DELIWRAPPER
MODEL 630
FEATURES:
- INCLUDESADAPTER DISC FOR 10”-12” PIZZAS.
- High watt density heating element shrink wraps
pizza in seconds.
-Thermostatically controlled heating element
provides controlled heat for continuous or
intermittent operation.
- (3) thumb screws remove basic protection shroud
for cleaning. Heat shroud and stainless steel
clean-out tray add to ease of maintenance and
cleanability.
- Heat shroud reduces temperature to prevent film
sticking and provides extra measure of safety to
prevent burns.
-Adjustable pedestal accommodates various sizes
of product for shrink wrapping.
AVAILABLE ACCESSORIES:
ELECTRICAL:
- 120 volts,12.5 amps,1150 watts
- Best when operated on an individual branch circuit
- 6’ power cord length
DIMENSIONS: (does not reflect shipping dimensions)
- 7”H x 12”W x 12”D with adjustable supporting surface.
- 14” diameter protective shield
SHIPPING WEIGHT:
Approx.13 lbs.
- MODEL 650:2 tier dispenser (photo shown)
- MODEL 650-1: Single tier dispenser
- 14” - 16” pizza Adapter Disc ( #0016239)
- 6” - 8” pizzaAdapter Disc ( #0016240)
- SHRINK FILM:
P.O.BOX #10
OREGON,WI 53575
PHONE:608-835-3106
FAX:608-835-8273
FP140022-M
07/10
www.thepizzaoven.biz
Part Sheet Recommended # of Sheets
Number Size For: Per Roll
0017011 16 x 16 8” Pizza 1100
0017018 18 x 18 10” Pizza 600
0017008 20 x 20 12” Pizza 500
0017010 22 x 22 14” Pizza 500
0017009 24 x 24 16” Pizza 500
LIMITED WARRANTY:
WiscoIndustries, Inc. expressly warrants the product willbe freefrom defects in workmanship andmaterials for a period of
1 year from the date of shipment. WISCO DISCLAIMSAND EXCLUDES ANYANDALL OTHER EXPRESS OR IMPLIED
WARRANTIES, INCLUDINGWITHOUT LIMITATION, ANY AND ALL WARRANTIES OF MERCHANTABILITY OR FITNESS
FORA PARTICULAR PURPOSE.
Buyer agrees that its SOLE ANDEXCLUSIVE REM EDY against Wisco and Wisco’s SOLEAND EXCLUSIVE LIABILITY arising
out of any defect or nonconformity in the productshall be replacement/exchange of such nonconforming countertopfood service
equipment at Wisco’s expense. Nocountertop f ood service equipmentshall be returned without Wisco’s consent. IT ISAGREED
THATWISCO’S MAXIMUM LIABILITYSHALL NOT INANY CASE EXCEEDTHE SALE PRICE FOR THE COUNTERTOP
EQUIPMENT CLAIMED TO BEDEFECTIVE OR NONCONFORMING.
MODEL 630-1 DELIWRAP INSTRUCTIONS
UNPACKING AND ASSEMBLY:
- Remove Deli-Wrap from carton
- Remove cardboard from bottom of unit and heating element.
(CAUTION: DO NOT PLUG UNIT IN WITH CARDBOARD HEATING ELEMENT SUPPORT IN PLACE).
- Screw threaded rod into disc.
-Thread wing nut on the opposite end of rod so the wings of the nut face jam nut.
-Thread disc and rod assembly into grille assembly until the height is approx.4-1/2” to 5”.
- Lock wing nut against grille assembly. (The 4-1/2” to 5” dimension given is only a starting place. Due
to the differences in wrapping mediums,you may have to adjust your pedestal height to attain
best wrapping results.)
- Place grille with pedestal assembly on the brackets riveted to the inner shroud.
- Clean out tray can then be put in place. Clean out tray should be centered between shroud
support brackets and resting on the base of the unit.
*You are now ready to plug the unit into a 15amp 115 volt outlet.
