Wistron NeWeb DNMA-92 User Manual

WLAN a/b/g/n mini-PCI Module

DNMA-92 User Manual

Version: 1.0

April 2009

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is trademark of Intel.

All copyright reserved.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only.

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKR-DNMA-92 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Table of Contents

1. INTRODUCTION 5

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 6

2.1 INSTALLATION..........................................................................................................6

2.2 ADDITIONAL SETUP PROCESSES..............................................................................9

2.3 UNINSTALLATION...................................................................................................10

3. CONNECTING TO AN EXISTING NETWORK 11

4. CREATING AN AD HOC NEW NETWORK 16

5. MODIFYING A WIRELESS NETWORK 20

5.1 INFRASTRUCTURE MODE AND AD HOC MODE .....................................................20

5.2 MODIFYING A WIRELESS NETWORK.....................................................................21

5.3 DEF AULT SETTINGS WINDOWS XP ZERO-CONFIGURATION................................28

5.4 SUPER A/G SETTING ...........................................................錯誤! 尚未定義書籤。

APPENDIX A: F AQ ABOUT WLAN 29

APPENDIX B: SPECIFICATION 31

1. Introduction

Thank you for purchasing the WLAN a/b/g/n mini-PCI Module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference.

System Requirements

z A laptop PC contains:

- 32 MB memory or greater

- 300 MHz processor or higher

z Microsoft® Win™2000/ME/98 Second Edition/XP

2. Driver/Utility Installation / Uninstallation

2.1 Installation

Note! The Installation Section in this User Manual describes the first-time installation

for Windows. To re-install the driver, please first uninstall the previously installed driver. See Chapter 2.3 “Uninstallation” in this User Manual.

Follow the steps below to complete the driver/utility installation:

1. Insert the Installation Software CD into the CD-Rom Drive.

2. Click “Next”.

3. Read the License Agreement and click “Yes”.

4. Click “Next” to continue or click “Browse” to choose a destination folder.

5. Click “Next”.

6. Click “Yes” to create a shortcut icon on your desktop.

7. Click “Finish”.

8. You should now see a shortcut icon on your desktop.

2.2 Additional Setup Processes

During software installation procedure, each operating system may prompt different specific options:

1. Windows 98SE: The system will request the original Windows CD during the

installation process. When the installation is finished, you’ll have to restart your computer.

2. Windows Me: Please restart your computer when the installation is finished.

3. Windows 2000/XP: Select “Install the software automatically” when the window

with this option appears, and then click “Next” to continue installation.

2.3 Uninstallation

Note! Before uninstallation, please close all running programs.

1. Click Start>Programs>WLAN a+b+g mini-PCI Module >UnInstall WLAN a+b+g

mini-PCI Module.

2. Choose “Remove”. Click “Next”.

3. Click “OK” to start Uninstall.

4. Click “Finish”. Uninstall is now completed.

3. Connecting to an Existing Network

1. Double click the shortcut icon of WLAN a+b+g mini-PCI Module on the desktop,

and the Configuration window appears.

2. Click on the Refresh button to list all available networks.

+ 27 hidden pages

Wistron NeWeb DNMA-92 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual