Wistron NeWeb P68 Users manual

Wireless Module

Model : DHUR-P68

User Manual

Panasonic

Copyright Statement

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, whether electronic, mechanical, photocopying, recording or otherwise
without the prior writing of the publisher.
Pentium is trademark of Intel.
All copyright reserved.

1

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

IMPORTANT NOTE:
Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

Country Code selection feature to be disabled for products marketed to the US/CANADA

Operation of this device is restricted to indoor use only

2

Integration instructions for host product manufacturers

Applicable FCC rules to module

FCC Part 15.247

Summarize the specific operational use conditions

The module is must be installed in mobile device.
This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna

3) For all products market in US, OEM has to limit the operation channels in CH1 to
CH11 for 2.4G band

by supplied firmware programming tool. OEM shall not supply any tool or info to the

end-user regarding

to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.

Limited module procedures

Not applicable

Trace antenna designs

Not applicable

RF exposure considerations

20 cm separation distance and co-located issue shall be met as mentioned in
“Summarize the specific operational use conditions”.
Product manufacturer shall provide below text in end-product manual

“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.”

3

Antennas

Brand name

Model name

Antenna type

Antenna
connector

NA

ANT0

PIFA

NA

NA

ANT1

PIFA

NA

Label and Compliance Information

Product manufacturers need to provide a physical or e-label stating
“Contains FCC ID: NKR-P68” with finished product

Information on Test Modes and Additional Testing Requirements

Test tool: MT7668 QA, Version: 0.0.1.98 shall be used to set the module to transmit
continuously.

Additional Testing, Part 15 Subpart B Disclaimer

The module is only FCC authorized for the specific rule parts listed on the grant, and that
the host product manufacturer is responsible for compliance to any other FCC rules that
apply to the host not covered by the modular transmitter grant of certification. The final
host product still requires Part 15 Subpart B compliance testing with the modular
transmitter installed

4

Industry Canada statement:

Brand name

Model name

Antenna type

Antenna
connector

NA

ANT0

PIFA

NA

NA

ANT1

PIFA

NA

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:

(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause
undesired operation of the device

Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes
au (x) RSS (s) exemptés de licence d'Innovation, Sciences et Développement
économique Canada. L'opération est soumise aux deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interférences
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant
provoquer un fonctionnement indésirable de l'appareil

This radio transmitter (IC: 4441A-P68) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 4441A-P68) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

5

Caution:

(i) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;

(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;

(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate; and

Operations in the 5.25-5.35GHz band are restricted to indoor usage only.

Avertissement:

(i) les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
pour les dispositifs utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725 MHz doit
être conforme à la limite de la p.i.r.e;

(iii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
(pour les dispositifs utilisant la bande de 5725 à 5850 MHz) doit être conforme à la limite
de la p.i.r.e. spécifiée pour l'exploitation point à point et l'exploitation non point à point,
selon le cas;

Les opérations dans la bande de 5.25-5.35GHz sont limités à un usage intérieur
seulement.

Radiation Exposure Statement:

6

This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme Canada limites d'exposition aux radiations dans un
environnement non contrôlé. Cet équipement doit être installé et utilisé à distance
minimum de 20cm entre le radiateur et votre corps.

This device is intended only for OEM integrators under the following conditions:

1) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 1 condition above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:

1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization is
no longer considered valid and the IC number can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation

7

distincte au Canada.

End Product Labeling

The final end product must be labeled in a visible area with the following: “Contains IC:
4441A-P68”.

Plaque signalétique du produit final

Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 4441A-P68".

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.

8

Europe – EU Declaration of Conformity

BE

BG

CZ

DK

DE

EE

IE

EL

ES

FR

HR

IT

CY

LV

LT

LU

HU

MT

NL

AT

PL

PT

RO

SI

SK

FI

SE

UK

LI

IS

NO

TR

CH

This device complies with the essential requirements of the Radio Equipment directive: 2014 / 53
/ EU. The following test methods have been applied in order to prove presumption of conformity
with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU:

EN 300 328 V2.2.2
EN 301 893 V2.1.1
EN 50665:2017
EN 62311:2008
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
IEC 62368-1:2014; and/or
EN 62368-1:2014+A11:2017

19.87 dBm, 2412-2472MHz (Wi Fi)

4.60 dBm, 2402-2480MHz (BT EDR)

3.10 dBm, 2402-2480MHz (BT LE)

16.84 dBm, 5150-5250MHz

19.71 dBm, 5250-5350MHz

19.70 dBm, 5470-5725MHz
SW version: 1.0

The minimum distance between the user and/or any bystander and the radiating structure of the
transmitter is 20cm.
5150 ~ 5350 MHz is limited to indoor used in below countries.

9

端末機器の技術基準設計認証の認定番号
本製品は以下に認証を受けたものです。
認証機器名：DHUR-P68
認定番号： R 201-XXXXXX

Taiwan 警語

 第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不

得擅自變更頻率、加大功率或變更原設計之特性及功能。

 第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾

現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工
業、科學及醫療用電波輻射性電機設備之干擾。

 無線資訊傳輸設備避免影響附近雷達系統之操作。

 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平台

上標示「本產品內含射頻模組:

CCAFXXLPXXXXTX」字樣.

10

Table of Contents

1. INTRODUCTION

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION

3. CONNECTING TO AN EXISTING NETWORK

4. MODIFYING A WIRELESS NETWORK

4.1 MODIFYING GENERAL SETTINGS ................................................................................................

4.2 MODIFYING SECURITY SETTINGS ................................................................................................

