Wistron NeWeb SWA5 User Manual

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

Product Specification

Model Name: AVMD7540-SWA5

(AV7540 +16dBm module with U.FL connector)

Revision: 1.0

Issue Date: 2010/10/26

This document and the information contained herein is the property of Wistron NeWeb Corporation and reproduction by any means (including, but not limited to, xerographic, chemical, electronic) and distribution is expressly prohibited without prior written consent from Wistron NeWeb Corporation. The document and information contained herein are confidential and may not be divulged without express written consent from Wistron NeWeb Corporation, located at 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Wistron NeWeb Confidential Document

1

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

Wistron NeWeb Confidential Document

2

Wistron

Website: www.wneweb.com

1.0 Add FCC certification wording on p.3

2010/10/26

Amy

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

Revision History

Edition #

0.1 Initial Revision 2010/05/07

Reason for revision Issue date Author

cjo

Wistron NeWeb Confidential Document

3

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

1. General Description

The AVMD7540-SWA5 module is a complete radio module solution containing all the necessary HW and FW to provide a system-integration ready, multichannel wireless HD audio solution.

The module is comprised of a AV7540 IC combined with RF front-end circuits (RF PA + balun + filter + RF switch), flash memory, crystal, and passive components. It is FCC certified and ready for operation with U.FL connectors. The module provides a convenient set of digital I/O interfaces for digital audio through an I2S port, host MCU control through an SPI or I2C interface and optional GPIO for various control and indicator functions.

The module is a card edge style using the 36 pin PCIe card edge connection method to save space and cost in connecting to the main board.

FCC & IC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS

102.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102

Wistron NeWeb Confidential Document

4

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

2. Features

 Complete, Integrated Wireless Module

o AV7540 IC o RF front-end o Flash memory

 High Performance Audio and RF solution

o 16 bit, 48kHz to 24 bit, 96kHz digital audio o 120dB SNR Digital Audio Path o Fixed Low Latency solution o +16dBm transmit RF output power o -82dBm receive RF sensitivity o Support for 30m/100m range NLOS/LOS

 Digital interfaces and Audio

o 8 channel digital audio I/O (4 I2S ports)

 Configurable as input or output

o Stereo audio DAC output o 4-wire SPI slave interface or 2-wire I2C-compatible communication with the host MCU

 Package and connections

o Compact size o 36 pin (2x18) PCIe card edge connector o diversity antenna capability

Wistron NeWeb Confidential Document

5

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

3. Block Diagram

3. Module Outline

Wistron NeWeb Confidential Document

6

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

4. Pin Configuration and Definition

Figure 1-1 – AVMD7540-SWA5 module pin configuration

Wistron NeWeb Confidential Document

7

Wistron

Website: www.wneweb.com

NeWeb

Table !                -1 AVMD7540-SWA5 pin description

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

# Pin Name Pin Type Description

A1 GND Analog Module ground A2 GND Analog Module ground A3 WCLK2 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 2 – input/output A4 BCLK2 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 2 – input/output A5 ADAT2 Digital I/O I2S audio data, AV75xx physical I2S I/O #2 – input/output A6 WCLK0 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 0 – input/output A7 BCLK0 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 0 – input/output A8 ADAT0 Digital I/O I2S audio data, AV75xx physical I2S I/O # 0 – input/output A9 SPI/TWI_SEL Digital I/O SPI / TWI interface selection (SPI = 0, TWI = 1) A10 GPIO6 Digital I/O GPIO #6

A11 GPIO4 Digital I/O GPIO #4

A12 GPIO3 Digital I/O GPIO #3

A13 GPIO5 Digital I/O GPIO #5

A14 reserved Digital I/O reserved

A15 AGND Analog Audio ground

A16 ROUT Analog Audio DAC right channel output

A17 LOUT Analog Audio DAC left channel output

A18 AGND Analog Audio ground

B1 VCC Analog +5V supply voltage input B2 VCC Analog +5V supply voltage input B3 ADAT3 Digital I/O I2S audio data, AV75xx physical I2S I/O # 3 – input/output B4 BCLK3 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 3 – input/output B5 WCLK3 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 3 – input/output B6 MCLK_OUT Digital Output MCLK for I2S audio data B7 ADAT1 Digital I/O I2S audio data, AV75xx physical I2S I/O # 1 – input/output B8 BCLK1 Digital I/O I2S Bit clock, AV75xx physical I2S I/O # 1 – input/output B9 WCLK1 Digital I/O I2S Word clock, AV75xx physical I2S I/O # 1 – input/output B10 SDA Digital I/O I2C compatible serial data I/O

B11 SCL Digital I/O I2C compatible serial clock I/O

B12 S_SSB Digital I/O SPI Slave – slave select (active low)

B13 S_SCLK Digital I/O SPI Slave – serial clock

Wistron NeWeb Confidential Document

8

Wistron

Website: www.wneweb.com

NeWeb

# Pin Name Pin Type Description

B14 S_MOSI Digital I/O SPI Slave – master out slave in

B15 S_MISO Digital I/O SPI Slave – master in slave out

B16 SRQ/PND Digital Output Notification signal to host (pending notification)

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

B17 SM0 Digital Input

B18 WM_DETN Digital output Wireless module detect (low signal to indicate module is inserted in

Serial Mux control (for flash programming) and module reset (active low)

product)

Wistron NeWeb Confidential Document

9

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

5. Electrical Specifications

5.1. Absolute Maximum Ratings

The Absolute Maximum Rating (AMR) corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified.

