Wisdom Sage P48, Sage P38m, Sage P38i Owner's Manual

Download

Page 1

Owner’s Manual

Sage P48, P38m, P38i

Biamplied

Planar Magnetic Hybrid

Loudspeakers

Page 2

Table of Contents

Introduction ....................................................................................................4

About this manual ..................................................................................................4

Please register your system ....................................................................................4

Description .....................................................................................................5

Planar magnetic panels ..........................................................................................5

Free from compression....................................................................................5

More reliable ..................................................................................................5

Easy on ampliers ...........................................................................................6

Dynamic woofers...................................................................................................6

Big bass in small boxes? ..................................................................................6

Extraordinary drivers .......................................................................................6

Designed for biamplication ..................................................................................7

SC-1 System Controller ....................................................................................7

Unpacking & Setting Up the P48.....................................................................8

Attaching the bases ................................................................................................8

When to install spikes ............................................................................................8

Remote Setup via Modem ......................................................................................8

Making the P48 Connections ........................................................................10

Unpacking & Installing the P38m ..................................................................11

Mounting the P38m on the wall ..........................................................................11

Unpacking & Installing the P38i ....................................................................13

Installing the P38i in the wall ..............................................................................13

Room Acoustics & Placement ........................................................................15

Start With the Room ............................................................................................15

Rigid Walls ....................................................................................................15

Speaker Placement ...............................................................................................16

Left & Right Speakers ....................................................................................16

Center Channel .............................................................................................16

Surround Speakers ........................................................................................17

Subwoofer Placement ..........................................................................................17

Room Treatment ..................................................................................................18

Professional Acoustic Design ...............................................................................18

References ...........................................................................................................19

Optimizing the System ..................................................................................20

Care & Maintenance .....................................................................................21

North American Warranty ............................................................................22

Twenty Year Warranty ..........................................................................................22

Obtaining Service .........................................................................................23

Specications ................................................................................................24

P48 Dimensions ............................................................................................25

P38m Dimensions .........................................................................................26

P38i Dimensions ...........................................................................................27

Notes .............................................................................................................28

Page 3

Page 4

Introduction

Congratulations on purchasing your Wisdom Audio system. It incorporates many design features designed to give you decades of pleasure and performance. Many of these design choices are uncommon among loudspeaker manufacturers, and bear some explanation. See the following section entitled “Description” for more information.

Our unique driver designs and our emphasis on achieving real-world performance account for the “system” approach taken. These are not speakers that are simply connected to speaker wires and promptly forgotten. We recognize that setting up a Wisdom Audio system is a bit more involved than connecting a common set of loudspeakers, which is why we insist that our dealers perform the installation and calibration of the systems. We know that the extra effort (particularly as regards setting up the SC-1 System Controller) yields vastly improved results.

About this manual This manual focuses on the loudspeakers themselves. In order to fully under-

stand the system, we recommend you also review the manual for the SC-1 System Controller, without which these speakers will not perform correctly.

While we expect your local Wisdom Audio dealer to take care of the setup and

calibration of the system, we still recommend that you at least briey review this and the other manuals (SC-1, SA-series ampliers) to understand the system’s full

capabilities.

Your Sage P48 loudspeakers are specically designed to avoid the compromises

inherent in conventional speaker designs. The active crossover and room cor-

rection circuitry in the SC-1 is essential to the speakers’ proper operation. In addition, the SA-series ampliers are specically designed to meet the needs of the

unique bass system of your Sage speakers. It is truly a “system” design, and not merely a collection of loudspeaker drivers in a box.

Please register your system To register your warranty, please complete the form at the following address on

the internet:

http://www.wisdomaudio.com/registration/

Doing so will ensure that there will be no delays should you ever require warranty service. If accessing the internet is inconvenient, you can send a copy of the sales receipt (showing your name, address and the products purchased) to the address shown in the North American Warranty section of this manual.

Wisdom Audio does not and will not ever share its mailing list with other companies. Nor do we expect to contact you frequently, since you are buying a product that should last a lifetime. However, we would like to be in a position to contact you should a software update become available for the system controller (as an example).

Lastly, please keep your sales receipt in a safe and easily found place. If you do not register your purchase with the company, it is your only proof of warranty.

Page 5

Description

Your Sage loudspeakers take advantage of several critical technologies to deliver a level of performance that has never been available in a loudspeaker that intruded so modestly on your living space. In fact, this level of performance has rarely been attained, regardless

of the space and budget at one’s disposal.

Since most of these technologies cannot readily be found elsewhere, we will take the time to describe them in more detail than would be necessary for more conventional designs.

Planar magnetic panels Our planar magnetic drivers use an advanced, thin lm membrane

to move the air. This lm can respond instantly to the smallest

detail in the signal. It has vastly less inertia than traditional “cone & dome” drivers, so the signal is never blurred in any way.

