Page 1
FLUSHING
2” outlet
Adjustable
overflow
Colour coded float
adjuster (grey)
Branded
top
Removable
top
1.5m air hoses
Adjustable flush
volumes (full &
part flush)
Grey top
Grey seal
KAYLA Flushing Valve
1.5” and 2”
Outlet Valve
Seal
Coupling Nut
2” or 1.5” Outlet
1.5” Flushpipe
Place the coupling nut, followed by
the seal, on the flushpipe, secure
coupling nut hand tight, tighten
further if necessary, fit finned
flushpipe connector on to flushpipe,
insert into W.C. pan.
2”
1.5”
Seal
Step Ring
Coupling Nut
Insert threaded
section of the valve
into cistern, with base
seal on the inside,
secure with back-nut
hand tight, tighten
further 1/2 turn using
a spanner, check for
leaks, tighten further
if necessary.
2” Flushpipe
Place the coupling nut, followed by slip ring,
then the seal on the flushpipe, ensure the seal
has the bevelled edge pointing towards the
end of the flushpipe, insert the flushpipe up
to the stops in the valve base then secure
coupling nut hand tight, tighten further if
necessary, fit finned flushpipe connector onto
1.5” end of flushpipe, insert into W.C. pan.
SLIDE
To adjust the full flush, move the slide down for more and up for
less. Part flush move the float up for less and down for more.
Always keep the part flush float 1 notch above the full flush setting.
DO NOT GO BELOW SETTING 8
Code:
Issue No.
Date:
PM000PPB
03
19/11/15
Finned flushpipe connector
FLOAT
315mm
maximum
240mm
minimum
The overflow is adjustable from 240mm to 315mm in height. Clip
and lock the overflow 20mm above the waterline in the cistern.
Ensure the overflow is capable of discharging the incoming water.
Finned flushpipe connector
HOSE
CONNECTOR
Clear
Connect the hoses to the button, blue hose to the
end of the barrel nozzle, clear to the centre nozzle.
Make sure the hose connection is firmly on the
nozzle and in the correct order or the part flush
will not work.
Blue
Page 2
KARA PUSH BUTTONS and CASPIA Push Plates
KARA 50mm & KARA 72mm DUAL FLUSH BUTTONS
CHROME
PUSH BUTTON
38mm CUT OUT Kara 50
61mm CUT OUT Kara 72
CASPIA DUAL FLUSH PUSHPLATES
AVAILABLE IN CHROME
MATT OR WHITE FINISHES
CUT OUT
DIMENSIONS
HOSE
CONNECTOR
Clear
Clear
UAL FLUSH BUTTON ASSEMBLY
D
KARA 50mm &
KARA 72mm Buttons
. Cut out 38mm hole for Kara 50 and
1
61mm hole for Kara 72.
2. Put the threaded tail of the button
through the hole and hand tighten the
backnut.
3. Connect the hoses to the button, blue
hose to the end of the barrel nozzle,
clear to the centre nozzle.
Blue
Fix using 4 screws
as indicated
Connect the hoses as follows :
Blue to Centre Blue Cap
and Clear to white cap as shown
KARA 50mm & KARA 72mm SINGLE FLUSH BUTTONS
CHROME
PUSH BUTTON
38mm CUT OUT Kara 50
61mm CUT OUT Kara 72
HOSE
CONNECTOR
Clear
SINGLE FLUSH BUTTON ASSEMBLY
KARA 50mm &
KARA 72mm Buttons
1. Cut out 38mm hole for Kara 50 and
61mm hole for Kara 72.
2. Put the threaded tail of the button
through the hole and hand tighten the
backnut.
3. Connect the hoses to the button, clear
to the end of the barrel nozzle.
Clip on the push plate
as above, to remove the
push plate push the
buttons in and pull left
to unclip
WIRQUIN Ltd.
Warmsworth Halt Industrial Estate, Warmsworth, Doncaster DN4 9LS, United Kingdom
Technical and Sales enquiries: 0044 (0) 333 222 4488
Email: sales@wirquin.co.uk www.macdee-wirquin.co.uk
PM00PCII
Loading...