CAUTION: THE CARDBOARD SUPPORT MUST BE REMOVED FROM THE HEATING ELEMENT
BEFORE ENERGIZING UNIT.
OPERATION:
Additional Operational Instructions found on page 3
Plug unit in and turn the thermostat switch to the Medium to High position. Pre-heat DeliWrap
machine for approximately 3 minutes.
Place the product being wrapped on the center of the pedestal,immediately tear off a sheet of
shrink wrap material from the Deli-Wrap dispenser and place over product paying special
attention to the symmetry. Best results will be achieved if the wrapping material is evenly laid
over the product.
In approximately 10 to 20 seconds your product will be enveloped and sealed. Remove from
pedestal and allow to cool. CAUTION: DO NOT LEAVE PRODUCT UNATTENDED WHEN WRAPPING.
MAINTENANCE:
Unplug unit before any cleaning,servicing or maintenance is performed.
The outer shroud,inner shroud,clean out tray and grille assembly with pedestal can be removed
for daily cleaning.
CAUTION: ALLOW UNIT TO COOL BEFORE REMOVING ANY PARTS. DO NOT
IMMERSE BASE ASSEMBLY OF THE DELI WRAP IN WATER.
Replace all parts after cleaning.
The Deli-Wrap has been tested and approved by Underwriters Laboratories,to be a safe and
durable product when used and maintained in the manner in which it was intended.
Page 2
Pizzawrap
Perforation
and Capper
FAST and EFFICIENT
1
Step 1:
Step 2:
Step 3:
Step 4:
SIMPLE
STEPS
4
2
3
Tear shrinkfilm at the perforation
*Besure to place film on dispenser so itfeeds
from the bottom. If you pull film from “over” the roll
tearing could occur.
Placecardboardroundw/pizzaon heated deli wrapper;
Place shrink film on top of pizza
Allow deli wrapper to shrink film around pizza
Placewrappedpizzain refrigeratorfor storage; this
unit is not intendedtowrap pizzas for freezing
4
Page 3
Page 3
Page 4
Page 5
WISCO INDUSTRIES INC.
REPAIR PARTS FOR MODEL 630
608-835-3106/800-999-4726
FAX: 608-835-8273
www.thepizzaoven.biz
PART NO:
DESCRIPTION:
0016015 THERMOSTAT
(on/off switch-new style-says HI-MED-LOW)
00100 THERMOSTAT KNOB
00161 19 ON/OFF SWITCH (old style unit)
0016030 *WIRE FOR ON/OFF SWITCH
0016031 *WIRE FOR ON/OFF SWITCH
*need 1 of ea. 0016030 & 0016031
009092 PILOT LIGHT
009551 WIRE
00448 CORD SET
00131 STRAIN RELIEF
0016000 HEATING ELEMENT - 1500W
0016009 WING NUT
001601 1 THREADED ROD
0016241 BAG OF PARTS
(incl. threaded rod, wing nut, disc w/nut assy & hex nut)
0016017 SUPPORT BRACKET
0016018 CLEANOUTTRAY
0016220 INNER & OUTER SHROUD ASSY
0016245 GRILL STAND - COMPLETE ASSY (Incl. stand & #0016241)
001 16 THUMB NUT
00129 INTERNAL WIRE - 13-1/2"
00176 INTERNALWIRE
0018032 FEET
00475 RUBBER INSERTS FOR FEET
00140 WIRE NUT
00150 #8 X 3/8" SHEET METALSCREW
00151 #10-24X 1/4" ROUND HD SCREW
009124 # 10 LOCKWASHER
0016002 GRILL ONLY (stand)
0016012 CARTON
0016239 10-1/2" ADAPTER DISC (for 14"-16" pizzas)
0016240 3-1/2" ADAPTER DISC (for 6"-8" pizzas)
0016244 DISC W/ NUT ASSY (for 10" - 12" pizza)
REV: 1-4-08
Page 6
Loading...