The motive force is provided by a “voice coil” that is printed on the lm, which is suspended in a strong magnetic eld provided by neodymium magnets behind and in front of the lm. The ratio of available force to the moving mass

is huge, which means that the diaphragm does exactly what it is told; nothing more, nothing less.

Free from compression One of the most remarkable things about

the sound of well-designed planar magnetic speakers is their lack of thermal or dynamic

compression. There are several reasons for this:

• The lightweight diaphragm responds quickly to even the smallest

signals, yet is robust enough to handle enormous ones.

• The fact that heat does not build up in the voice coil (as it does

in conventional dynamic drivers) means that the load seen by the

amplier does not change at high power levels.

• The pleating of the diaphragm allows greater excursions than are

otherwise available to small planar magnetic devices, further enhancing the driver’s ability to respond to dynamic program material.

When you become accustomed to the sound of your new Sage P48 speakers, conventional speakers sound a bit bland and lifeless.

More reliable The “voice coil” in the planar magnetic driver is spread out over a large, at area

that is exposed to the open air. As such, when a huge transient comes along, any heat that is generated is immediately dissipated. This compares quite favorably to other designs in which the voice coil is buried inside a massive piece of metal, where the heat has effectively no place to go.

The excellent heat dissipation of these drivers makes them remarkably reliable. Planar magnetic speakers can handle a great deal of power without undue stress

Page 6

or audible strain. In fact, for a given size, they can handle many times the power of a traditional dynamic driver.

Easy on ampliers Because the conductor is essentially a long, thin wire, it presents a purely resis-

tive load to the amplier. This is comparable to the simple test loads that amplier companies use when measuring their ampliers to show how terric they are. As such, you can be assured that your ampliers will sound and work their

best.

For more detailed information on the loudspeaker drivers in general, and planar magnetic drivers in particular, please refer to the Planar Magnetic Technology white paper that can be found on the Wisdom Audio web site, at www.wisdomaudio.com.

Dynamic woofers Authoritative, deep bass requires that you move a lot of air. We have chosen

to use dynamic woofers for the bass because they still provide the best performance at low frequencies as compared to any alternative technology.

In order to get comparable performance from a planar magnetic design, you would need to have a huge speaker that would be impractical in most domestic living spaces. It simply makes more sense to use the best transducer technology

in each area of the reproduced spectrum. One of Wisdom Audio’s strengths is

in seamlessly blending these technologies — particularly important given the high standards set by our planar magnetic drivers.

Big bass in small boxes? There is an old truism in loudspeaker design that goes something like this: “deep

bass, small enclosure, or high sensitivity — pick two out of the three.” No one

can cheat the laws of physics. If you want deep bass from a small box, you will need to make up for the small size with equalization and extra power.

Fortunately, our system design comes to the rescue.

The system design includes both the SC-1 System Controller (which serves as an

active crossover, a system-specic equalizer, and a room correction system) and the matching SA-series ampliers. By dedicating high power ampliers we can

give people what they want: great bass without huge, ugly boxes that are dif-

cult to place.

Extraordinary drivers Of course, the woofers themselves must be rather extraordinary in order to both

handle the power we deliver to them, and to “keep up” with the planar magnetic drivers right up to the crossover frequency.

Our woofers are different because they must be in order to do their job. Specically, we need highly dynamic, uncompressed bass (to keep up with the planar

magnetic drivers) from an unusually small enclosure (so it will t in the wall, or

on the wall, or in a tall, slim freestanding speaker). These two design goals require rather extraordinary attention to myriad details.

The magnetic structures employed in the Sage Series woofers are signicantly

stronger than is commonly available — more than twice as powerful as typical woofers, in fact. In addition, our voice coils are larger and capable of handling more power than would be expected for a driver of similar size. Even the sur-

rounds that attach the diaphragm to the woofer’s basket (the metal frame) have

Page 7

to be unusually rugged. Everything about the woofers has been optimized for their intended application, which involves reproducing powerful, dynamic bass from an extremely small enclosure.

Designed for biamplication People who have wanted to extract the highest performance from their systems

have known for a long time that driving each section of the speaker directly and

separately yields the nest results. Of course, this requires having a dedicated,

active crossover to divide the frequency range appropriately before the power

ampliers, so that they can then drive the speakers directly. It also requires two

sets of speaker wires for each loudspeaker.

Biamplication makes use of two channels of amplication to drive different

portions of the audio spectrum. The most common instance of “bi-amping” today is in home theater applications, wherein a dedicated subwoofer handles the deepest bass, while the remaining audible range is handled by the various front and surround speakers. But you can also biamplify a full range loudspeaker, driving the woofer separately from the drivers that handle the midrange and treble frequencies. Your Sage P48 is such a speaker, designed to use separate

ampliers for the woofer and the planar sections of each loudspeaker.

