Wistron NeWeb A18QA User Manual

UMC-A18QA Product

Specification

Version

Change history

Date

0.1

Preliminary release

2018/06/01

UMC-A18QA LGA-type LTE Module

User Manual

Wistron NeWeb Corp.

啟碁科技股份有限公司

Revision History

CONFIDENTIAL

THIS DOCUMENT CONTAINS PROPRIETARY TECHNICAL INFORMATION, WHICH IS THE

PROPERTY OF THE WISTRON NEWEB CORPORATION AND SHALL NOT BE DISCLOSED TO OTHERS IN

WHOLE OR IN PART, REPRODUCED, COPIED, OR USED AS THE BASIS FOR DESIGN, MANUFACTURING,

OR SALE OF APPARATUS WITHOUT WRITTEN PERMISSION OF WISTRON NEWEB CORPORATION.

Page 1

UMC-A18QA Product

Specification

C O NTENTS

A. Product Description ......................................................................................... 3

B. Main Features ................................................................................................. 6

B.1 Application interface features ......................................................................................... 7

B.2 Packet mode features ..................................................................................................... 7

B.3 LTE features ..................................................................................................................... 7

B.4 Short Message Service (SMS) features ............................................................................ 7

B.5 RF Specification ............................................................................................................... 8

E. Mounting considerations ................................................................................. 9

F. Mechanic Specifications ................................................................................. 10

G. Package Specifications ................................................................................... 12

H. Label Form.................................................................................................... 12

I. Electrostatic discharge (ESD) ........................................................................... 13

Page 2

UMC-A18QA Product

Specification

A. PRODUCT DESCRIPTION

THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN IS PROPRIETARY AND

IS THE EXCLUSIVE PROPERTY OF WNC AND SHALL NOT BE DISTRIBUTED,

REPRODUCED, OR DISCLOSED IN WHOLE OR IN PART WITHOUT PRIOR WRITTEN

PERMISSION FROM WNC.

LIMITATION OF LIABILITY

THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN IS PURELY FOR

DESIGN REFERENCE AND SUBJECT TO REVISION BY WNC AT ANY TIME. NOTHING IN

THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY WARRANTY OR RIGHT TO

USE THE MATERIAL CONTAINED HEREIN WITHOUT WNC’S PRIOR EXPRESS WRITTEN

CONSENT. WNC SHALL NOT BE LIABLE FOR ANY USE, APPLICATION OR

DEVELOPMENT DERIVED FROM THE MATERIAL WITHOUT SUCH PRIOR EXPRESS

WRITTEN CONSENT.

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must

accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiated radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

Page 3

UMC-A18QA Product

Specification

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for

compliance could void the user‘s authority to operate the equipment.

End Product Labeling

The final end product must be labeled in a visible area with the following: “Contains FCC ID:

NKRA18QA”. The grantee's FCC ID can be used only when all FCC compliance requirements are

met.

RF Exposure Information

This device is intended only for ODM/OEM integrators under the following conditions:

(1) The antenna must be installed such that 20cm is maintained between the antenna and users,

(2) The transmitter module may not be co-located with any other transmitter or antenna.

(3) To comply with FCC regulations limiting both maximum RF output power and human

exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure

condition must not exceed:

Standalone Condition:

1.0 dBi in 700 MHz Band

1.5 dBi in 850 MHz Band

5.5 dBi in 1700 MHz Band

3.5 dBi in 1900 MHz Band

IMPORTANT NOTE:

This module is intended for ODM/OEM integrator. The integrator is still responsible for the

FCC compliance requirement of the end product, which integrates this module. 20cm

minimum distance has to be able to be maintained between the antenna and the users for

the host this module is integrated into. Under such configuration, the FCC radiation exposure

limits set forth for an population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

Page 4