dBm dBm dBm dBm
dBuV/
dBuV/
dBuV/
dBuV/
m
m
m
m
6.5. Electrical Characteristics – RF Channel Frequency
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-5 -6 AVMD7540-SWA6 Electrical Characteristics – RF Transmitter
PARAMETER CONDITIONS MIN TYP MAX UNIT
RF Performance
Channel Frequency
Wistron NeWeb Confidential Document
AM2G system channel 1 AM2G system channel 2 AM2G system channel 3
2412 2438 2462
MHz MHz MHz
10
Page 11
Wistron
NeWeb
PARAMETER CONDITIONS MIN TYP MAX UNIT
Frequency Error 16MHz crystal
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
+/- 20 ppm
Wistron NeWeb Confidential Document
11
Page 12
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
6.6. Electrical Characteristics – End-to-end Audio Characteristics
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-6 -7 AVMD7540-SWA6 Electrical Characteristics – End-to-end Audio Characteristics
PARAMETER CONDITIONS MIN TYP MAX UNITS
End-to-end SNR I2S in to I2S out, no interference;
16bit / 48kHz mode 24bit / 48kHz mode 16bit / 96kHz mode 24bit / 96kHz mode
Latency 48kHz, interleaving level = 0
48kHz, interleaving level = 1 48kHz, interleaving level = 2
Bandwidth +/-0.5dB flatness, 48Khz modes
+/-0.5dB flatness, 96Khz modes
96
120
97
120
11
20 20
20k
15 19
40k
dB dB dB
dB ms ms ms
Hz
Hz
6.7. Electrical Characteristics – MCLK Characteristics
Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA6 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.
Table 6-7 AVMD7540-SWA6 Electrical Characteristics – MCLK Characteristics
PARAMETER CONDITIONS MIN TYP MAX UNITS
MCLK frequency
MCLK output duty cycle 40 60 %
“24MHz” mode (256MHz divide by 10.5) “12MHz” mode (256MHz divide by 21)
24.38
12.19
MHz MHz
Wistron NeWeb Confidential Document
12
Page 13
Wistron
NeWeb
®
Wistron NeWeb Corporation
20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.
Phone: 886-3-666-7799 Fax: 886-3-666-7711
7. Package Information
Wistron NeWeb Confidential Document
13
Loading...