Since each channel of the amplier is delivering current into its load only over

a limited range of frequencies, several forms of distortion are reduced as compared to each channel handling the full range of musical information. Moreover,

since each amplier is “direct-connected” to the driver for which it is responsible, there are no passive component losses and the amplier can control the motion of its assigned transducer with far greater nesse and precision.

But perhaps most importantly, biamplication allows us to dedicate the amount

of high quality power required to deliver outsized bass from small enclosures. It would not be practical or even possible to obtain bass performance on this level

without a dedicated amplier driving the woofers solely and directly.

SC-1 System Controller In order to realize these benets, an active crossover must accurately divide the

signal into the low and high ranges. The Wisdom SC-1 System Controller serves that purpose, while also providing both system-specic equalization (to compensate for the unusually small woofer enclosures) and sophisticated room correction to minimize distortions introduced by the room itself. The goal is simple:

to achieve consistently excellent results in the real world of the owner’s home.

After all, that’s all that really matters.

Page 8

Unpacking & Setting Up the P48

The Wisdom Audio Sage P48 freestanding speaker is a substantial piece of equipment. Please exercise caution when unpacking your P48 to ensure that you do not strain yourself from its (perhaps unexpected) weight.

Caution! Do not attempt to lift your P48 by yourself. Unpacking these

speakers is easy for two people, but it is unwise for a single person to attempt doing so. Do not attempt to lift your P48 while bending or twisting from the waist. Use your legs for lifting, not your back. Always stand as straight as possible and keep the P48 close to your body to reduce strain on your back.

Your P48 is packed for shipping in two distinct boxes.

The speaker itself is in a “telescoping” box (two ve-sided boxes, one of which ts snugly inside the other). Gently roll the box over so that its bottom is facing

up. Then carefully cut the tape along the bottom of the box on all four sides.

Roll the box over again so the bottom is on the oor, and lift off the top. With

one person at each end, carefully lift the speaker out of the box and lay it on a soft surface (carpet or similar).

Attaching the bases The bases for a pair of speakers are packed separately in a at box. Using the

supplied Allen wrench, attach them to the speaker using the four bolts found in the riser at the bottom of the speaker tower. These bolts should be snug — do

not over-tighten. You will feel when rm, metal-to-metal contact is made. Do

not tighten more than 1⁄8 of a turn beyond the point of initial, snug metal-to- metal contact.

We do not recommend removing the grille on your new loudspeakers. The

grille is an integral part of the design; moreover, the planar magnetic lm should

never be touched, as it is tensioned precisely at the factory. The grille plays an important protective role as well as an aesthetic one.

After unpacking your P48, keep all packing materials for future transport. In the event that you need to ship your P48, only the original, purpose-designed shipping carton is acceptable. Any other method of shipping this product runs a

signicant risk of damage to the P48—damage that would not be covered by the

warranty. (If you lose your packaging and need to ship your speakers, replacement packaging can be purchased from Wisdom Audio.)

When to install spikes The oorstanding versions of the Wisdom Audio Sage Series speakers are sup-

plied with adjustable “spikes” for both leveling the speaker and securely cou-

pling it to the oor. The spikes are shipped with the blunt end exposed. We

recommend experimenting with room placement while the spikes are in this po-

sition. The pointed ends are quite sharp and may scratch the oor, or get caught

on the carpet.

Page 9

Wisdom Audio spikes are reversible for use on either hard or carpeted oors.

The sharp end of the spike is designed to penetrate the carpeting and couple

to the oor beneath, for excellent stability and improved sound. When on tile or hardwood oors, however, use the blunt end of the spike instead to avoid oor damage. In either case, you can adjust the height of the individual spikes to compensate for slightly uneven oors. When this ne adjustment has been

made, tighten the large black nut snugly against the bottom of the base to prevent them from further movement.

Note: If you fail to tighten the black nuts that secure the spikes, they may

rattle a bit when playing music or movies. This rattling can sound like speaker distortion. Fortunately, a quick tightening of the lock nuts on the spikes will eliminate the problem.

After you have determined the nal locations of the P48 speakers, enlist the

assistance of a friend to safely tip the speaker to provide better access to the

adjustable spikes to maximize stability (even with uneven oors). Tilting it even

as little as 15°-20° provides access to the threaded holes for the spikes without

straining your helper. Reverse the spikes if you are on a carpeted oor. Once the rst two spikes are securely in place, switch sides and repeat the process on the

other side. Fine-tune things until the speaker is both solidly stable and plumb.

Page 10

Making the P48 Connections

As with any system, you should make changes to the connections only when the power is turned off to avoid any chance of inadvertently causing a problem (such as a short-circuit).

Two sets of speaker wires are required for each Sage P48 loudspeaker: one for the woofer (low pass) section, and a separate one for the planar magnetic (high pass) section that handles the midrange and treble.

We recommend using heavy-gauge speaker wire, particularly when the installation forces you to use longer wires than you might otherwise. A good rule of thumb is to keep the “loop resistance” below 0.07 ohms.