Table 6-1 6-2 AVMD7540-SWA5 Absolute Maximum Ratings

CONDITION MIN MAX Units

Supply (relative to GND) +5V -0.3 6.0 V

Input Voltage Range – Digital Inputs -0.3 3.6V V Short circuit to GND (any pin) --- continuous Storage Temperature -40 +100 ºC Lead Temperature (10s) -- +225 ºC ESD Voltage Rating – Human Body Model test 2000 V

Wistron NeWeb Confidential Document

10

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

5.2. DC Electrical Characteristics

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-2 6-3 AVMD7540-SWA5 DC Electrical Characteristics

PARAMETER CONDITIONS MIN TYP MAX UNIT

Input supply voltage Driven by an external regulator 4.5 5.5 V

Supply Current – (Note 1) RESET 10 mA RX mode: 1 stereo output I2S 100 mA

CMOS I/O Logic Levels – 3.3V I/O

Input Voltage Logic Low, VIL Internal regulator = 3.3V 0.6 V Input Voltage Logic High, VIH Internal regulator = 3.3V 2.0 V Output Voltage Logic Low, VOL Internal regulator = 3.3V; I Output Voltage Logic High, VOH Internal regulator = 3.3V; I

Note 1: The operating states are defined as: RESET = AVMD7540-SWA5 is held in reset by holding SM0 low RX mode: AVMD7540-SWA5 is operating in a link as a client node receiving 1 stereo channel of 16bit,

48kHz audio.

=1mA 0.4 V

LOAD

=1mA 2.9 V

LOAD

5.3. Electrical Characteristics – RF Receiver

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-3 -4 AVMD7540-SWA5 Electrical Characteristics – RF Receiver

PARAMETER CONDITIONS MIN TYP MAX UNIT

RF Channel Frequency Range 2412 2462 MHz Sensitivity (Note 1) TA=25ºC -80 dBm Max Input Signal (Note 1) -5 dBm

2400-2483.5 MHz

Spurious RF outputs

LO leakage -47 dBm

Note 1: Sensitivity and max signal level are defined as the onset of 1% BLER Block Error Rate.

<2400 MHz >2483.5 MHz

-47

-60

dBm dBm dBm

Wistron NeWeb Confidential Document

11

Wistron

Website: www.wneweb.com

®

NeWeb

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

5.4. Electrical Characteristics – RF Transmitter

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-5 -5 AVMD7540-SWA5 Electrical Characteristics – RF Transmitter

PARAMETER CONDITIONS MIN TYP MAX UNIT

RF Performance

RF Channel Frequency Range 2412 2462 MHz Output Power TA=25ºC, OFDM signal, 16MHz channel BW +16 dBm Harmonics (Note 1) 2nd harmonic

Conducted RF Spurious signals 800-1000MHz

Radiated Spurious RF signals 30-88MHz,

LO leakage Relative to power in a 100kHz BW **, after DC

Note 1: Measured at TX output power = +16dBm Note 1: Measured at TX output power = +16dBm

3rd harmonic

2000-2390MHz

2483.5- 3000MHz; RBW=1MHz 3000-4000MHz ; RBW=1MHz

4.0-26.5GHz; RBW=1MHz

88-216MHz 216-960MHz >960MHz

offset correction

-45

34

37 40 48

-20 dBc

dBm dBm dBm dBm dBm

dBuV/

m

5.5. Electrical Characteristics – RF Channel Frequency

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-5 -6 AVMD7540-SWA5 Electrical Characteristics – RF Transmitter

PARAMETER CONDITIONS MIN TYP MAX UNIT

RF Performance

Channel Frequency

Wistron NeWeb Confidential Document

AM2G system channel 1 AM2G system channel 2 AM2G system channel 3

2412 2438 2462

MHz MHz MHz

12

Wistron

Website: www.wneweb.com

NeWeb

PARAMETER CONDITIONS MIN TYP MAX UNIT

Frequency Error 16MHz crystal

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

+/- 20 ppm

Wistron NeWeb Confidential Document

13

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

5.6. Electrical Characteristics – End-to-end Audio Characteristics

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-6 -7 AVMD7540-SWA5 Electrical Characteristics – End-to-end Audio Characteristics

PARAMETER CONDITIONS MIN TYP MAX UNITS

End-to-end SNR I2S in to I2S out, no interference;

16bit / 48kHz mode 24bit / 48kHz mode 16bit / 96kHz mode 24bit / 96kHz mode

Latency 48kHz, interleaving level = 0

48kHz, interleaving level = 1 48kHz, interleaving level = 2

Bandwidth +/-0.5dB flatness, 48Khz modes

+/-0.5dB flatness, 96Khz modes

96

120

97

120

11

20 20

20k

15 19

40k

dB dB dB dB ms ms ms Hz Hz

5.7. Electrical Characteristics – MCLK Characteristics

Operating Conditions: +5V_IN = 5.0V ±10%, TA=0ºC to +50 ºC; RF Chan. Freq. = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7540-SWA5 edge connector pins and RF connectors, unless otherwise specified. Typical specifications at 5.0V and 25 ºC.

Table 6-7 cccccccccccvcccccccccccccccccccccc-8 AVMD7540-SWA5 Electrical Characteristics – MCLK Characteristics

PARAMETER CONDITIONS MIN TYP MAX UNITS

MCLK frequency

MCLK output duty cycle 40 60 %

“24MHz” mode (256MHz divide by 10.5) “12MHz” mode (256MHz divide by 21)

24.38

12.19

MHz MHz

Wistron NeWeb Confidential Document

14

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

6. Mechanical Dimension

Wistron NeWeb Confidential Document

15

Wistron

Website: www.wneweb.com

NeWeb

®

Wistron NeWeb Corporation

20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C.

Phone: 886-3-666-7799 Fax: 886-3-666-7711

7. Package Information

50pcs / Tray-Plate

40 Tray-Plate / Carton -> 2000pcs / Carton

Wistron NeWeb Confidential Document

16

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

IMPORTANT NOTE: FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKR-SWA5". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.