Wistron NeWeb DNUR-S2 User Manual
802.11abgn 2x2 USB WiFi module
DNUR-S2
User Manual
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, whether electronic, mechanical, photocopying, recording or otherwise
without the prior writing of the publisher.
Pentium is trademark of Intel.
All copyright reserved.
1
Ta ble of Conte nts
1. INTRODUCTION 2
2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 2
3. CONNECTING TO AN EXISTING NETWORK 2
4. MODIFYING A WIRELESS NETWORK 3
4.1
M
ODIFYING GENERAL
SETTINGS ............................................................................................. 3
4.2
M
ODIFYING SECURITY SETTINGS
5. SPECIFICATIONS 5
............................................................................................ 4
APPENDIX A: FAQ ABOUT WLAN 6
2
1. Introduction
Thank you for purchasing the WLAN 802.11 a/b/g/n USB Module that provides the easiest way
to wireless networking. This User Manual contains detailed instructions in the operation of this
product. Please keep this manual for future reference.
System Requirements
- 128 MB of RAM or later (recommended)
2. Driver/Utility Installation
- 300 MHz processor or higher
The driver should have been installed before the Blueray player is shipped from the manufacturer.
You can start using its network function without installing driver or utility.
3. Connecting to an Existing Network
1. Use the remote control that came with your Blueray player to access the network
configuration settings page.
2. Select the scanning wireless network function. The system starts to scan for available network.
On this list, click Refresh to refresh the list at any time
3. Select the network you want to connect to.
4. If the chosen network has security enabled, you will have to setup corresponding security
parameter. Contact the network manager for the correct settings. Select the security type and
fill in required parameters. The options include the following:
•
WPA/WPA2/CCKM
•
WPA/WPA2 Passphrase
•
802.1x
•
Pre-Shared Key (Static WEP)
•
None
3
4. Modifying a Wireless Network
4.1 Modifying General Settings
1. Use the remote control that came with your Blueray player to access the network
configuration settings page.
2. From the profile list, select one profile and choose the modify function.
3. Modify the settings below for your network.
Profile Name
Identifies
the
configuration wireless network
profile.
Client Name
Use this profile for
Access Point mode
Network Names
(SSIDs)
This name must
be
unique. Profile names
are not case
sensitive.
Identifies
Configures station
the
client
machine.
to
operate
in
Access Point
mode.
The IEEE 802.11 wireless network name. This field
a
maximum limit
SSIDs (SSID1, SSID2, and
of 32
characters. Configure
SSID3).
up to three
has
4.2 Modifying
WPA/WPA2
Enables the use of Wi-Fi Protected Access (WPA).
LEAP
WPA/WPA2
Enables WPA/WPA2 Passphrase security.
802.1x
Enables 802.1x security. This option requires IT administration.
Pre-Shared Key
Enables the use of pre-shared keys that are defined on both the access
Security
Settings
1. Use the remote control that came with your Blueray player to access the network
configuration settings page.
2. Select a security option of this wireless network. This product provides security options below.
Contact your wireless network administrator for choosing a correct option.
•
WPA/WPA2/CCKM
•
WPA/WPA2 Passphrase
•
802.1x
•
Pre-Shared Key (Static WEP)
•
None
Passphrase
Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu.
The options include:
EAP-FAST
EAP-TLS
EAP-TTLS
EAP-SIM
PEAP (EAP-GTC)
PEAP (EAP-MSCHAP V2)
Click on the Configure button and fill in the WPA/WPA2 Passphrase.
Choosing 802.1x opens the 802.1x EAP type drop-down menu. The
options include:
EAP-FAST
EAP-TLS
EAP-TTLS
EAP-SIM
PEAP (EAP-GTC)
PEAP (EAP-MSCHAP V2)
LEAP
(Static WEP)
point and the station.
To define pre-shared encryption keys, choose the Pre-Shared Key radio
button and click the Configure button to fill in the Define Pre-Shared
Keys window.
4
Loading...