The loop resistance can be easily measured with an inexpensive volt-ohm meter. Simply twist the two conductors at one end of the cable together, and then measure the DC resistance across the two conductors at the other end of the speaker wire. Doing this measures the total resistance going down one side

and back the other, hence the term “loop resistance.” If this gure is at or below

0.07 ohms, you are in good shape.

For the purposes of this manual, we will assume that you have already connected the SC-1 System Controller as per the instructions found in its manual. As such, you should have signal coming from your source component(s) to a preamp/processor, and then on to the SC-1; following the SC-1, the signal is split into low and high sections, with the low section going to one or more Wisdom

Audio SA-series ampliers, and the high section going to another amplier,

which will drive the planar magnetic panels.

Connect the outputs of your Wisdom Audio SA-series amplier to the appropriate woofer sections, taking care to get both the channel assignments and the

polarity correct. Connect the positive (+) terminals on the SA-series amplier to

the positive (+) terminals for the woofer on the loudspeaker; likewise, connect

the negative (–) terminals on the amplier and the speaker, respectively.

Next connect the outputs of your chosen amplier for the midrange/treble to

the Sage P48 planar sections in a similar fashion, taking care with both channel assignments and polarity.

Page 11

Unpacking & Installing the P38m

The Wisdom Audio Sage P38m on-wall speaker is a substantial piece of equipment. Please exercise caution when unpacking your P38m to ensure that you do not strain yourself from its (perhaps unexpected) weight.

Caution! Do not attempt to lift your P38m by yourself. Unpacking these

speakers is easy for two people, but it is unwise for a single person to attempt doing so. Do not attempt to lift your P38m while bending or twisting from the waist. Use your legs for lifting, not your back. Always stand as straight as possible and keep the P38m close to your body to reduce strain on your back.

The loudspeaker is packed in a “telescoping” box (two ve-sided boxes, one of which ts snugly inside the other). Gently roll the box over so that its bottom is

facing up. Then carefully cut the tape along the bottom of the box on all four

sides. Roll the box over again so the bottom is on the oor, and lift off the top.

With one person at each end, carefully lift the speaker out of the box and lay it on a soft surface (carpet or similar).

Mounting the P38m on the wall The mounting bracket that mounts to the wall is shipped attached to the back of

the loudspeaker. It is removed by pulling “down” on it relative to the end of the speaker that will be “up” when installed on the wall. (Note that for horizontal center channel speakers, this means the bracket is pulled across the narrow dimension of the speaker.)

Please note that this guide assumes the wall surface is at. If not, shims must

be applied to the rear of the mounting bracket so that the mounting bracket is

uniformly secured to the wall and at (not distorted). The mounting steps are as

follows:

1. Locate the area with the two sets of high- and low-pass speaker cables coming out of the wall.

2. The inside face of the bracket assembly has arrows stamped into it indicating which direction must be “up” when it is mounted on the wall. Align the center screw hole in the mounting bracket next to the speaker cables and attach somewhat loosely using a drywall screw (or similar), so you can adjust the bracket for plumb.

3. Using a bubble level to ensure that the mounting bracket is plumb, mark screw holes for EZ-Toggle screws in end clips, using the bracket itself as your template. You can use any opposing (diagonal) set of holes for mounting of the two EZ-Toggle screws in each end clip.

4. Rotate the bracket out of the way and install two of the supplied EZ-Toggle screws in each mounting bracket end clip as follows:

a. Using a #2 Phillips bit in your cordless drill, spin the E-Z Toggle

Anchor into the drywall until the head of the anchor is seated

ush and the arrows on the head of the anchor point up and

down. Repeat this process for each anchor location.

Page 12

b. To “set” the clamp behind the drywall, place the mounting

screw into the anchor and push or tap rmly until approximately 1” (2.5 cm) of screw is protruding (do not rotate). Then remove the screw. Repeat for each anchor location.

c. Rotate the mounting bracket back over the E-Z Toggles, insert

the screw and continue to turn until fastened tightly. The screw stops when the toggle bar secures itself against the opposite side of the drywall (inside the wall). Repeat for each anchor location.

5. Install screws suitable for the specic wall material (e.g., sheetrock, brick, concrete, etc.) in all of the remaining holes in the mounting bracket to ensure secure attachment to wall and avoid any resonance from mounting bracket. Snug down the center screw at this time as well.

6. Using assistance, while holding the speaker away from the wall, connect both high- and low-pass speaker cables to the rear mounted connectors. Pay close attention to connect the correct wires (high- and low-pass) to their respective speaker connectors while attending to proper polarity.

7. Fix the speaker into the mounting bracket end clips and press down until you hear the speaker lock into the mounting bracket clips. When properly in place, it will snap into position and

remain held quite rmly.

8. Install the security set screw in the end cap, snugging down to the mounting clip with the supplied Allen driver. This set screw prevents the speaker from coming loose by eliminating the vertical movement required to free the speaker from the bracket.

