Wistron NeWeb IDA201 User Manual

FHD251E IP Camera

User Manual

Table of Contents

FCC STATEMENT ............................................................................... 1

SAFETY PRECAUTIONS ..................................................................... 3

1 INTRODUCTION ...................................................................... 5

1.1 PACKAGE CONTENTS ............................................................... 5

1.2 KEY FEATURES ....................................................................... 6

1.3 HARDWARE OVERVIEW ........................................................... 7

2 START USING THE CAMERA .................................................. 11

2.1 ASSEMBLING THE CAMERA & THE WIRELESS ADAPTER ................ 11

2.2 CONNECTING THE CAMERA TO A NETWORK............................... 14

2.3 REBOOTING AND RESETTING THE CAMERA ................................ 15

3 APPENDIX ............................................................................. 16

3.1 SPECIFICATIONS AND COMPLIANCE .......................................... 16

3.2 TROUBLESHOOTING .............................................................. 18

3.3 OBTAINING TECHNICAL SUPPORT ............................................ 19

3.4 DISPOSAL INSTRUCTIONS ....................................................... 19

FCC Statement

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for
help.

1

FCC Radiation Statement

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority
to operate this equipment.

This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20 cm between the
radiator & your body.

2

Safety Precautions

Please read this user manual before operating this product. The
information contained in this document is subject to change without
notice. Features or specifications may be different depending on the
type of product model purchased.

Safe Use of This Product

Carefully follow the warnings and safety notices presented within this
manual. Please pay special attention to the following indications of
potentially hazardous situations:

Warning: Indicates a hazardous situation, which, if not avoided, could
result in serious injury.
Caution: Indicates a situation, which, if not avoided, could damage
this product or other devices.
Note: Indicates additional user information to make the user aware
of possible problems and to help the user understand, use, and
maintain the product.

3

•

This product needs only an occasional wipe with a dry cloth.

•

Avoid high-moisture conditions and keep away from liquids and
humidity.

•

Do not install or use the product where it is exposed to direct
sunlight or heat.

•

Care must be taken when using the device in close proximity to
personal medical devices, such as pacemakers and hearing aids.

•

Do not use this product in environments where there are
potential explosion hazards.

•

The product must be placed horizontally on a hard, flat surface
or installed firmly with wall-mount kits. Do not place the
product where it may be subject to physical shock or vibration
or where the product may drop, topple, slide, or shake; this
may cause personal injury or damage to the product.

•

If lightning is expected, or the product is not going to be used
for a long period of time, unplug the power cord from the unit.

•

The use of electronic transmitting devices in aircraft, hospitals,
and petrol stations is forbidden. Please follow the rules and
warnings in these conditions.

•

The product must ONLY be used with the power supply cord
and power adapter supplied by the manufacturer.

•

Openings on the housing of the product are required for
ventilation. Do not block or obstruct the air flow through these
openings.

•

Do not operate the product on a soft surface such as carpet,

rug, bed, etc.

4

1 Introduction

1.1 Package Contents

Thank you for purchasing this product. Before using the FHD251E
IP Camera (referred to in this manual as “the camera”), please
confirm that the packaging includes the following items and
accessories:

 FHD251E IP Camera
 WFB100S Wireless Power over Ethernet (PoE) Adapter (referred

to in this manual as “the wireless adapter”)

 Camera bracket & screws
 User manual

5

1.2 Key Features

FHD251E

• Full HD 1080p @ 30 fps (1920 × 1080)

• Visualization in total darkness up to 15 meters

• Switchable IR cut filter for vivid color during the daytime

• Light sensor to automatically detect ambient light conditions

• Motion detection

• Digital PTZ

• HDR

• LDC

• Power over Ethernet

• Waterproof IP65

• Easily connects to home-network environments

WFB100S

• Internal Power Module, V-in: 120 V, V-out: 48 V

• Wi-Fi: 2.4 GHz IEEE 802.11n 2 × 2

• RJ45 Ethernet connection

• IEEE 802.3af–compliant

• WPS for easy network pairing

6

1.3 Hardware Overview

Cap

Light guide
Status LED

Cap

Speaker

Microphone

Ball joint
IR lens

FHD251E

Front view

Rear view

7

LED functions

LED Color

Function Description

Status

Red

Pre-boot

Solid on if “power OK”