5. Product Specifications

11

1. INTRODUCTION

DHUR-P68 is a 802.11 a/b/g/n /ac and Bluetooth Combo module that provides the easiest way to
wireless networking. This User Manual contains detailed instructions in the operation of this
product. Please keep this manual for future reference.

System Requirements

- 128 MB of RAM or later (recommended)

- 300 MHz processor or higher

2. Driver/Utility Installation

The driver should have been installed before the TV is shipped from the manufacturer. You can
start using its network function without installing driver or utility.

3. Connecting to an Existing Network

1. Use the remote control that came with your TV to access the network configuration settings

page.

2. Select the scanning wireless network function. The system starts to scan for available network.

On this list, click Refresh to refresh the list at any time

3. Select the network you want to connect to.

4. If the chosen network has security enabled, you will have to setup corresponding security

parameter. Contact the network manager for the correct settings. Select the security type and
fill in required parameters. The options include the following:

 WPA/WPA2/CCKM
 WPA/WPA2 Passphrase
 802.1x
 Pre-Shared Key (Static WEP)
 None

12

4. Modifying a Wireless Network

Profile Name

Identifies the configuration wireless network profile.
This name must be unique. Profile names are not
case sensitive.

Client Name

Identifies the client machine.

Use this profile for

Access Point mode

Configures station to operate in Access Point mode.

Network Names

(SSIDs)

The IEEE 802.11 wireless network name. This field
has a maximum limit of 32 characters. Configure up
to three SSIDs (SSID1, SSID2, and SSID3).

4.1 Modifying General Settings

1. Use the remote control that came with your TV to access the network configuration settings

page.

2. From the profile list, select one profile and choose the modify function.

3. Modify the settings below for your network.

13

4.2 Modifying Security Settings

WPA/WPA2

Enables the use of Wi-Fi Protected Access (WPA).
Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu.
The options include:

 EAP-FAST
 EAP-TLS
 EAP-TTLS
 EAP-SIM
 PEAP (EAP-GTC)
 PEAP (EAP-MSCHAP V2)
 LEAP

WPA/WPA2
Passphrase

Enables WPA/WPA2 Passphrase security.
Click on the Configure button and fill in the WPA/WPA2 Passphrase.

802.1x

Enables 802.1x security. This option requires IT administration.
Choosing 802.1x opens the 802.1x EAP type drop-down menu. The
options include:

 EAP-FAST
 EAP-TLS
 EAP-TTLS
 EAP-SIM
 PEAP (EAP-GTC)
 PEAP (EAP-MSCHAP V2)
 LEAP

Pre-Shared Key
(Static WEP)

Enables the use of pre-shared keys that are defined on both the access
point and the station.
To define pre-shared encryption keys, choose the Pre-Shared Key radio
button and click the Configure button to fill in the Define Pre-Shared
Keys window.

1. Use the remote control that came with your TV to access the network configuration settings

page.

2. Select a security option of this wireless network. This product provides security options below.

Contact your wireless network administrator for choosing a correct option.

 WPA/WPA2/CCKM
 WPA/WPA2 Passphrase
 802.1x
 Pre-Shared Key (Static WEP)
 None

14

None

No security (not recommended).

Allow Association to
Mixed Cells

Check this check box if the access point with which the client adapter is
to associate has WEP set to Optional and WEP is enabled on the client
adapter. Otherwise, the client is unable to establish a connection with
the access point.

Limit Time for
Finding Domain
Controller To

Check this check box and enter the number of seconds (up to 300) after
which the authentication process times out when trying to find the
domain controller. Entering zero is like unchecking this check box,
which means no time limit is imposed for finding the domain controller.
Note: The authentication process times out whenever the authentication
timer times out or the time for finding the domain controller is reached.

Group Policy Delay

Specify how much time elapses before the Windows logon process
starts group policy. Group policy is a Windows feature used by
administrators to specify configuration options for groups of users. The
objective is to delay the start of Group Policy until wireless network
authentication occurs. Valid ranges are from 0 to 65535 seconds. The
value that you set goes into effect after you reboot your computer with
this profile set as the active profile.
This drop-down menu is active only if you chose EAP-based
authentication.

15

5. Product Specifications

Item

Content

Frequency
range

BT: 2402~2480MHz
WLAN:

2412~2472MHz

5.15~5.25GHz

5.25~5.35GHz

5.470~5.725GHz

5.725~5.850GHz

Channel
spacing

BT/BLE: 1MHz/2MHz
WLAN:
5MHz for 2.4G
20MHz for 5.0G

Modulation
technology

BT: GFSK, π/4 – DQPSK, 8DPSK

WLAN : DSSS : CCK,DQPSK,DBPSK

OFDM :BPSK,QPSK,16QAM,64QAM,256QAM

Data Rate

BT: 1/2/3Mbps, BLE: 1Mbps

802.11b: 11/5.5/2/1Mbps

802.11g: 54/48/36/24/18/12/9/6Mbps

802.11a: 54/48/36/24/18/12/9/6Mbps

802.11n:
20MHz: MCS0~MCS15
40MHz: MCS0~MCS15

802.11ac
VHT20: MCS0~MCS9
VHT40: MCS0~MCS9
VHT80: MCS0~MCS9

Host
interface

USB 2.0

Operation
voltage

5V
Operation

0o ~ 60oC

Product Name：Wireless Module
Brand Name：Panasonic
Model Name：DHUR-P68

16

temperature

Antenna
Type

PIFA

Antenna
gain

6. Pin assignment