If you need to remove the speaker from the bracket for any reason, rst remove

the security screw using the supplied Allen wrench. A sharp upward rap with the base of one hand or even a non-marring, dead blow hammer will help jar it loose. (Make sure the speaker itself is being supported by an assistant so it does not come free from the wall unexpectedly.)

(rear of P20m shown at right)

Page 13

Unpacking & Installing the P38i

Your new Wisdom Audio Sage P38i in-wall speaker is a substantial piece of equipment. Please exercise caution when unpacking your P38i to ensure that you do not strain yourself from its (perhaps unexpected) weight.

Caution! Do not attempt to lift your P38i by yourself. Unpacking these

speakers is easy for two people, but it is unwise for a single person to attempt doing so. Do not attempt to lift your P38i while bending or twisting from the waist. Use your legs for lifting, not your back. Always stand as straight as possible and keep the P38i close to your body to reduce strain on your back.

The loudspeaker is in a “telescoping” box (two ve-sided boxes, one of which ts snugly inside the other). Gently roll the box over so that its bottom is facing

up. Then carefully cut the tape along the bottom of the box on all four sides.

Roll the box over again so the bottom is on the oor, and lift off the top. With

one person at each end, carefully lift the speaker components out of the box and lay them on a soft surface (carpet or similar).

There are two major pieces involved in a single P38i loudspeaker:

• the Uni-Grip™ in-wall mounting system

• the speaker module itself

Installing the P38i in the wall 1. Determine the area for the speaker installation and locate the

cutout guide using push pins to secure it in place. Ensure that the template is plumb using a bubble level or similar. Note: Make certain that there are no studs, plumbing or electrical conduit in the intended area behind the wall before you begin marking and cutting!

2. Trace the outer perimeter of the cutout guide with a pencil or a utility knife.

3. Remove the traced section of sheet rock using a keyhole saw, and clear debris from the edge of the hole.

4. Push any insulation to the side.

5. Disassemble bezel/Uni-Grip™ and place the supplied Allen head

screws to the side. Place the bezel in the wall cutout and insert

the Uni-Grip clamping bar through the opening at an angle, working on one side rst. Reinstall the Allen head screws with the

supplied 3/32” drill bit, securing both pieces to each other (sandwiching the wall between them), but do not tighten yet. Repeat on the other side.

6. Using a level, adjust assembly in wall cutout to ensure that the assembly is plumb. Tighten the Allen screws. Do not over torque

or strip these screws. The large clamping area of the Uni-Grip

system does not require unusually high torque on the screws to be secure.

7. Paint the bezel and grill as necessary, being careful not to plug up the holes in the grille. Note that the speaker modules are not

Page 14

mounted in the bezel and grille assembly at this time. They can be mounted later, after all the paint is dry.

8. Using assistance to hold the speaker modules away from the wall, connect both high and low pass speaker cables to the two connectors at the end of the back box, paying attention to assign the correct band-pass and polarity to their respective speaker connectors.

9. Insert the speaker/back box assembly into the Uni-Grip frame and

attach using the supplied Allen head screws and 3/32” drill bit. Do not over torque or strip these screws.

Page 15

Room Acoustics & Placement

Wisdom Audio believes in equalization. Assume for a moment that you had a “perfect” loudspeaker: as soon as you place it in your room, its perfection is gone. In fact, even good rooms often introduce deviations of 20 dB to the response of the system.

It seems strange to us to worry about tenths-of-a-decibel differences between one component and another when there are 10-20 dB problems right there in the room with you.

At the same time, room equalization is not a panacea. It does not solve all problems. In fact, and somewhat paradoxically, EQ works best when it has the least to do. It is best used as the “nishing touch” on an otherwise good system. Unfortunately, most people do not understand that the most important component in their system is their listening room.

This manual does not have the space for a full description of everything that goes into creating excellent room acoustics; doing so would require a textbook of several hundred pages. Instead, we will give you some ideas, and some references to pursue should you want to learn more.

Start With the Room There are many myths oating around pertaining to what a “good room” should

be like. One of the most common is that it should have non-parallel walls. Without going into the details, we recommend staying with rectangular rooms whose dimensions do not share common divisors.

Thus a room with dimensions of 8’ by 16’ by 20’ would be quite poor (since the dimensions are all divisible by a length of 4’, and 16 is also multiple of 8). By contrast, a room whose dimensions are 9’ by 16’ by 29’ would be much better,

since none of the dimensions are mathematically related to one another.

There are innite variations on this idea. If you have the exibility to choose (or

modify) your room dimensions to avoid such problems, do so. Either way, our room correction will be a big help.