Blue

Operating system
booting

Blinking 1 Hz, 50% duty
cycle

Green

Post-boot; no network
connectivity

Blinking 4 Hz, 50% duty
cycle

Green

Standby; encoder
recording locally

Solid on

Green

Streaming to the
network

Blinking 1 Hz, 50% duty
cycle

8

LED color

Function description

Status

Blue

Normal operation and
connected

Solid on

Blue

Power up and during
firmware download

Fast blinking, 4 Hz, 50%
duty cycle

Blue

Firmware download
complete but no
connectivity

Slow blinking, 1 Hz, 50%
duty cycle
Blue

WPS mode activated

Off

Light guide
Button

Ethernet port

LED functions:

WFB100S

9

10

2 Start Using the Camera

2.1 Assembling the Camera & the Wireless

Adapter

Follow the steps below to set up your camera hardware and ensure
that the camera operates properly.

1. Attach the camera bracket to the camera by gently tightening it

onto the camera.

Caution:
Ensure that the camera is securely fixed;
otherwise it may fall and cause damage
or injury.

11

2. Remove the grommet and the cap on the rear side of the

camera.

3. Insert the Ethernet cable into the camera’s Ethernet port and

connect the other end to the wireless adapter, then place the
grommet back and screw on the cap.

12

4. Plug the wireless adapter into an electrical outlet.

13

2.2 Connecting the Camera to a Network

1. After inserting the Ethernet cable into the camera’s Ethernet

port and connecting the other end to the wireless adapter, the
adapter will be able to supply power to the camera when
plugged into a wall outlet.

2. Press the WPS button of the AP that you want to connect to,

then press the adapter’s button to connect to the AP. Once the
Wi-Fi of the wireless adapter is paired with an AP via WPS, the
camera then connects to the network through the wireless
adapter.

3. The IP camera has been successfully added to your network after

the connection between the wireless adapter and your AP is
established.

The installation process is now complete. Now you may start using
the camera.

14

2.3 Rebooting and Resetting the Camera

and the Wireless Adapter

1. Press and hold the button on the wireless adapter for 0

seconds–3 seconds or over 20 seconds.

2. For factory reset, press and hold the button on the wireless

adapter for 10 seconds–20 seconds.

15

3 Appendix

Model

FHD251E

Resolution

1080p (1920 × 1080) @ 30 fps

IR LEDs

12 pcs.

IR LED Illumination Range

15 meters

Sensitivity

0 lux when IR LED is on (black & white video).

Sensors

CMOS 1/3” 4 megapixels

Lens

6 glass

Status LEDs

1 pc (Tri color—red, blue, and green)

FOV

138° (D)

Operating Voltage

V-in: 48 V (DC)

Ambient Operating
Temperature

–40 °C to +65 °C
Storage Temperature

–40 °C to +65 °C

Dimensions

77.05 mm × 115.97 mm × 79.2 mm

Weight

324 g

IP Rating

IP65

PoE

IEEE 802.3af

3.1 Specifications and Compliance

16

Model

WFB100S

CPU

RTL8196E

2.4 GHz

RTL8192ER

SPI Flash Memory

32 MB

DDR3

128 MB

Status LEDs

1 pc (Single color—blue)

RJ45

10/100 mbps

Operating Voltage

V-in: 120 V (AC), V-out : 48 V (DC)

Ambient Operating
Temperature

0 °C to +50 °C
Storage Temperature

–40 °C to +65 °C

Dimensions

91 mm × 57 mm × 44 mm

Weight

124 g

17

3.2 Troubleshooting

Problem

Solution

The button
has no
response.

1. Check the Ethernet connection status.

2. Plug out and plug in once to reboot the
wireless adapter.

The LED blinks
slowly after
the WPS
process is
completed.

1. Check the Ethernet connection status.

2. Restart WPS pairing and make sure the AP
router is in signal range and is in WPS mode.

18

3.3 Obtaining Technical Support

While we hope your experience with the FHD251E IP Camera is
enjoyable, you may experience some issues or have questions that
this User Manual has not answered.
If you have a problem with the FHD251E IP Camera, please contact us
at:

Tel.:[phone] Ext.: 3214
E-mail: [e-mail]
Mobile: [phone]
Website: www.wnc.com.tw

3.4 Disposal Instructions

WNC is committed to responsible environmental stewardship. Please
dispose of this product in accordance with the local laws and
regulations in your area. Contact your local waste-disposal
authorities for relevant instructions.

19