Wistron NeWeb RM1 Users manual

WLAN b+g mini-PCI Module

RM1

OEM Installation Manual

(The module is sold only to the OEM integrators & the

manual is valid only for the OEM manufactures)

Version: 1.0

June 2004

Copyright Statement

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording or otherwise without the prior writing of the publisher.
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp.
Pentium is trademark of Intel.
All copyright reserved.

1

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded
interface cables when connecting to computer or peripheral devices) any
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference

that may cause undesired operation.

IMPORTANT NOTE:

This module is restricted to mobile configuration. To comply with FCC RF exposure
compliance requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter. This

transmitter module must not be co-located or operating in conjunction with any

other antenna or transmitter

2

Table of Contents

Table of Contents.................................3

1. Introduction..................................... 4

1.1 The WLAN 802.11b+g mini-PCI Module 4

1.2 Hardware Installation & Antenna Information 4

*Caution !!........................................... 6

(1). This module cannot be bound in a tablet computer for RF exposure issues. (See label 1)6
(3). This module must be labeled with FCC ID. (See label 2) 6

(4). If the FCC ID is not visible when the module is installed inside another device, then the outside of
device must also display a label referring to the enclosed module. The exterior label can be “ Contains

Transmitter Module FCC ID:NKRRM1 ” or similar wording. (See label 3) 7

2. Features.......................................... 8

3. Hardware Connections....................... 9

4. Remove the Module .........................11

5. Basic Configuration of your Access Point12

5.1 Logging On ..............................13

5.2 Setup Wizard............................13

l 5.2.1 SETTING UP LOCAL TIME ZONE AND DATE/TIME 13
l 5.2.2 DEVICE IP SETTINGS13
l 5.2.2 DEVICE IP SETTINGS14
l 5.2.3 CONFIGURE YOUR WIRELESS LAN CONNECTION 15
l 5.2.4 FINISH SETUP WIZARD AND SAVE YOUR SETTINGS 16

3

1. Introduction

1.1 The WLAN 802.11b+g mini-PCI Module

Thank you for purchasing the WLAN b+g mini-PCI Module that provides the easiest
way to wireless networking. This User Manual contains detailed instructions in the
operation of this product. Please keep this manual for future reference.

SYSTEM REQUIREMENTS

l Microsoft® Win™2000/ME/98 Second Edition/XP

1.2 Hardware Installation & Antenna Information

l MODULE IS INSTALLED IN THE ROUTER. (SEE THE FOLLOWING DIAGRAMS).

4

l Antennas are embedded in the two sides (see the two antennas shown

below)

Aux

Main

Only the antenna type listed below can be used:
(1) Vendor WanShih Electronic CO. Model: Wss002

Important Note:

This module is restricted to mobile configuration. The antennas of module
should be installed and operated with minimum distance 20cm between the
radiator and all persons. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

The module is for OEM installation only and can not be sold to end user directly.

5