Rigid Walls Another myth that should be dispelled is the notion that the walls (and ceiling

and oor) of the room should be extremely rigid in order to reproduce good bass. Rigid, inexible walls reect energy extremely well; thus you will keep

more of the bass energy in the room. This much is true. However, those rigid walls will only increase the amplitude of the standing waves that your room naturally supports. In simple terms, you will have more bass, but it will also be more irregular, with larger peaks and valleys in the response.

Walls that ex a bit (but do not rattle) are much better. Coincidentally, traditional American residential construction standards (sheet rock on wooden studs) are not a bad place to start. You can do better still with professional help, but studs and sheet rock are better than poured concrete. (If your listening room is in the basement, a false wall can easily be built in front of the concrete. You probably need something like this for insulation and aesthetics anyway.)

The ultimate in dedicated listening room construction involves the design and

construction of oating walls, ceiling and oor. This approach yields the added

Page 16

benet (when done properly) of providing outstanding acoustic isolation from

adjacent spaces as well as superb bass reproduction. This approach goes well beyond the scope of an owner’s manual; if you are interested, you should contact a professional acoustician who has specialized in this sort of domestic room design.

Speaker Placement Within the room itself, placement of the speakers and the listener will have a

profound effect on the performance of the system, particularly below 300 Hz

or so. There is no “perfect” position that will solve all problems, but nding the

best compromise will make it easier to solve the remaining problems with the SC-1.

Your Wisdom Audio dealer can help you with optimizing your speaker placement, which is never quite as simple as it seems it should be. The characteristics you should listen for are several:

Left & Right Speakers Goal #1: Stable, 3-dimensional stereo imaging

This usually requires reasonable symmetry within the room, and a bit of space between the speakers and adjacent side walls (to minimize the adverse effects

of early rst reections). Mono (correlated) pink noise can help here, though it

does not replace listening to music. With pink noise playing in both speakers, you should hear a tightly-dened little “ball” of pink noise oating in space exactly halfway between the speakers.

Goal #2: Smooth, consistent bass

Oft-cited rules of thumb for smoother bass reproduction include both “placing the speakers at different distances from the side walls vs. the wall behind them,”

and “placing them at ‘odd fractions’ of the room’s dimensions” (e.g., fractions

in which the denominator is an odd number, like 1⁄3, 2⁄5, 2⁄7, etc.). But nothing replaces your experience in your room, combined with your dealer’s experience in a variety of rooms. Playing pink noise through the woofer sections of your Wisdom Audio speakers (with the microphone at the listening position, and prior to doing any equalization) and watching the results on a Real Time Analyzer (RTA) will let you see the results of your labors.

Center Channel Center channel height

Once you have a solid stereo image up front (when listening only to the Left and the Right speakers), you need a center channel speaker for multichannel reproduction. It should be centered between the Left and Right, and centered on the

screen’s location, preferably at the same height as the Left and Right speakers.

This presents an obvious problem: you cannot place a speaker in front of your television screen.

Ideally, a center channel speaker would be behind an acoustically transparent front projection screen and would match the Left and Right speakers. Doing so would ensure the best possible consistency of tonal balance, image height, and dynamic capabilities for the critical center channel.

Another way to achieve similar results without relying on an acoustically transparent front projection screen is to use a total of four front speakers:

• two widely-spaced P48 speakers handle the Left and Right channels;

• two P48 speakers closely anking the screen both play the (mono)

center channel signal.

Page 17

This approach creates a stunningly convincing “phantom” center image that ap-

Sub 1

Sub 2

22°

30°

90°

110°

135°

150°

0°

pears to emerge directly from the center of the picture, while allowing you to use any display device you choose.

Failing an acoustically transparent screen or a phantom center channel approach, the important thing is to match the tonal and dynamic capabilities of the Left and Right speakers while minimizing the change in image height as a sound is panned across the front stage. Wisdom Audio has designed horizontallyoriented planar magnetic hybrid speakers that will match your P48 loudspeaker superbly; place them as close to the edge of the screen as is practical.

Surround Speakers Surround channel geometry

In a 5.x channel system, the surround should be placed either directly to the sides of or slightly behind the listening area (90°–110° from the center channel, as seen from above). In a 7.x system, the surround speakers should be closer to 90° from the center speaker, and the surround back speakers should be at approximately 135°–150° from the center speaker. This conforms to industry standards, and ensures that you hear what was intended from a spatial placement point of view. (Too often, the surround speakers are all behind the listeners, cre-

ating a big “hole” in the soundeld between the front and the back.)

One possible exception to these guidelines: if you have a THX®-certied pro-

cessor and are using the THX Advanced Speaker Array™ circuitry, you should follow the guidelines in your owner’s manual for the processor. Using this

technology, it can actually be more effective to have the rear speakers in a 7.x system directly behind you and immediately adjacent to each other.

Subwoofer Placement Subwoofers offer somewhat greater exibility in placement, since the frequen-

cies they reproduce are not readily localizable by the human ear. This is due to the fact that the wavelengths they reproduce are more than ten feet (3 meters) long, but our ears are located only about 6-7 inches (17 cm) apart. Thus these extremely long waves do not contribute meaningfully to the imaging that the main speakers create.

However, this fact does not mean that the placement of the subwoofers has no effect on the sound quality in the room. Far from it. The subwoofers are the

a 7.2 channel system layout

Page 18

most likely to suffer from the response irregularities introduced by the room itself, operating as they do below approximately 80 Hz in most systems.

Recent research into the behavior of rooms as a function of speaker placement

has concluded that — if you have the freedom to do so — there are signicant

advantages to placing several smaller subwoofers around the room, rather than relying on a single large woofer. Moreover, the optimum placement is usually centered on each of the four walls. If you have the luxury of doing so, this simple placement strategy can reduce the size of the room’s response irregularities from 20 decibels down to perhaps as little as 6-8 decibels—a tremendous improvement.

Reducing the room’s inherent problems to this degree provides a huge advantage. It allows the SC-1 System Controller to put its considerable abilities to work on perfecting your system’s response, rather than on trying to perform major corrective surgery.

Room Treatment Rectangular rooms have six reecting surfaces (four walls, ceiling and oor)

that reect sound to the listener, after various delays introduced by the indirect routes the sound take on their way to the listener. These rst reections are par-

ticularly damaging to sound quality. Looking at the simplest case of stereo reproduction, you have a minimum of twelve rst reection points in your room that deserve some attention.

Unfortunately, it is often difcult to do much about the ceiling and oor reections, even though they are arguably the most destructive. (The minimization of

these reections is one of the strongest arguments for the tall, line source loudspeakers that Wisdom Audio builds.) This leaves you with eight “rst reections”

that you should consider minimizing somehow. These points are easily found by having an assistant slide a small mirror along the four walls of the room, while you sit at the listening position. Any place on the wall where you can see a re-

ection of any speaker is a rst reection point. Concentrate on the rst reections for the Left and Right speakers rst.

If you can, arrange to apply either absorption or diffusion at these eight points (don’t forget the wall behind you). Absorption can be as simple as heavy, insulated drapes; diffusion can be provided by a well-stocked bookcase with books of varied sizes. Alternatively, you can buy purpose-designed room treatments (some sources listed under References, below).

The important things to remember are these: a good room should have a balance of absorption and diffusion; and if you are going to treat only a few areas

of the room, the rst reection points are the most important ones to treat.

Professional Acoustic Design Does this all sound too complicated? For good reason. It is complicated.

The difference between the average listening room and one that is professionally designed and implemented is huge. A great listening room will disappear to an astonishing degree, letting the experiences captured in your recordings speak to you directly. A well-designed room is also quieter and more comfortable. It can easily become a favorite retreat for peace and rejuvenation.

If you decide to investigate the possibility of improving your room with the help

of a professional, it is important to nd someone who focuses on residential

spaces. Most acousticians are trained to deal with large spaces — airports, au-

Page 19

ditoriums, lobbies in commercial buildings, etc. The problems seen in “small” rooms (residential spaces) are quite different, and outside the experience of most acousticians. Find someone who specializes in and has a great deal of experience designing home studios, home theaters, and the like. Your Wisdom Audio dealer may be such a person; failing that, he/she can help you nd such a professional.

References Books on Acoustics:

The Master Handbook of Acoustics, F. Alton Everest, TAB Books Sound Reproduction: The Acoustics and Psychoacoustics of Loudspeakers and Rooms by Dr. Floyd Toole, Focal Press

Suppliers of Acoustic Treatments:

Acoustic Innovations, http://www.acousticinnovations.com/ Acoustic Sciences Corporation, http://www.acousticsciences.com/ Echo Busters, http://www.echobusters.com MSR Acoustics, http://www.msr-inc.com/home_theater/hometheater.html

RPG Diffusor Systems, http://www.rpginc.com/

Page 20

Optimizing the System

A Wisdom Audio loudspeaker system is just that: a system, designed to provide the highest calibre of performance, in the widest variety of possible settings. As such, simply connecting all the wires does not mean the system is optimized.

The SC-1 System Controller manual has the pertinent details on precisely how to use it to optimize the performance of the system. For the purposes of this

manual, a quick overview of the process is sufcient.

1. Tell the SC-1 which speakers are in the system

The software application that congures the SC-1 for your specic system

has a series of menus that allow your installer to designate which model of Sage loudspeaker is used in each channel of the system. This allows you to mix and match freely, based on the best speaker for a given location.

2. Measure the room

Your installer will use a calibrated reference microphone to accurately measure the performance of each speaker at multiple locations in the listening area. This process ensures that the entire listening area is optimized, rather than optimizing only one location at the expense of others.

3. Select an appropriate target

Large and small rooms have intrinsically different traits. The room correction software allows for these characteristics to be taken into account for superior results.

4. Calculate the necessary room correction

The software then uses the power of the PC to calculate the correction

lters your room requires, and downloads them into the SC-1 for you to

audition.

5. Listen and save the result

You can listen to each set of correction lters prior to deciding whether it meets your expectations. Once you are satised, you can permanently

save the results to the SC-1 (eliminating the need for the PC).

This process can be repeated if necessary, and a total of up to three independent setup memories can be saved for different needs. For example, you might want different setup memories for different conditions such as drapes open vs. closed, or perhaps different target curves for different content (music, movies, gaming). Each of these setup memories can be saved to the SC-1 and then se-

lected as needed, with from the SC-1’s front panel, or via RS-232 and a control

system your installer would create for you.

Page 21

Care & Maintenance

To remove dust from the cabinet of your P48, use a feather duster or a lint-free

soft cloth. To remove stubborn dirt and ngerprints, we recommend isopropyl alcohol and a soft cloth. Lightly dampen the cloth with alcohol rst and then

clean the surface of the P48 with the cloth. Do not use excessive amounts of alcohol—there is no need for the cloth to be wet; merely damp is better.

In the case of stubborn or grimy substances that do not come off the textured surfaces easily, use a clean, plain, pink eraser (such as you might give your child for school work) to remove the dirt. Then nish with a soft cloth lightly dampened with alcohol as outlined above.

Never attempt to clean the drivers themselves.

Caution! Do not touch the surface of the planar magnetic drivers, under any

circumstances. The thin lm has been carefully pre-tensioned at the

factory; any subsequent contact can only damage it.

Page 22

North American Warranty

Twenty Year Warranty When purchased from and installed by an authorized Wisdom Audio dealer,

Wisdom Audio® loudspeakers are warranted to be free from defects in material and workmanship under normal use for a period of twenty years from the original date of purchase.

During the warranty period, any Wisdom Audio loudspeaker exhibiting defects in materials and/or workmanship will be repaired or replaced, at our option, without charge for either parts or labor, at our factory. The warranty will not apply to any Wisdom Audio loudspeaker that has been misused, abused, altered, or installed and calibrated by anyone other than an authorized Wisdom Audio dealer.

Any Wisdom Audio loudspeaker not performing satisfactorily may be returned

to the factory for evaluation. Return authorization must rst be obtained by

either calling or writing the factory prior to shipping the component. The factory will pay for return shipping charges only in the event that the loudspeaker is found to be defective as mentioned above. There are other stipulations that may apply to shipping charges.

There is no other express warranty on this loudspeaker. Neither this warranty nor any other warranty, express or implied, including any implied warranties of merchantability or tness, shall extend beyond the warranty period. No responsibility is assumed for any incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and other states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specic legal rights, and you may also have other rights

which vary from state to state. This warranty is applicable in North America only. Outside of North America, please contact your local, authorized Wisdom Audio distributor for warranty and service information.

To register your warranty, please complete the form at the following address on the internet:

http://www.wisdomaudio.com/registration/

Doing so will ensure that there will be no delays should you ever require warranty service.

If accessing the internet is inconvenient, you can send a copy of the sales receipt (showing your name, address and the products purchased) to:

Wisdom Audio 1572 College Parkway, Suite 164 Carson City, NV 89706

For more information: www.wisdomaudio.com information@wisdomaudio.com Ph: 775.887.8850 Fax: 775.887.8820

Page 23

Obtaining Service

We take great pride in our dealers. Experience, dedication, and integrity make

these professionals ideally suited to assist with our customers’ service needs.

If your Wisdom Audio loudspeaker must be serviced, please contact your dealer. Your dealer will then decide whether the problem can be remedied locally, or whether to contact Wisdom Audio for further service information or parts, or to obtain a Return Authorization. The Wisdom Audio Service Department works closely with your dealer to solve your service needs expediently.

Important! Return authorization must be obtained from Wisdom Audio’s Service

Department BEFORE a unit is shipped for service.

It is extremely important that information about a problem be explicit and com-

plete. A specic, comprehensive description of the problem helps your dealer and the Wisdom Audio Service Department locate and repair the difculty as

quickly as possible.

A copy of the original bill of sale will serve to verify warranty status. Please include it with the unit when it is brought in for warranty service.

Warning! All returned units must be packaged in their original packaging,

and the proper return authorization numbers must be marked on

the outer carton for identication. Shipping the unit in improper

packaging may void the warranty, as Wisdom Audio cannot be responsible for the resulting shipping damage.

Your dealer can order a new set of shipping materials for you if you need to ship your loudspeaker and no longer have the original materials. There will be a charge for this service. We strongly recommend saving all packing materials in case you need to ship your unit some day.

If the packaging to protect the unit is, in our opinion or that of our dealer, inadequate to protect the unit, we reserve the right to repackage it for return shipment at the owner’s expense. Neither Wisdom Audio nor your dealer can be responsible for shipping damage due to improper (that is, non-original) packaging.

Page 24